Ok I followed video 1, everything went fine. I forewarn people....if you’re anything like me, hv plenty of paper towel and wet paper towels ready for clean up. Once all was done, no ink printed. I purged, cleaned, screwed everything back in...nothing. Then I went into maintenance and did the nozzle & head cleaning few times and it finally worked. I ran the cleaning 4-5 times. With each cleaning, it got better. Go thru each maintenance feature; cleaning, alignment, etc. That should work. Thank u for the videos! Life saver!
I appreciate this video it saved me $$$. I put the wrong ink in and then I followed this video. I only put wrong ink in the black but like a dummy I took all the ink out except the blue. so after only the blue would print. I kept doing nozzle checks, head cleaning & purges & nothing would print. I watched someone else's video & it suggested it might not be a clogg but air. he said to print with the caps open where you fill the ink. I did it & boom like magic it immediately started printing all colors. I seen a lot of people w/ the issue of not printing so thought I'd share. But thanks again for this awesome video!!!
THANK YOU, THANK YOU!! Nothing is more frustrating then your printer not printing! But because of you and your videos you have turning that around for me!! Much appreciation!
ok, followed you last video on converting ET 2720 to sub. Followed you step by step. Printed out 25 pages to get old ink out. Now no printing at all. Following you on this purge video, and its WORKING...YOURE THE BOMB....
Thank you! No one shows you this when doing the video on the change! You sir need to make from start to finish because NO ONE has that out that I have seen. Thanks again!
Thank you G! There are many videos telling you how to swap the ink, but non of them tell you to do what you just did. People are running head cleaning but the lines are empty, its going to be while until you are able to see some come out. Thanks for the info.
Just wanted to update you 55 sheets of regular copy paper later and 4 sublimation sheets it is printing 95% better the lines barely shows on printed images and are really faint when heat pressed. When I cleaned the nozzle for the 22 time the nozzle check had all the black lines complete!! Thank god!!!!
This video is extremely helpful! I found no other video showing this step! I was about to throw the damn printer out the window!! 🤣 You saved the printer and me 🤣🤣🤣
Thanks, this is a lot better than the other guy's video using a cleaning liquid inserted on the damper. Saving a lot of ink too. I wonder what the cause of it. It looks like air was trapped in there. I think this issue will not happen anymore after your fix and if ever it does not print in the future, it will be the printhead clogging.
Well... this happen'd to mine because i used the clean'N solution on another video 1st! It went great, i jus forgot to pull ink thru the dampers so it wuld print back normal like it never happen'd, so I jus shot this video kindof lika part 2
Thank you for the video, my printer works so much better, but I'm still having issues. I am still getting like dotted lines in my black and white images. I saw they are coming from the front rolls any way to prevent that. Any info is really appreciated thank you.
Help! I changed the ink in my 2750 and noticed the cartridges were empty as no ink from the lines were going into the cartridges. I followed your instructions and moved ink into the cartridges unfortunately, it’s still printing blank pages. What am I doing wrong?
What would be the reason when I am trying to add the ink back to the cartridges it’s doesn’t come out like yours I was able to follow everything but know trying to add ink to cartridges and not able too help please
Hi ..I watched your videos and switched out my epson ET2800 to sublimation ink I didn’t flush it with the cleaner. When I did my first print it only printed half the page so I did a couple nozzle checks and print cleaning and now I can’t get it to print nothing at all please help with any recommendations. Thanks
I have an Epson ET-2720 - The ink was low so I added new ink. After that I did a reset ink levels. Now the printer is not printing colors, what I mean is, it acts as though it is printing, runs through the cycle but the pages come out blank. This is what I have done... several nozzle checks, 3 head checks, I pulled the little plastic ink heads (not sure what they are called), I ran solution through them, I have re-primed the ink heads(dampers), I even sucked some of the ink out of the ink tanks to confirm they are not clogged. The printer is running right, no issues, it just won't print any of the colors. The nozzle checks are all blank, no ink on the page. Do you have any suggestions?
Would you happen to know, how I can safely/properly discard any ink I need to take out? I appreciate you and your knowledge so much!!! Your saved my butt alot of money!
i have a et2720 and found your videos so helpful! I was getting no cyan printing, i found this tutorial and found a leak in the damper (the plastic was coming unsealed). I tried to repair it but i was wondering if there is anywhere to buy a replacement if i can't get it to seal?
