So... If you're not a car dude, don't have the knowledge to take the panel off, and you already know it's the switch and it's 8:00 p.m. and rain is forecast tonight: how do raise the window?
My passenger window wouldn’t roll up on my Lexus 350. I just put the back window, (known working) switch on my passenger window and BOOM! It works. My switch was bad. Saved me money…yay! Thank you for this video.
THANK YOU! I've been looking for this all day. Cut the cord. THANK YOU! Seriously everything else assumes the motor works or the window is already up. THANK YOU!
You dont have to cut cord if motor don't work. Just remove motor from window regulator and manually raise or lower window as needed with a wrench usually 3/8 drive work
Great videos from A1. For this problem, I wish he would've started with how to remove the door panel, I am pretty novice at this. I'll search for a video on how to do that and then proceed to watch and learn from this one. 👌
My 2012 suv passenger window was stuck down. Your video and others helped me remedy it. Mine was detached cable so, I propped it up-pvc and taped. Stop gap, but OK for now. Northeastern winter coming soon...39 degrees now Northeast USA. Thank you.
Thank you! I have the same problem on my Honda Civic Hybrid VIII: the window just goes down and not up! I procured a new window regulator and it had the sam problem. Now I will procure a new window switch. But my problem is: why, also from the driver side, it is not possible to raise the window? Is there some circuit trick inside the righ side switch that doesn't premit the motor to turn in the oposite direction?
I have a 2006 Honda Civic and I tested the switch with the back window switch. It is doing the same thing. I switched the passenger front switch to the rear passenger side door and it worked both up and down. However, when I used the back passenger side door switch on my front passenger door it did not go down. I know it’s not a motor problem because I ordered another motor and window regulator assembly, and the same problem exists.
Great video man. Love all your stuff especially with the Power Probe. I do have a Power Probe question on this one though; you used a ground wire to ground to the car.. could you have used the Power Probe ground wire that comes out of the bottom instead of using a separate wire to ground it?. Was there a specific reason why you chose not to use the built-in ground system? Thx much
Neither front window would go back up, with a storm coming. Door locks inoperable. View the video...why yes, I did jump my 2009 Nissan Maxima just yesterday due to a run down battery. The process shown on the video worked perfectly! Thank you1
3:20 the blue connector. The one that goes to the motor. I have a 2006 Ridgeline I tried to see if it had any power I end ground and it doesn’t have any of that. I checked all the fuses and they’re all good. can you help me out? I’m not sure what it is.
If all of us automotive drivers would send letters to the manufacturers and tell them we want all metal parts in the window regulators and not cheap crappy plastic parts, maybe our constant problems with these crappy designed systems might improve. I've had 3 replacements in the last two years and had to spend quite a lot of money on repairs!
Nice thought but then greedy folks will.just say "that's how we keep the prices affordable" as if they don't charge too much already. Imagine if they did use quality...they'd cost twice as much (although it would be nice for an after market part supplier & manufacturer to make high quality replacements so we can buy 1 replacement part 1 time fix it once then be done for the life of the car) so good theory but fact of the matter, I think, is they just don't even care smh which is why they use special screws, bolts, fittings & other annoying stuff to make us take it to the dealership...or trust a shady mechanic or stress ourselves out in hopes we cause further damage. Good luck
The switches for both the rear window and the passenger window. Both doors do open just the buttons for the boot door and the glass window for the passenger window too
+Jaybird Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c
What if we don’t have a power probe? Is there any other way to check if motor is working? My switch will not move window up or down but I don’t know if it faulty because I don’t know how to check if power is running to the motor
A little late now but I'll post for others. If the middle windows work but the fronts wont move using the drivers side controls, and the power mirrors don't work (if equipped) there is a high probability it is just the 10A M26 fuse. I'd suggest 1st step regardless would be swapping the horn fuse with the M26 and seeing if that works. Don't just go by visual fuse inspection. In terms of the motor, you can apply power directly from the battery to the motor to see if it works.
