Thank you so very much for your video. My i6X came as Mode 2 but I fly Mode 1 so I did the conversion and I noticed that my throttle wasn't right. So thinking I had done something wrong I went over the swapping of the sticks but couldn't see anything wrong that I did. Then I thought perhaps I need to calibrate them? But wasn't to sure how to do this? But your video explained it all perfectly for me now my throttle sits at 100%. Thanks again!
Grazie Mirek mi hai salvato. Non sapevo piu' come fare, ho anche comprato un gimbal nuovo ma il canale 1 , 2 niente .Ma con il tuo video ho risolto il problema Grazie ancora ciao Grande
If the alieron servowas jittering it's a stick problem the spring is too loose but you have to put a Shim under the screw such as a pc of solder Then you have to modify the case and because of screws going to rub on the back of the case..... I hope this helps someone And look closely you'll see the elevator control has much more spring tension from the factory
Despues de pelear durante dos dias con la puñetera radio recién estrenada, acabo de encontrar este video que me ha salvado de tirarla a la basura. Muchas gracias por enseñarlo. Ahora solo me pregunto cómo has podido conseguir adivinar la solución. Me parece increíble.
I need help! I have a Flysky I6X transmitter to control my tracked inspection bot. But when I first switch the transmitter on, it beeps and gives me this message: "!!WARNING!! Place all switches in their up position and lower the throttle" Sometimes I just bump my left toggle switch, channel 3, and it stops the warning and gives me full control. But all too often, it doesn't matter how many switches and toggles I move around, it just keeps beeping and will not give me control. What is it doing and how do I get it to stop? I have a simple tank chassis with a light and camera gimble on it. It's not like I need a safety switch to start with. Can you help me?
So Simple and successfully done with my TX. Thanks. By the way, when I see the "display" menu, the indicator goes very slowly to center. What's wrong with it? Thanks
Thanks, fixed mine roll stick issue. Wonder what causes it to go out of calibration. I also noticed my battery voltage was low and put in fresh batteries.
Interesting set of options. Oddly it didnt help with the mode reassignment. No matter how I try to set it, channels 1&3 will not move over to the right gimbal. It was working just fine yesterday. I have tried all the resets, deleted models etc. Baffled atm.
Thank for the video. But i am facing a different problem with my elevator stick. When i push the elevator stick up for little value like 20 to 25% servo didn't rotate but when i push the stick further more to 100% the servo moves to its end point. And when i push the stick down it works fine. In down position my servo gives me little pitch varience according to my stick. But in upward push i only get full pitch or zero pitch. What can be the issue. Thanks in advance
Hi , I'm newbie in this rc I just instal flysky fs IA6 with esc40a motor A2212/ 13T 1000kw battery 2200mha 35c e everything works fine but i don't have power in throttle ,can you help me thanks
I have a prob with this radio, I can’t enter the menu anymore to calibrate the sticks, even if I put the sticks to the left and turn on the radio, it will stay on the main screen.., Any ideas???
Thanks I’ve been looking for this for a while.Saved me ordering a new gimbal.Works perfect now.
Mine came from the factory with this issue, but your video had me fixed up in 2 minutes. Thanks
Matthew Balconi So did mine. I was about to send it to the landfill before coming across this video!
Thank you so very much for your video. My i6X came as Mode 2 but I fly Mode 1 so I did the conversion and I noticed that my throttle wasn't right. So thinking I had done something wrong I went over the swapping of the sticks but couldn't see anything wrong that I did. Then I thought perhaps I need to calibrate them? But wasn't to sure how to do this? But your video explained it all perfectly for me now my throttle sits at 100%.
Thanks again!
Thank you so much you have saved me. I sent one Tx back as i thought it was faulty
This also works with the flysky i6x which is what I have
Really really really thanks mate! I was freakin out why the roll in one side was 1100 and the other 1999. Cooool
Thank you for saving my transmitter that had this problem. Great video! Thanks, again!
This video solved my problem... Double Mass bro...
Thanks for posting this video! I was literally about to throw my transmitter in the trash due to my warranty having already expired.
Grazie Mirek mi hai salvato. Non sapevo piu' come fare, ho anche comprato un gimbal nuovo ma il canale 1 , 2 niente .Ma con il tuo video ho risolto il problema Grazie ancora ciao Grande
So easy to follow isithout talking great job ill give it ago thanks
God Bless you. You saved my life thank you very much
If the alieron servowas jittering it's a stick problem the spring is too loose but you have to put a Shim under the screw such as a pc of solder Then you have to modify the case and because of screws going to rub on the back of the case..... I hope this helps someone And look closely you'll see the elevator control has much more spring tension from the factory
Even I understood that! Thank you.