@@nobodEbiz I found the listing and just ordered 2.... can’t wait for them to arrive! I hole this fixes my issue because this printer has only been used once before this issue started.
If it's still not print'N, U may of had some drawback in the lines, anE air or "clear spots" in the lines can cause this! If not, U can always try our purge method
thank you, I did exactly that and it’s up and working perfectly!! Thank you soooo much for your guidance, I have recommended your videos to several people 🙂
So I want to know how do I make sure that there's no more printer ink inside the Carter Ridge. And wat do I need to clean out the regular ink and put in the sublimation ink
U can always pull from the bottom of the cartridge, i figure'd this out after the video... it's easier. I also use our print head cleaner to be Xtra safe. nobodebiz.com/products/print-head-cleaner-kit-100ml-bottle-10ml-syringe-and-tube-cleaner-cartridges-also-available
I purchased the Epson 2760 everything went smoothly until I did the test print, 2 spaces on black lines, did nozzle clean then horizontal alignment top rectangle on all 7 have a line going through them bottom rectangle not overlapping and is blk with no lines, perfect, vertical check line #1 is not there the boxes below with #'s 1-5 each has 2 lines going through the rest of the rows 2-7 some boxes have lines some do not no matter what I do ..and 40 pages later, cleaned print head and nozzle numerous times please tell me I didn't get a lemon, I've been crying all night over this.
Do you need to wait at all after your purge all the epson ink out? Before you put the sub ink in? I just got rid of all the epson ink but wasn’t sure if I should wait?
Thank you for doing this video, many times was hard to hear what you were saying but think I was able to muddle through, how-ever, when it came to the sublimation ink bottles, I couldn't see anything you were doing and this is the part I need the most. I was a dummy also and filled the ink that came with it!!! did you take plastic off the bottles that came with the printer and refill with sublim? I don't get how you were able to fill the original ink holders, did the sublin ink come with the same tops as the original bottles and fit over the cartridges to fill. I have tried syringes but does not work!!! BTW, cotton swabs would help you clean up some of the drips also and get to where paper towels does not!
I've actuallE done both methods, we sell sublimation ink & at 1st did not have the necessarE bottles with the compatible lids! So... during that time I rinse'd the originals out and jus fill'd with our color POP sublimation ink. We now have our ink bottle'd up specificallE for ecotank printers, so all U have to do is remove the seal under the cap & jus turn the bottle 180° & pour in, NO MESS! Check it out: www.etsy.com/listing/802367896/epson-sublimationeco-tank-ready-color
You are a life saver. I had to do several print head cleanings but it worked in the end. The ink is coming somewhat light though , do you think it will get darker with each printing job?
I followed all your steps and I had to draw ink into the Cartlidge but now my blue is not printing can you suggest anything ?? Thank you for the help!!
hello! This is a weird question but I am trying to convert my already converted epson et2720 into a regular printer. Will this method work to take the sublimation ink out so I can put regular ink in?
Yes... doin it that way wuld be less stressful reallE! Even if a lil sub ink is left behind, it won't matter as much! This video is like part 1 & will help more: ruclips.net/video/Lp6-r7qnVT8/видео.html
It looks like I have a little bit of epson ink still in my printer. How can I remove it or can I add sublimation ink and it will be ok? I also put the printer cleaner through.
Hey do u think u can help me? My printer stopped picking up paper randomly! ET 4700. I had the scanner code thing and I fixed that but now my printer wont pick up paper. All from a damn paper jam! This is a design flaw for sure... but anyway lmk if u can help possibly plzzz!
After i removed the epson ink, what do i do next? I followed the syringe video and extracted the epson ink. How do i start with the sublimation ink? Whats the next step?
I converted my printer into sublimation. Unfortunately it just prints blank pages. My printer sounds like its printing but nothing. Can you please help me.
My niece put a little of yellow sublimation ink on the black side and now after I put the black sublimation ink with the yellow , the printer won’t print black. What should I do? Thanks
U can always re-pull ink thru the dampers, U may have had some drawback! Also... the print purge file method is a process, i do 25 prints, then a print head clean, if it still needs work... i repeat
Happened to me you unplugged something! I followed a video about scannner er2 and was able to get it fixed however now have another issue... this is a real design flaw in the ET series!!
@@nobodEbiz thank you for responding. I’ve been print purging since last night and still nothing. I even pulled some ink through the tubes and still nothing.