I have done all that troubleshooting and the window keeps working but intermittently, one moment it does, one moment it does not. I removed the motor, responds fine forward and reverse. I moved the glass up and down without motor, moves smoothly. As soon as I bolt the motor it works a few times and then stops responding. I replaced the switch, same thing. And of course the only thing I have not replaced is the regulator pantograph because nobody has it new.
Rather than cutting the regulator wire cable, I would disconnect the motor from the refulator gear and turn the regulator gear with a pair of needle nose pliers. That way, you would save almost 100 bucks not replacing the window regulator.
Also,tap on the switch that's not working. They wear out,or get dirty and wet. If you tap as you are trying to roll it up,it may ingage. In my case it did. Thanks
What if the driver door master switch AND the rear door switch both lower the window, but neither will raise the window? It's highly unlikely that both switches went bad at the same time.
i tried pulling up my window but it goes down instead when it when down it stopped working up and or down. what could be the problem? would it be my regulator assembly?
If all the wiring and motor is good and still doesn't work, on some cars you have to reprogram pcm or bcm to get it to work again. Some switches aren't connected directly to power but through some module first.
In my Peugeot 207cc 2008 the passenger’s window the cord cutted the mechanism is working can you suggest me something?? There is replacement of cord of I had to buy a new mechanism with cord ?
Hi I am your new subscriber. Good Explanation. The case of my Car is different. My Chevy Cruze Driver Side Power Window goes down at Appoximatwly 10CM and create Strong Noise. And I close it it create strong noise....please advise
+WORLD OF VIDEOS We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
thanks heaps for video, whats the cause mine ford territory driver side door glass working and front passenger side working but if i use passenger side switch to up and down, and rear door stuck, can you help me out please
My front passenger window won’t go up using the passenger AND driver side main switch’s. Would that rule out a switch probability and perhaps be a motor or regulator?
+Mike Chahal Thanks for watching! If it's not responding to either switch then the issue is probably going to be with the motor, regulator or wiring. A popular way to go is to replace the motor and regulator assembly as you cover almost all bases.
@@1AAuto Same problem with mine^ except my motor and and regulator works, I replaced it… is it a wiring deal and if so how do I further troubleshoot this
Ok, I got the door panel off and my 2002 chevy cavalier, 4 door sedan's door is pretty much clodsed in. There are some bolts, but it appears that there are some welded silver studs on it. It is NO where as open as the car you worked on, here. What do I do? Thank you.
This guy is like safety Steve got his knee pads on to tell us about window motors lol I think safety is important but this much safety just screams overkill.
I have the same issue in the passenger window but It does the same thing with both switches (Master & passenger switch) the motor only working in one direction.
My passenger window won’t go up from either the driver or passenger switch… so which switch should I replace first? Or what could this be? P.s the motor works perfectly fine
My drivers window 98 Camry wouldn’t go up. Replace the regulator and tested it to make sure the new one worked. Moved up and down until I put it all the way down. Seems like it got locked in place
Hi! I have a 2000 Ford Contour with all doors are locked. I have the keys but, they will not work even when I got a new battery. Can you help? Thanks. Francis
Is it likely to be the switch or the motor/regulator if my window gets stuck in the down position one day, works fine the next day, stops working AGAIN, and then works normally AGAIN? When it does work normally, it seems to reset after I turn on the ignition. Thanks!
Sometimes it can be the wire loom in the door jam. The wires can get frayed from opening and closing the door for years. Pull back that rubber boot and inspect.
POWER PROB (12v contact ?)- My I ask going into your example between 1-2min mark you added "ground wire" got it....then a power probe. My 1st question ..if you set-up backwards will that damage the motor? 2nd question .. if without a power probe can you run a wire with 12Volts to that post (is it 12volts ?)? That is motor connector is #1-ground and the other post is #2-12volts. In other words that power probe is basically running 12volts to that other connector on the motor. I know my motor works because mechanic added "Cordless Tool Battery Pack" ran wires from the pack to that motor connector and window went up. He didn't know I was watching I looked away, then he said to me he would close the window in up position for $70 because he didn't have parts (switch). I have 1993 Isuzu Rodeo just forced into retirement last year with no income (social security soon). Most Grateful ..
