Fahren 9005/9006/HB3/H10/HB4 LED Bulb Installation Guide
HTML-код
- Опубликовано: 6 сен 2024
- Hi, guys, this is a video showing how to install Fahren 9005/9006/HB3/H10/HB4 LED healight bulb. If you just buy Fahren LED bulb at the first time, and don't know how to install. Hope this video can help you!
---------------------------------------------------------------------------------------------------------------------------------------------------------------
For more information, please click:
Facebook Page: / fahren-796051144066561
Fahren Website: www.fahren-veh...
--------------------------------------------------------------------------------------------------------------------------------------------------------------
Here comes more installation guide:
H11/H9/H8: • Fahren H11/H9/H8 LED B...
9008/H13: • Fahren 9008/H13 LED Bu...
9007/HB5: • Fahren 9007/HB5 LED Bu...
9003/H4: • Fahren 9003/H4 LED Bul...
TIP: Since they stopped short of how you might mount the driver. I realize this may or may not work for your car and that's probably why they left that part out of the video?
What I did with mine was adjust the locking collar (that part with the set screw) in a way as to get the lamp wire to end up at the top of the headlight assembly once you have adjusted the lamp for the 3-9 o'clock position. Doing this gave me enough of the lamp wire to allow the driver (with double sided tape) to sit on top of the headlight assembly. Hope that makes sense. This was on a 2004 Toyota Camry so your mileage may vary on your car.
I'm wondering I got sent the wrong size ? The metal part before the clips itself doesn't fit Into my housing and I can't get it to push into the headlight socket
Your left headlight needs adjusting, it’s a bit low, or lower your right headlight adjustment 😁
Plz tell how did u place decoder/ ballast ...did u got ballast or not ??
Did u place ballast inside the headlight casing or did u kept it outside ..of outside how u kept wiring ie how u kept it out of dusting covers
The song is bussin'
I installed this one in a 2020 Santa Fe. After the video, I realize I will have to re-install them as I left them 12-6 instead of 9-3. Funny part is that I did it 9-3 first but then I thought it was not that way 😂😂😂
Does it make a big difference if they are not 9-3 ?
@@ricardopucheta1839 the light projection is better in a 9-3 setup as you are able to see a straight horizontal light line at nights…
Works great but won’t fit back in the led is too long. It sticks out to far and hits the inside wall of the van where the headlight casing goes
Bought these for my 2017 Hyundai sonata. When attempting to install the bulb, I noticed the wire harness on the car side and the CANBUD is preventing me from fully seating it into the headlight. Any advice?
so these 9005 bulbs wont fit my headlights that take 9005
maybe on the auto they're using but on mine a nightmare plus on the low beam you have no way of looking at the direction of the chip to know if you installed it a 9/3. The 9005 never fit and that is what the acura website recomended?
I am attempting to install the bulbs in my 2005 Silverado 3500 dually the set I have ordered are type 21urs1 9005/9006 they fit the headlight cases and do burn but the bulb bases are hitting the seating area for the light cases a Dremel tool would be a fix but that is not my first choice do I have the wrong model for my 2005 Silverado?
my driver side always had issues... it would go off and on.... now it just burned out
You don't show where to put the driver as it comes with 2 sided tape and zip ties
I know, right? They show a pic in the manual (for the Forscher model) and say, "Secure the driver in a cool location with included wire ties and double-sided tape." Like... okay, in the winter it'll be in a cool place but what about in the summer when it's 95 degrees F in the Southeastern U.S. I guess you can just let it dangle from the wire harness as it is???
What I did with mine was adjust the locking collar (that part with the set screw) in a way as to get the lamp wire to end up at the top of the headlight assembly once you have adjusted the lamp for the 3-9 o'clock position. Doing this gave me enough of the lamp wire to allow the driver (with double sided tape) to sit on top of the headlight assembly. Hope that makes sense. This was on a 2004 Toyota Camry so your mileage may vary on your car.
Please answer me
Can I use HB3 insted of H9 - H11 ?
Anyone have radio interference after installation? Do I really need resistors when is supposed to be ready to handle this Per the package? I got the 22,000 lumens 9005 so each has 11,000 lumens…
Which cars do use hb4?
When i put on my hi beams, it shines to the ground. When its low beam, it shines high? Whats the problem?
They must be installed wrong
Never had LED. Do you need a Ballast or anything? Is it just plug and play?
They include the ballast, it's the small box he's holding in the middle of the video.
@alex supremo what do you zip tie/double sided tape that to?
Yep,simple.
Anyone know why my lights are blinking??
They won't fit my car what do I do
Get a new car, to fit the lightbulb
@@honglin6437 💀💀💀
@@honglin6437😂
They told me to tell you that you gotta burn the headlight with a lighter.
I like the song, what is it?
It’s called Endeavors
I bought these 9006 LEDs from Amazon. This video is a promo/ad, not installation instructions. How do you mount the ballast/control box that you're holding in your hand? Do you stick it onto the frame, zip-tie it or what? Please make a real installation video
You stick it or zip tie it to whatever you want, where it fits. It's common sense. Just put it somewhere out of the way.
Defs a boomer