Did everEone print the purge files like i did? U gotta remember that this is process, not a step by step solution, the time'N on all of ur results will differ... also, the other ink is still run'N thru the print head... these videos onlE clear'd up the dampers & tanks! I do about 25 sheets of the purge file on premium presentation matte or glossE settings, jus to lay down more ink! Then I run a print head clean. Repeat until I'm back on track with either the file or my nozzle check.
Did everEone print the purge files like i did? U gotta remember that this is process, not a step by step solution, the time'N on all of ur results will differ... also, the other ink is still run'N thru the print head... these videos onlE clear'd up the dampers & tanks! I do about 25 sheets of the purge file on premium presentation matte or glossE settings, jus to lay down more ink! Then I run a print head clean. Repeat until I'm back on track with either the file or my nozzle check.
Can't see what you're doing when your back is in the way, Just saying, I've never cleaned an epson before so I need to see what you're doing. I have no idea if you removed anything or added somethings??????
Also my printer was printing perfectly fine until this paper jam. this is a bad time for this cuz i already refunded nearly 1k in these coupleday :( fml
Ok I followed video 1, everything went fine. I forewarn people....if you’re anything like me, hv plenty of paper towel and wet paper towels ready for clean up. Once all was done, no ink printed. I purged, cleaned, screwed everything back in...nothing. Then I went into maintenance and did the nozzle & head cleaning few times and it finally worked. I ran the cleaning 4-5 times. With each cleaning, it got better. Go thru each maintenance feature; cleaning, alignment, etc. That should work. Thank u for the videos! Life saver!
I'm so glad that U comment'd this! It's not onlE a process, but it's different for everEone... good job on not give'N up 💪🏿
I think I did about 10 cleanings!
Did u flush it after changing the ink ?
I appreciate this video it saved me $$$. I put the wrong ink in and then I followed this video. I only put wrong ink in the black but like a dummy I took all the ink out except the blue. so after only the blue would print. I kept doing nozzle checks, head cleaning & purges & nothing would print. I watched someone else's video & it suggested it might not be a clogg but air. he said to print with the caps open where you fill the ink. I did it & boom like magic it immediately started printing all colors. I seen a lot of people w/ the issue of not printing so thought I'd share. But thanks again for this awesome video!!!
I appreciate that so much, not onlE do we love to help. but love anE tips we can get! Thanks so much
THANK YOU, THANK YOU!! Nothing is more frustrating then your printer not printing! But because of you and your videos you have turning that around for me!! Much appreciation!
No problem at all! We troubleshoot dailE in our Facebook group: facebook.com/groups/931202507272864/
Thank you so much for this video. I searched and searched for a video to show me why my ink wasn't flowing and you helped me so much!!
ok, followed you last video on converting ET 2720 to sub. Followed you step by step. Printed out 25 pages to get old ink out. Now no printing at all. Following you on this purge video, and its WORKING...YOURE THE BOMB....
That's great... i shuldof jus pull'd ink from the dampers in the beginning 🤦🏿♂️ culdof been jus 1 video! But, we all learn'N 2gether 😅
Thank you! No one shows you this when doing the video on the change! You sir need to make from start to finish because NO ONE has that out that I have seen. Thanks again!
HopefullE this is watchu mean:
ruclips.net/video/cNsEbAT_fOk/видео.html
If so, glad we culd help!
Thank you! Between this video and a couple of others, I was able to get my converted Epson working again!
So glad we culd help
Thank you G! There are many videos telling you how to swap the ink, but non of them tell you to do what you just did. People are running head cleaning
but the lines are empty, its going to be while until you are able to see some come out. Thanks for the info.
No problem, i jus culdn't leave after the 1st video. Watchu said happen'd to me as well, gotta be honest ya kno...
Words cannot express how thankful I am for your ink swapping video and this one! Saved my dream of doing subs! :)
Glad to hear it, check us out for all sublimation products 😀
Pro tip : you can watch series at kaldrostream. I've been using it for watching all kinds of movies lately.
@Clayton Arlo Definitely, been watching on KaldroStream for months myself :)
@Clayton Arlo yup, I have been watching on kaldroStream for years myself :D
Just wanted to update you 55 sheets of regular copy paper later and 4 sublimation sheets it is printing 95% better the lines barely shows on printed images and are really faint when heat pressed.
When I cleaned the nozzle for the 22 time the nozzle check had all the black lines complete!! Thank god!!!!
Owow... see it's different for everyone! That's why I try not to make it seem like there's 1 way... glad U finallE got it tho.