My window will not go down without getting stuck. It will go down an inch but when the window is off the regulator or whatever then the regulatot or the lifter works fine. Any ideas what's wrong with it? It's a Ford f150 2001 XLT. It acts like the window hits something preventing it from going down like it should.
Same symptom , but I tried replacing the switch with rear one which works fine. it didn't work. And I tried the switch which looked not working in rear window but it worked. And I connected those pins with wires jumped and it went up suddenly. So, my problem is not related with motor or switch. Then, what could it be ? If master switch on the driver's side has something wrong, could it be happened too ?
2005 T & C. Window stuck down. Switches indicate power is going to motors on both sides, but window does not raise so I don't think it's the motor or the switch (driver's side). I really don't want to cut the wire... ideas please??
HELP!!!! Your videos are great. I love my 1997 4runner Ltd with 240k. I want keep it runner forever. Can you help me with one issue that I can't solve. My passenger door window only goes down but not up. I have replaced the window motor already but it is still having the same issue. I tried both driver and passenger side buttons, checked the fuse but they both can't bring the window up only down. Can you give me a few pointers in troubleshooting the issue. Thanks.
+Web Cityx Thank you for watching! Have you greased up the sides of the window tracks to make sure it is not just getting stuck? You can also crack open the door panel and observe the regulator in operation. That way you might be able to pick up on the issue. Other than that it could be electrical, but would not have any recommendation on a fix. We hope this helps! 1aauto.com
Web Cityx Did you happen to resolve the issue? I'm having the same issue with my passenger side window. Neither driver or passenger switch buttons work in the up position only in the down position. I know the window motor works because the window will raise up if I jump the motor terminals with power. It's not the window switch either since I tried another switch and it didnt resolve the issue.
Did either of you guys resolve this issue? Having the same issue. Replaced the motor, switch is suppling power but it won’t go up without some starting help, then it goes. I’m assuming the regulator? Since there’s not much else to check or replace
+Paxtrxck 090 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
I have a 96 chevy Silverado.....window getting stuck in down position but wont go up...has new switches but still wont go up unless I jump it ...any suggestions???
If the switch is bad on the passenger side, then would the switch on the driver's side work? My window on the passenger side will go down, but not up and for both switches. Would replacing just the passenger side switch fix both of them if that's the problem?
+Ken At this time we are unable to diagnose the issue you are experiencing and would suggest taking your vehicle to a local mechanic for further assistance.
Ken. Did you find out if it was still the switch I’m having the same issue you’d think if the switch was bad the driver side would work but it doesn’t I just replaced the motor and still doesn’t work 🤦🏻♂️
I have a 2011 hyundai genesis coupe and the driver side window regulator won't go up. How do I get the window up to remove it? I have a new regulator, but I can not get the window out nor the regulator panel out because it's attached to the window.
I have a 2016 dodge grand caravan and the driver side window switch , the lock and unlock isn’t working. It does roll down the passenger side. What could be wrong.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
I just installed the driver window cause it wasn’t working but I fixed it now other windows aren’t going down ,any suggestions?
So... If you're not a car dude, don't have the knowledge to take the panel off, and you already know it's the switch and it's 8:00 p.m. and rain is forecast tonight: how do raise the window?
Thank you for explaining all the possible problems, now I feel ready to try to fix my windows.
My passenger window wouldn’t roll up on my Lexus 350. I just put the back window, (known working) switch on my passenger window and BOOM! It works. My switch was bad. Saved me money…yay! Thank you for this video.
THANK YOU! I've been looking for this all day. Cut the cord. THANK YOU! Seriously everything else assumes the motor works or the window is already up. THANK YOU!
