The inspector doing quality checks and readings, checking the humidity to get the " spread", wet mil gauge ( thickness), blast profile, etc.. I was trying to see if their 6-bagger, blast pot, was the old air pressure switch ( where the pot loses pressure everytime you let off the Deadman switch, or if much more efficient electric 12 V Deadman switch). The painter was doing a lot of whipping around, fan seemed wide. All in all it looked like a good set up, just needs some improvements. I would much prefer to be outside in open air, weather permitting, as far as my health anyway, lol. That little bit of dust is a drop in the bucket, look around at smoke stacks, billowing out tons of pollution, such as coal fired power plants, etc.. All in all, good job guy's. Good video.
@furqan It's not ment for safety it is ment for body fluids, acids and fats it will start rusting , So if you put your hands on clean blasted steel you will have there paint failure in future.
beautiful demonstration but your coating technicians are meant to wear hand gloves for the dust test and not contaminate the blasted surface with your bare hands
Excelente, muy buen. Una pregunta amigo disculpe. Las ochenta o noventa libras de presión deben ser constante o mejor que sostenga para que quede bien limpia la piesa?
In simple term: chemical cleaning remove most of surface contamination including grease and oil traces except few tightly adhered scales, but it won't give any anchor profile for adhesion of paints. In case of blasting, Not only contamination are removed but also achieve a good anchor profile for further coating. The grease and oily substances may not be removed by blasting. The detergent/chemical cleaning subsequent with a water wash are normally done in such cases. Trust this clarify your query. 😊
Dudes like, "dey dont tink i can sand blast this shit...." "Why?" "im so dissapointed" "well im gonna sand blast this shit now eh" No one will get this.
SI NOS BASAMOS A LA TECNOLOGÍA, TODOS ESTOS ACCESORIOS TENÍAN QUE SER SAMBLASTIADO Y PINTADOS EN CAMARAS, ESO ES TÉCNICAMENTE, PERO HAY MUCHO DESPERDICIO DE MATERIALES, PORQUE LOS TRABAJOS NO SE REALIZARON TECNICAMENTE EN CAMARAS, ASÍ ES
A lot more good than Bad. Open air , all good . EPA (BAD) Sling ameter with surface temp? (no) Co2 Monitoring? Rock Guard on Pump. Screen on Blast Pot (1) Should use " fresh air pumps" Soluble salt test before blast, botter test (oily air)internal painting with "dust" mask, Over all " A Plus " in the real World !!!
what you saw on the video was painting so you spray it on the object with air to create an nevel to dek it out, and coating is with powder and elektromagnatic static so the powder stays on the object and then gets heated in around 160 to 200 C :) after that it is finished when it get out of the oven
it is embarrassing that you sandblasting and paint outside without any booth. Do you know that there is only one world to protect and to maintain? This video must be removed from youtube. There is nothing interesting to share with the rest of the world.
Such a amazing and clear video for new candidates
I am a coating inspector nace level 2.... Easy to get how to blast.. good video ❤😊
Good video. It's useful for the basic knowledge of our operators.
Good video for level 1 inspector especially, help to clear understand
I love this video
❤️❤️❤️❤️🇸🇱🇸🇱🇸🇱🇸🇱🇸🇱am from Freetown Sierra Leone 🇸🇱 west Africa 👍
I feel like I’m playing pirates of the Caribbean online with this music lol. Miss that game.
Not going to lie, this video would've been SOOOO much better if there was a narrator explaining everything that was going on.. ty
instead of music, explain the connection and process by voice message
Yes that's what I'm saying
Blasline Basting process and demonstration,,, verry good
Good job...Please edit the video with written steps for best understanding
عز يامال العز المنتج سعودي الي بالكيس البني ١٠٠٪١٠٠
The inspector doing quality checks and readings, checking the humidity to get the " spread", wet mil gauge ( thickness), blast profile, etc.. I was trying to see if their 6-bagger, blast pot, was the old air pressure switch ( where the pot loses pressure everytime you let off the Deadman switch, or if much more efficient electric 12 V Deadman switch). The painter was doing a lot of whipping around, fan seemed wide. All in all it looked like a good set up, just needs some improvements. I would much prefer to be outside in open air, weather permitting, as far as my health anyway, lol. That little bit of dust is a drop in the bucket, look around at smoke stacks, billowing out tons of pollution, such as coal fired power plants, etc.. All in all, good job guy's. Good video.
Congratulasion.. from supervisi Blasting painting company PT Bukaka teknik utama. Jakarta Indonesia
Sir I'm pentar m ye job karna chata hu my no 9050057418 sir palse
@@KrishanKumar-of1ki 9776503041
Like how he did the tape test without gloves on... and touched the blasted steel with his bare hands...
Safety guy spotted
@furqan
It's not ment for safety it is ment for body fluids, acids and fats it will start rusting ,
So if you put your hands on clean blasted steel you will have there paint failure in future.
beautiful demonstration but your coating technicians are meant to wear hand gloves for the dust test and not contaminate the blasted surface with your bare hands
Good 👍✨
Excelente, muy buen. Una pregunta amigo disculpe. Las ochenta o noventa libras de presión deben ser constante o mejor que sostenga para que quede bien limpia la piesa?
