2014 ford escape timing belt replaced

Поделиться
HTML-код
  • Опубликовано: 4 янв 2023

Комментарии • 34

  • @CoryColt
    @CoryColt Год назад

    If you don't remove the crankshaft pulley and only had to do some work on the cams, do you still need to do anything to set the timing on the bottom end besides put in the one tool to hold the crankshaft at TDC? I'm assuming you can just use the tools on the top-end to set the cams and phases and then slip the belt back on?

    • @antonioaguirre6166
      @antonioaguirre6166  Год назад +1

      If you locked the crankshaft and do not remove the pulley it will be ok. The pulley has the engine timing and the ignition timing too.

    • @emilyhofland8219
      @emilyhofland8219 Год назад +1

      Don't listen to him. The bottom crank is not keyed, or marked. You need to treat this engine like you are doing a full timing job. If you don't lock that crank, it will move, a lot.

    • @antonioaguirre6166
      @antonioaguirre6166  Год назад

      @@emilyhofland8219 this might help ruclips.net/user/shortsxCQ6crfTJt8?feature=share

  • @soyinkakorede8679
    @soyinkakorede8679 Год назад +1

    What is the work of that small special bolt

    • @antonioaguirre6166
      @antonioaguirre6166  Год назад

      It holds the crankshaft at TDC
      there’s another tool that goes on the pulley too to set the ignition timing. I will recomen you to get it too. I didn’t used it cuz I had a mark on my harmonic balancer

  • @mohammadridzuanmddaud1814
    @mohammadridzuanmddaud1814 Год назад

    Hi sir, is it neccessary to lock the flywheel when tightening the crank bolt?

  • @em8819
    @em8819 Год назад +1

    What size socket for the crankshaft bolt? Thanks

    • @antonioaguirre6166
      @antonioaguirre6166  Год назад

      I couldn’t get to you sooner. I don’t remember from the top of my head I want to said is a 10 mil or 11 mil. I’ll be at the shop tomorrow and will tell you for sure the exact size

    • @em8819
      @em8819 Год назад

      Ok thanks👍

    • @antonioaguirre6166
      @antonioaguirre6166  Год назад

      It’s 10 mil

    • @antonioaguirre6166
      @antonioaguirre6166  Год назад

      @@em8819 I made a short for you. Maybe this will help you ruclips.net/user/shortsxCQ6crfTJt8?feature=share

    • @antonioaguirre6166
      @antonioaguirre6166  Год назад

      @@em8819 I try to do it under one minute

  • @user-vi4xt9ou6u
    @user-vi4xt9ou6u 4 месяца назад

    How can I set the crankshaft pulley

  • @user-ph4lf4dr6n
    @user-ph4lf4dr6n Год назад

    Tengo uno en tienpo pero no prende pero si si lo adelanto prede

    • @antonioaguirre6166
      @antonioaguirre6166  Год назад

      Usaste la herramienta para ponerlo a tiempo o así al ojo lo pusiste a tiempo en la polea.

    • @antonioaguirre6166
      @antonioaguirre6166  Год назад

      La polea tiene los dos tiempos el timing belt y el ignition timing

    • @antonioaguirre6166
      @antonioaguirre6166  Год назад

      ruclips.net/user/shortsxCQ6crfTJt8?feature=share

    • @antonioaguirre6166
      @antonioaguirre6166  Год назад

      Hice este vídeo para tratar de explicar mejor

    • @user-ph4lf4dr6n
      @user-ph4lf4dr6n Год назад +1

      @@antonioaguirre6166 gracias ya se que es el fayo