Thanks for watching!
Great job
You dont have to cut cord if motor don't work.
Just remove motor from window regulator and manually raise or lower window as needed with a wrench usually 3/8 drive work
Great videos from A1. For this problem, I wish he would've started with how to remove the door panel, I am pretty novice at this. I'll search for a video on how to do that and then proceed to watch and learn from this one. 👌
Before doing anything, just check the fuse.
My 2012 suv passenger window was stuck down. Your video and others helped me remedy it. Mine was detached cable so, I propped it up-pvc and taped. Stop gap, but OK for now. Northeastern winter coming soon...39 degrees now Northeast USA. Thank you.
Great video!!! Took me and my brother a minute but it worked. My window was off track
Great video. My window goes down but not up. And i will try all youve mentioned. Thanks!
Subscribed!
Thank you! I have the same problem on my Honda Civic Hybrid VIII: the window just goes down and not up! I procured a new window regulator and it had the sam problem. Now I will procure a new window switch. But my problem is: why, also from the driver side, it is not possible to raise the window? Is there some circuit trick inside the righ side switch that doesn't premit the motor to turn in the oposite direction?
I have a 2006 Honda Civic and I tested the switch with the back window switch. It is doing the same thing. I switched the passenger front switch to the rear passenger side door and it worked both up and down. However, when I used the back passenger side door switch on my front passenger door it did not go down. I know it’s not a motor problem because I ordered another motor and window regulator assembly, and the same problem exists.
What tool you used for the red wire
Thanks for the pro tip ... saved me a trip to the shop !
+Troy Yee Thanks for checking us out, glad this helped! 1aau.to/m/Shop-1AAuto-c
Excellent video! Now I know what to try! Appreciate this!
DO NOT cut the cord- only makes for bigger replacement issues
03:23 Nice zoomed in shot right here guys. Good job.
+Jay Cee Max Thanks for the feedback!
Great video man. Love all your stuff especially with the Power Probe. I do have a Power Probe question on this one though; you used a ground wire to ground to the car.. could you have used the Power Probe ground wire that comes out of the bottom instead of using a separate wire to ground it?. Was there a specific reason why you chose not to use the built-in ground system? Thx much
Is there any other way then to cut the cords? Awesome video. I wish I would have found this first.
Neither front window would go back up, with a storm coming. Door locks inoperable. View the video...why yes, I did jump my 2009 Nissan Maxima just yesterday due to a run down battery. The process shown on the video worked perfectly! Thank you1
Simple and to the point!
What power probe are you using
Any answers?
Mine was a 40 amp fuse when it should have been 30..fixed that and voila! Working again.
+DeGuzman Design Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
3:20 the blue connector. The one that goes to the motor. I have a 2006 Ridgeline I tried to see if it had any power I end ground and it doesn’t have any of that. I checked all the fuses and they’re all good. can you help me out? I’m not sure what it is.
If all of us automotive drivers would send letters to the manufacturers and tell them we want all metal parts in the window regulators and not cheap crappy plastic parts, maybe our constant problems with these crappy designed systems might improve. I've had 3 replacements in the last two years and had to spend quite a lot of money on repairs!
Nice thought but then greedy folks will.just say "that's how we keep the prices affordable" as if they don't charge too much already. Imagine if they did use quality...they'd cost twice as much (although it would be nice for an after market part supplier & manufacturer to make high quality replacements so we can buy 1 replacement part 1 time fix it once then be done for the life of the car) so good theory but fact of the matter, I think, is they just don't even care smh which is why they use special screws, bolts, fittings & other annoying stuff to make us take it to the dealership...or trust a shady mechanic or stress ourselves out in hopes we cause further damage. Good luck
Can you possibly do a video for Toyota Corolla big body central lock repair... Thanks 👍
Lovely way of explaining 👍👍👍
1:30 to 1:50 was not clear and have no idea what you did.