I’m going to try this didn’t know I had to do this to get ink into dampers and was starting to freak out. Thank u
No problem at all, plz subscribe for more! 💪🏿
THANK YOU!!!!! I feel like you just saved my life. Your videos are always so helpful.
No problem... be sure to join our fb group: facebook.com/groups/931202507272864/?ref=share
Thanks for the great video!!! Helped us 100% We purchased your large ink and syringe kit!!
So glad we culd help! That set shuld last U awhile... #STAYPOPN
This video is extremely helpful! I found no other video showing this step! I was about to throw the damn printer out the window!! 🤣 You saved the printer and me 🤣🤣🤣
No problem, glad U got it
Thanks, this is a lot better than the other guy's video using a cleaning liquid inserted on the damper. Saving a lot of ink too. I wonder what the cause of it. It looks like air was trapped in there. I think this issue will not happen anymore after your fix and if ever it does not print in the future, it will be the printhead clogging.
Well... this happen'd to mine because i used the clean'N solution on another video 1st! It went great, i jus forgot to pull ink thru the dampers so it wuld print back normal like it never happen'd, so I jus shot this video kindof lika part 2
Why do I have lines in my pictures for I can’t seem to make them go away
I've tried some of everything! I have the et 2720. I was looking at your print how, did you get the purge page ???
Hi,what about if my tanks are full but the ink is just not going to the cartridge? Am having this problem
Hi I’m looking for one of the ink tanks for one of these et-2720. Any clue where I can get one ?
Mine will not pull through the damper but it does pull through the tube all the way back to the damper. Do I need new dampers?
your videos are awesome and have helped me alot.THANK YOU!!!!!!!
No problem at all... be sure to join the familE: facebook.com/groups/931202507272864/?ref=share
Thank you for the video, my printer works so much better, but I'm still having issues. I am still getting like dotted lines in my black and white images. I saw they are coming from the front rolls any way to prevent that. Any info is really appreciated thank you.
Help! I changed the ink in my 2750 and noticed the cartridges were empty as no ink from the lines were going into the cartridges. I followed your instructions and moved ink into the cartridges unfortunately, it’s still printing blank pages. What am I doing wrong?
What would be the reason when I am trying to add the ink back to the cartridges it’s doesn’t come out like yours I was able to follow everything but know trying to add ink to cartridges and not able too help please
Hi ..I watched your videos and switched out my epson ET2800 to sublimation ink I didn’t flush it with the cleaner. When I did my first print it only printed half the page so I did a couple nozzle checks and print cleaning and now I can’t get it to print nothing at all please help with any recommendations. Thanks
I have an Epson ET-2720 - The ink was low so I added new ink. After that I did a reset ink levels. Now the printer is not printing colors, what I mean is, it acts as though it is printing, runs through the cycle but the pages come out blank. This is what I have done... several nozzle checks, 3 head checks, I pulled the little plastic ink heads (not sure what they are called), I ran solution through them, I have re-primed the ink heads(dampers), I even sucked some of the ink out of the ink tanks to confirm they are not clogged. The printer is running right, no issues, it just won't print any of the colors. The nozzle checks are all blank, no ink on the page. Do you have any suggestions?
Thank you so much you were a lot of help! 😊
No problem... plz sub
I appreciate the help!!!🙌🏽🙌🏽
No problem at all
Can you please post a video of how to put both tabs on the left had side of the printer.
Would you happen to know, how I can safely/properly discard any ink I need to take out?
I appreciate you and your knowledge so much!!! Your saved my butt alot of money!
I discard unwant'd ink like , I do fry'N oil. I bottle it up & trash it, but if U have to, the good ole sink will work!
Awesome job my friend
Thnx
Hello first let me thank you for you videos I really appreciate you. So after the purge I did a nozzle check still printing blank what should I do ?
Resort to the purge file! I can email it over to U: nobodEbiz@gmail.com
i have a et2720 and found your videos so helpful! I was getting no cyan printing, i found this tutorial and found a leak in the damper (the plastic was coming unsealed). I tried to repair it but i was wondering if there is anywhere to buy a replacement if i can't get it to seal?
Most likelE... i will check into it for ya!
GOOD NEWS: I found the dampers & will have them available in our shop at the start of 2021!
@@nobodEbiz did you get the dampers? I’m having the same issue with my printer.