Excellent travail
The sandblasting effect of brown corundum abrasive will be better👍👍👍👍👍
This is either Clemco blast equipment painted blue w/ Blastline name one it or an exact replica of Clemco..
Super 👍
Un comentario mexicano vale oro porque sera
What is difference between chemical cleaning and blasting??? For surface preparation
In simple term: chemical cleaning remove most of surface contamination including grease and oil traces except few tightly adhered scales, but it won't give any anchor profile for adhesion of paints. In case of blasting, Not only contamination are removed but also achieve a good anchor profile for further coating. The grease and oily substances may not be removed by blasting. The detergent/chemical cleaning subsequent with a water wash are normally done in such cases. Trust this clarify your query. 😊
Super video
Good job
do they use fresh air or supplied air?
There is a supply line on his back going into his helmet, but I can't tell where that air comes from.
@@billkea7224 It came from same compressor used for this blasting work but it is taken separately through air filter.
এটা কোন দেশের কাজ
que función tiene le regleta amarilla, en el minuto 11:04 que es lo que mide ? alquilen que pueda decirme y como se llama.
Dudes like, "dey dont tink i can sand blast this shit...." "Why?" "im so dissapointed" "well im gonna sand blast this shit now eh" No one will get this.
Où est-ce qu’on peut trouver ce machine de sablage métal et combien ça coûte merci
SI NOS BASAMOS A LA TECNOLOGÍA, TODOS ESTOS ACCESORIOS TENÍAN QUE SER SAMBLASTIADO Y PINTADOS EN CAMARAS, ESO ES TÉCNICAMENTE, PERO HAY MUCHO DESPERDICIO DE MATERIALES, PORQUE LOS TRABAJOS NO SE REALIZARON TECNICAMENTE EN CAMARAS, ASÍ ES
Fernando Hernandez N. El clasico politico que quiere hacer ahorrar a la compañia jajaja dejate de mamadas
😊😊
Excellent but the dust not good for ambient quality
Hi sir water blasting Credit.blasting
Spray. Painting &
Cold cutting
Darking I have known all this for seven years, is there any chance at your place?
How much per hour this job..?
Safety wala blasting karta hai kya ??
Absolutely perfect
Ako dati din sand blasting tank coating sa keppel subic kaya maganda para skin ang gnyang trabaho
Excellent
A lot more good than Bad. Open air , all good . EPA (BAD) Sling ameter with surface temp? (no) Co2 Monitoring? Rock Guard on Pump. Screen on Blast Pot (1) Should use " fresh air pumps" Soluble salt test before blast, botter test (oily air)internal painting with "dust" mask, Over all " A Plus " in the real World !!!
Good video for beginners.... Maybe just check your grit consumption though.... Lot of wastage
What is the white product applied as an internal lining?
Washing up powder to clean it more better I think looool
The stuff with all the paper in it ?lol
What is the preparation used here sa ?
Good
What is difrrence between coating and painting?
what you saw on the video was painting so you spray it on the object with air to create an nevel to dek it out, and coating is with powder and elektromagnatic static so the powder stays on the object and then gets heated in around 160 to 200 C :) after that it is finished when it get out of the oven
Would have explained about work and inspection instead of music
fan var musik det fanns i denna video, uruselt!
What did you add to the paint and in what ratio did it mix?
its not paint it is sand that attack to the surface of steel causing shine
Would be some kinda cure. Like base and resin.
Comes in pre measured kits
It's thinner
TAKE OFF THE GLOVES BROTHER! the couplings wont hurt you
!
what model airless sprayer is he using? I need one urgently
graco airless painting machine , made in u.s.a
So perfect!
I can see he's done a Nace course
Applay blasting painting
Why would u poke ure blast line
Blasting in open area is not allowed, there should be a close room with require ID fan
To check pressure in the line and to see if you do get 6 Bar at the nozzle
Nivel de polvo se realiza previa a la aplicacion.
Jubilee clips????how old is this??
THERE IS NO DETAIL REGARDING HOSE CUNNECTION AND PARTS NAME, WHICH IS IMPORTANT FOR BLASTER BEFOR WORK.
you forget the Co2 monitor
Congratulationes
Thanks a lot
explain how to process maintenance tanker oil ship
If he took them gloves of he would of done that a hell of alot quicker.
Yes that was not PROFESIONAL
GATO CON GUANTES 🧤 NUNCA PILLA RATONES.!!! 😅😅
chris techno puiiswwwee Q
Anton Varga shut the fuck up
Ok
What is the name of your company and the contact number please? I need to buy the same one.
I provide garnet sand in cubic meters
very useful
Top
Get on with it
Better watch out how your cutting them bags of grit open! A little piece of paper can clog that pot
💯
I need a job
why does everyone suck at sandblasting? lol
That steal is stronger than your mum and dad's relationship.
L
it is embarrassing that you sandblasting and paint outside without any booth. Do you know that there is only one world to protect and to maintain? This video must be removed from youtube. There is nothing interesting to share with the rest of the world.
Because sand dust is going to destroy the environment.
Have u seen how they take ships apart 😂😂 this is nothing
No sabes ni usar tu equipo amigo