Yes! You just solved my problem. Now I need to figure out how to change that
NEW SUBSCRIBER LOVE THE GEMS 💎 U DROP
great video bud helped alot I appreciate it.
Great help
The switches for both the rear window and the passenger window. Both doors do open just the buttons for the boot door and the glass window for the passenger window too
Thank you. This video gives me an idea.
thank you. i learned something
Good information thanks boss
Whats the voltage that you gotta supply it with .. 12 vlt??. Or less??.
Thank you!
Everything explained point to point 🔥🔥🔥
+ck wasiq Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Great video. You guys rock .
+Jaybird Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c
What did you use when you using that grounding wire?
Need answer ASAP
What if we don’t have a power probe? Is there any other way to check if motor is working? My switch will not move window up or down but I don’t know if it faulty because I don’t know how to check if power is running to the motor
Did u find a solution I’m in the same situation can’t get window up n no power probe
A little late now but I'll post for others. If the middle windows work but the fronts wont move using the drivers side controls, and the power mirrors don't work (if equipped) there is a high probability it is just the 10A M26 fuse. I'd suggest 1st step regardless would be swapping the horn fuse with the M26 and seeing if that works. Don't just go by visual fuse inspection. In terms of the motor, you can apply power directly from the battery to the motor to see if it works.
I have done all that troubleshooting and the window keeps working but intermittently, one moment it does, one moment it does not. I removed the motor, responds fine forward and reverse. I moved the glass up and down without motor, moves smoothly. As soon as I bolt the motor it works a few times and then stops responding. I replaced the switch, same thing. And of course the only thing I have not replaced is the regulator pantograph because nobody has it new.
Thank you very helpful
Rather than cutting the regulator wire cable, I would disconnect the motor from the refulator gear and turn the regulator gear with a pair of needle nose pliers. That way, you would save almost 100 bucks not replacing the window regulator.
Another Excellent Video :)
Awesome bro great tutorial
Any suggestions for why a window would roll halfway up then stop?
Thank you.
Great Video. My window doesn’t open and close but problem it only opens 3 centimetres down so barely opens
If the drivers side switch won't work either front window put/swap a 10A fuse in the M26 position in the fuse panel.
Also,tap on the switch that's not working. They wear out,or get dirty and wet. If you tap as you are trying to roll it up,it may ingage. In my case it did. Thanks
What if the driver door master switch AND the rear door switch both lower the window, but neither will raise the window? It's highly unlikely that both switches went bad at the same time.
What would you do if even after replacing the switch or verifying it worked the window still would not go up
Could We Use A Silicone Spray In The Window Tracks Temporary Until We Are Able To Get it Fixed or Replaced?.. is it Safe?..
Where is your tester hooked up to in order for you to get the window to go up ?
+Steven Scogin The power probe would be hooked up to the battery.
1A Auto Parts Thank you for clearing up my question in a very fast reply.
1A Auto: Repair Tips & Secrets Only Mechanics Know so it is 12 volts going to the window motor?
@@1AAuto OK that's the part I was missing. The probe part was not explained well.
i tried pulling up my window but it goes down instead when it when down it stopped working up and or down. what could be the problem? would it be my regulator assembly?
If all the wiring and motor is good and still doesn't work, on some cars you have to reprogram pcm or bcm to get it to work again. Some switches aren't connected directly to power but through some module first.
+Dee Dee Thanks for the feedback!
In my Peugeot 207cc 2008 the passenger’s window the cord cutted the mechanism is working can you suggest me something?? There is replacement of cord of I had to buy a new mechanism with cord ?
Hi I am your new subscriber. Good Explanation. The case of my Car is different. My Chevy Cruze Driver Side Power Window goes down at Appoximatwly 10CM and create Strong Noise. And I close it it create strong noise....please advise
+WORLD OF VIDEOS We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
thanks heaps for video, whats the cause mine ford territory driver side door glass working and front passenger side working but if i use passenger side switch to up and down, and rear door stuck, can you help me out please
Do you have any videos on motor/regulator rear window replacement for a 2010 Nissan Altima 2.5sl
+Jim Vela We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1aau.to/m/Shop-1AAuto-c
My front passenger window won’t go up using the passenger AND driver side main switch’s. Would that rule out a switch probability and perhaps be a motor or regulator?