@@nobodEbiz I found the listing and just ordered 2.... can’t wait for them to arrive! I hole this fixes my issue because this printer has only been used once before this issue started.
@@AVthatsMe SAME! lemme kno
Is there a way you can recharge the ink on this printer ?
I think that is onlE available on the newer ecotank printers
Right cause on my epson et 2803 I think i need to recharge the ink for it to start printing aince i took out the old ink. Please help.
I followed steps and nothing is printing. Any ideal how to make it start printing again?
If it's still not print'N, U may of had some drawback in the lines, anE air or "clear spots" in the lines can cause this! If not, U can always try our purge method
thank you, I did exactly that and it’s up and working perfectly!! Thank you soooo much for your guidance, I have recommended your videos to several people 🙂
Could I get that purge file? I'm still not printing black.
Sure! Email us: nobodEbiz@gmail.com
It's also on our website: www.nobodEbiz.com
You saved me! Thank you!
No problem
How did u open the printer. I have struggled n I don't want to force it n break it
I show how in the 1st part: ruclips.net/video/Lp6-r7qnVT8/видео.html
Hey could you show me where those 3 flat white cables connect mine fell and disconnected and don't know where to put them
Sit'N flat, they line up with where they go! But we can fb call if ya need me: Sheddrick Arthur
Hi do you know if the same process can work for the et15000
Shuld work jus fine!
Where do I get kits to purge my ink so I can chgd to different subulation ink
www.nobodEbiz.com
I'm having problems with grid lines. I've done everything possble.
How does ur nozzle check look?
So I want to know how do I make sure that there's no more printer ink inside the Carter Ridge. And wat do I need to clean out the regular ink and put in the sublimation ink
U can always pull from the bottom of the cartridge, i figure'd this out after the video... it's easier. I also use our print head cleaner to be Xtra safe.
nobodebiz.com/products/print-head-cleaner-kit-100ml-bottle-10ml-syringe-and-tube-cleaner-cartridges-also-available
@@nobodEbiz would i be able to find that cleanser bottle in the stores
Mine brand new and has line what you think I can do
Print head clean or purge like i did N this video! U can also print that purge file
I have done many nozzle checks and my yellow, magenta, and blue still have some segments missing. Advice please.
Are there air pockets in the tubes or dampers?
Hello, do you know how to remove the ink from an EPSON ET15000?
PrettE sure it's similar, but if not, I'd be happE to help! Join our fb group: facebook.com/groups/931202507272864/?ref=share
Why my ET2720 KERP SAYING check your ink level regularly I just filled ink with all 4 colors ...what I need to do
It's jus a reminder... U good like great
So what's the best sublimation ink to use when converting the epson 2720?
color POP ink! of course: www.etsy.com/listing/802367896/epson-sublimationeco-tank-ready-color
I purchased the Epson 2760 everything went smoothly until I did the test print, 2 spaces on black lines, did nozzle clean then horizontal alignment top rectangle on all 7 have a line going through them bottom rectangle not overlapping and is blk with no lines, perfect, vertical check line #1 is not there the boxes below with #'s 1-5 each has 2 lines going through the rest of the rows 2-7 some boxes have lines some do not no matter what I do ..and 40 pages later, cleaned print head and nozzle numerous times please tell me I didn't get a lemon, I've been crying all night over this.
Plz contact me: 785-BUY-ATEE
thank you.........
no problem at all
Do you need to wait at all after your purge all the epson ink out? Before you put the sub ink in? I just got rid of all the epson ink but wasn’t sure if I should wait?
U don't... but since U did, try print'N few purge files before add'N the sub ink! If the 1st sheet is blank, I'd go straight to sub
Where can I get those big needle things? I need to get my sublimation ink out. Problem with my printer
Those are our XL syringes... we provide them here:
nobodebiz.com/products/syringe-kits
Thank you for doing this video, many times was hard to hear what you were saying but think I was able to muddle through, how-ever, when it came to the sublimation ink bottles, I couldn't see anything you were doing and this is the part I need the most. I was a dummy also and filled the ink that came with it!!! did you take plastic off the bottles that came with the printer and refill with sublim? I don't get how you were able to fill the original ink holders, did the sublin ink come with the same tops as the original bottles and fit over the cartridges to fill. I have tried syringes but does not work!!! BTW, cotton swabs would help you clean up some of the drips also and get to where paper towels does not!