You really solved my problem, now it's alive. I don't need to buy a new one.
Despues de pelear durante dos dias con la puñetera radio recién estrenada, acabo de encontrar este video que me ha salvado de tirarla a la basura. Muchas gracias por enseñarlo. Ahora solo me pregunto cómo has podido conseguir adivinar la solución. Me parece increíble.
Thanks bro it save my life 😘😘
Obrigado, ajudou bastante!
you saved me so much money thank you
Thank You So Much for making this video, You really solved my problem
I need help! I have a Flysky I6X transmitter to control my tracked inspection bot. But when I first switch the transmitter on, it beeps and gives me this message: "!!WARNING!! Place all switches in their up position and lower the throttle" Sometimes I just bump my left toggle switch, channel 3, and it stops the warning and gives me full control. But all too often, it doesn't matter how many switches and toggles I move around, it just keeps beeping and will not give me control. What is it doing and how do I get it to stop? I have a simple tank chassis with a light and camera gimble on it. It's not like I need a safety switch to start with. Can you help me?
So Simple and successfully done with my TX. Thanks.
By the way, when I see the "display" menu, the indicator goes very slowly to center. What's wrong with it? Thanks
Thanks for this video very important information
I almost thought that some solder got disconnected and was about to remove the back cover thank you a lot
Thanks brother
Thanks for this video 👍👍👍👍
Thanks man it’s working
in my fsi6 remote control error shown on the disply and it suddely increases with drone distance . what is the solution for this trouble ?
Thanks, fixed mine roll stick issue. Wonder what causes it to go out of calibration. I also noticed my battery voltage was low and put in fresh batteries.
Thanks! Saved. I was very useful. Many thanks!!!!!! :) :) :)
Thanks. Sincro with novice2?
Interesting set of options. Oddly it didnt help with the mode reassignment. No matter how I try to set it, channels 1&3 will not move over to the right gimbal. It was working just fine yesterday. I have tried all the resets, deleted models etc. Baffled atm.
Thank for the video. But i am facing a different problem with my elevator stick. When i push the elevator stick up for little value like 20 to 25% servo didn't rotate but when i push the stick further more to 100% the servo moves to its end point. And when i push the stick down it works fine. In down position my servo gives me little pitch varience according to my stick. But in upward push i only get full pitch or zero pitch. What can be the issue.
Thanks in advance
Hi , I'm newbie in this rc I just instal flysky fs IA6 with esc40a motor A2212/ 13T 1000kw battery 2200mha 35c e everything works fine but i don't have power in throttle ,can you help me thanks
Thank u this helped me fix my transmitter
Спасибо друг
i get a warning to set alle swichted up and low the left stick but i cant skip the warning, there are a solution?
Thank You So Much for making this video
thank you for solution
dziekuje uratowales mi tylek pozdro
😁
hey !! The issue is with my remote controller, on the LCD - backlight would go on nothing appears on the Screen. What should i do?
I have a prob with this radio, I can’t enter the menu anymore to calibrate the sticks, even if I put the sticks to the left and turn on the radio, it will stay on the main screen..,
Any ideas???
Sir even after positioning in middle it's not taking input of OK, what to do?
will this also work on Flysky fs i6x?
My transmitter isn't showing the receiver votage reading on the LCD screen. please help
My PC doesn't recognize the stick movements any help?
Thank you very much!
thank you bro you amazing
I can acess that menu.
Is any other way to calibrate the stick?
Tnks
I do not know about other calibrations.
Terimakaseh
Thank you
Thank you Bro !
Life saver
You are doing it wrong, for calibrate the sticks after the center position you have to move the gimbal to the edges and recenter and press ok
My flysky FS I6 throttle stick start point is middle pls. help
tq bro...
Punya saya ko ga mau konect ya bang kadnag konect 1detik ilang lgi
my transmitter not binding with resiver i buy new transmitter an it working with my old resiver
so what can i do for my old transmitter
I still waiting for someone to reply... Me too same problem.
@@rightistfreedom8691 ur transmitter is fs i6x or fs i6???
Um milhão de joinha, fiz de tudo, eu já ia comprar outra placa mãe.
YOU ARE BAST ONE
After fixing the stick i get to that bind section and after a while i press cancel and now i can't turn my tx on
teo tit get new batteries
Thank you so much
it works thx
omg , thanksssssss
Why wont my throtle stick work
I cant get into the menu for some reason please can you help :)
try to put all the trim in middle position
Thanks tried that but didn't work
It doesn’t work
Thank you