+Mike Chahal Thanks for watching! If it's not responding to either switch then the issue is probably going to be with the motor, regulator or wiring. A popular way to go is to replace the motor and regulator assembly as you cover almost all bases.
@@1AAuto Same problem with mine^ except my motor and and regulator works, I replaced it… is it a wiring deal and if so how do I further troubleshoot this
same symptoms - did you figure this out?
Ok, I got the door panel off and my 2002 chevy cavalier, 4 door sedan's door is pretty much clodsed in. There are some bolts, but it appears that there are some welded silver studs on it. It is NO where as open as the car you worked on, here. What do I do? Thank you.
If both the driver switch and the passenger switch doesn't that warrant a motor diagnosis?
Wow! Love it!
+Wish i Knew Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
This guy is like safety Steve got his knee pads on to tell us about window motors lol I think safety is important but this much safety just screams overkill.
Some of us oldie foggies need knee pads everytime we use our knees. Comes from all the construction jobs.
How did you put the window up with that power thing in your hand
+George Mort Great question. To answer your question in his left hand he is using the power switch from the door panel to move the window back up.
Yes how did u use pwr probe
That’s the tool I want!! I just couldn’t find the name of it .:.I’m get it thanks !
+Lore 353 Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Did the drivers side control panel switch work but the passenger side switch didn’t? Or both not work?
How do you get the inside door panel off
One screw by door lever, one screw by door handle (remove little cover). Otherwise just held on with plastic clips.
where can I get that power prob
I have the same issue in the passenger window but It does the same thing with both switches (Master & passenger switch) the motor only working in one direction.
same symptoms - did you figure this out?
I have the same issue. Do you figure out the problem?
Not very detailed on what to use to make window go up.
Powerprobe
Thanks
My passenger window won’t go up from either the driver or passenger switch… so which switch should I replace first? Or what could this be? P.s the motor works perfectly fine
I read previously the drivers side switch controls the signal to passenger side, so start there. Did you try changing M26 fuse?
My drivers window 98 Camry wouldn’t go up. Replace the regulator and tested it to make sure the new one worked. Moved up and down until I put it all the way down. Seems like it got locked in place
Hi! I have a 2000 Ford Contour with all doors are locked. I have the keys but, they will not work even when I got a new battery. Can you help? Thanks. Francis
Is it likely to be the switch or the motor/regulator if my window gets stuck in the down position one day, works fine the next day, stops working AGAIN, and then works normally AGAIN? When it does work normally, it seems to reset after I turn on the ignition. Thanks!
Sometimes it can be the wire loom in the door jam. The wires can get frayed from opening and closing the door for years. Pull back that rubber boot and inspect.
Can you lower window using same method?
POWER PROB (12v contact ?)- My I ask going into your example between 1-2min mark you added "ground wire" got it....then a power probe. My 1st question ..if you set-up backwards will that damage the motor? 2nd question .. if without a power probe can you run a wire with 12Volts to that post (is it 12volts ?)? That is motor connector is #1-ground and the other post is #2-12volts. In other words that power probe is basically running 12volts to that other connector on the motor. I know my motor works because mechanic added "Cordless Tool Battery Pack" ran wires from the pack to that motor connector and window went up. He didn't know I was watching I looked away, then he said to me he would close the window in up position for $70 because he didn't have parts (switch). I have 1993 Isuzu Rodeo just forced into retirement last year with no income (social security soon). Most Grateful ..
You've got such a perfect soft voice.... For being a mechanic lmao💀💀💀💀
Its the beard
Thats not something a man wants to be told.
My window will not go down without getting stuck. It will go down an inch but when the window is off the regulator or whatever then the regulatot or the lifter works fine. Any ideas what's wrong with it? It's a Ford f150 2001 XLT. It acts like the window hits something preventing it from going down like it should.
Is there a way just to window up?
Same symptom , but I tried replacing the switch with rear one which works fine. it didn't work.
And I tried the switch which looked not working in rear window but it worked.
And I connected those pins with wires jumped and it went up suddenly.
So, my problem is not related with motor or switch. Then, what could it be ?
If master switch on the driver's side has something wrong, could it be happened too ?
Is there a way to put it up manually?
HE TELLS HOW TO DO IT 4:05
2005 T & C. Window stuck down. Switches indicate power is going to motors on both sides, but window does not raise so I don't think it's the motor or the switch (driver's side). I really don't want to cut the wire... ideas please??
HELP!!!! Your videos are great. I love my 1997 4runner Ltd with 240k. I want keep it runner forever. Can you help me with one issue that I can't solve. My passenger door window only goes down but not up. I have replaced the window motor already but it is still having the same issue. I tried both driver and passenger side buttons, checked the fuse but they both can't bring the window up only down. Can you give me a few pointers in troubleshooting the issue. Thanks.
+Web Cityx Thank you for watching! Have you greased up the sides of the window tracks to make sure it is not just getting stuck? You can also crack open the door panel and observe the regulator in operation. That way you might be able to pick up on the issue. Other than that it could be electrical, but would not have any recommendation on a fix. We hope this helps! 1aauto.com
Web Cityx Did you happen to resolve the issue? I'm having the same issue with my passenger side window. Neither driver or passenger switch buttons work in the up position only in the down position. I know the window motor works because the window will raise up if I jump the motor terminals with power. It's not the window switch either since I tried another switch and it didnt resolve the issue.
Did either of you guys resolve this issue? Having the same issue. Replaced the motor, switch is suppling power but it won’t go up without some starting help, then it goes. I’m assuming the regulator? Since there’s not much else to check or replace
@@tonyd.4430 any word??
@@vanquishstorm any word on a fix? My cavalier does this and the motors been replaced a couple times.
YOU CAN JUST REMOVE THE MOTOR AND THE WINDOW CAN BE PULLED UP FREELY
uh...how do you get the paneling off? that would be a logical start to this video.
+newphx We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1aau.to/m/Shop-1AAuto-c
Hey sir, my motor works and my switch is working and making the motor move but my window doesn’t move.. any idea on what it could be?
I can hear a clicking noise when I press down or up on the window switch but it doesn’t go anywhere. Would that be the motor or the regulator?
Regulator
My passenger window will go down but won’t go up from the door switch or the switches on the driver side, could it still be a switch?
+Paxtrxck 090 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
I have a 96 chevy Silverado.....window getting stuck in down position but wont go up...has new switches but still wont go up unless I jump it ...any suggestions???
Do you think its the window motor and not the switch only the driver window can't go down the other windows is good
If the switch is bad on the passenger side, then would the switch on the driver's side work? My window on the passenger side will go down, but not up and for both switches.
Would replacing just the passenger side switch fix both of them if that's the problem?
+Ken At this time we are unable to diagnose the issue you are experiencing and would suggest taking your vehicle to a local mechanic for further assistance.
Ken. Did you find out if it was still the switch I’m having the same issue you’d think if the switch was bad the driver side would work but it doesn’t I just replaced the motor and still doesn’t work 🤦🏻♂️
same symptoms - did you guys figure this out?
Anyone know where I can get a power probe
I have a 2011 hyundai genesis coupe and the driver side window regulator won't go up. How do I get the window up to remove it? I have a new regulator, but I can not get the window out nor the regulator panel out because it's attached to the window.
I have a 2016 dodge grand caravan and the driver side window switch , the lock and unlock isn’t working. It does roll down the passenger side. What could be wrong.
you diagnosed the passenger door switch as faulty by using another switch but wouldnt trying the control from the drivers door confirm this?