I've actuallE done both methods, we sell sublimation ink & at 1st did not have the necessarE bottles with the compatible lids! So... during that time I rinse'd the originals out and jus fill'd with our color POP sublimation ink. We now have our ink bottle'd up specificallE for ecotank printers, so all U have to do is remove the seal under the cap & jus turn the bottle 180° & pour in, NO MESS! Check it out: www.etsy.com/listing/802367896/epson-sublimationeco-tank-ready-color
Can I use this method for my epson et 2760?
I don't see why not...
I did everything you did but I’m not getting it to print anything it won’t print ! What can I do to fix it?
I am having this same issue
Same here
I am having the same issue
Did U print purge files?
You are a life saver. I had to do several print head cleanings but it worked in the end. The ink is coming somewhat light though , do you think it will get darker with each printing job?
If it's now sublimation ink, this may be normal, sub ink does print more dull until its heat activate'd
I have a et 16500, would this process work the same way?
I can't say 100%, we jus got an Epson ET-16600 tho! I'll be dive'N in verE soon to see how similar the process is...
THANK YOU
No problem... Be sure to join the familE: facebook.com/groups/931202507272864/?ref=share
Do you know what could cause the paper rolls to roll, but says it’s out of paper?
Not reallE sure, but i do clean mine with alcohol wipes everE month.
I followed all your steps and I had to draw ink into the Cartlidge but now my blue is not printing can you suggest anything ??
Thank you for the help!!
Have U tried the purge file at the end? If not, we can send it over... 7852892833
What is purge file?
@@giselagarcia708 A big block'd printout of each color (CMYK), the idea is to lay down as much ink as possible to get print head clean results
@@nobodEbiz I did the purge method and still not working do you have an suggestions I can do ?
@@giselagarcia708 So... U pull'd ink thru tubes like i did in this video?
Help, My nozzle check is good but I am getting horizontal lines.
Try uncheck'N HIGH SPEED print'N! It will be under > PRINT PREFERENCES > MORE OPTIONS > bottom of page
@nobodEbiz I followed these steps and now my printer won't print.... could you help? I may have messed it up, was my first time. Great video :D
Did U follow the 1st video, or start with this 1?
hello! This is a weird question but I am trying to convert my already converted epson et2720 into a regular printer. Will this method work to take the sublimation ink out so I can put regular ink in?
Yes... doin it that way wuld be less stressful reallE! Even if a lil sub ink is left behind, it won't matter as much! This video is like part 1 & will help more: ruclips.net/video/Lp6-r7qnVT8/видео.html
How did you open this printer top?
ruclips.net/video/Lp6-r7qnVT8/видео.html
It looks like I have a little bit of epson ink still in my printer. How can I remove it or can I add sublimation ink and it will be ok? I also put the printer cleaner through.
U use'd print head cleaner & still have ink N there?
@@nobodEbiz same here like ill print purge pages and they are still printing color
Hey do u think u can help me? My printer stopped picking up paper randomly! ET 4700. I had the scanner code thing and I fixed that but now my printer wont pick up paper. All from a damn paper jam! This is a design flaw for sure... but anyway lmk if u can help possibly plzzz!
Ok... now I see! U may need to damp ribbon roll ur rollers. This help clean & free up debris
Where can I buy replacement dampers? My yellow isn't printing. I think I messed it up.
We have them available... update'N shop 2day 💪🏿
Update'd: www.etsy.com/listing/947069175/replacement-ecotankchipless-software
After i removed the epson ink, what do i do next? I followed the syringe video and extracted the epson ink. How do i start with the sublimation ink? Whats the next step?
Either... clean out with printhead cleaner, or choose not to & add the correct ink and run the purge method until U notice a change
How do I remove the lid. I cant find a video that shows me that
Follow part 1: ruclips.net/video/Lp6-r7qnVT8/видео.html
I converted my printer into sublimation. Unfortunately it just prints blank pages. My printer sounds like its printing but nothing. Can you please help me.
I have the same problem did you ever get it fixed??
Did U try print'N purge files? U can also doba ink flush
Did u flush it after changing the ink ?
Yes... on our 1st video
Can I somehow take out the regular ink and replace with Sublimation Ink on my Epson 2720? I love your videos by the way.
Thank U!!! & U sure can... here's how I did: ruclips.net/video/Lp6-r7qnVT8/видео.html
@@nobodEbiz thank you so much
@@shawnminarik4936 not a problem
any idea why after doing this my printer acts like its printing but no image gets on the paper??
Follow part 2: purge the lines! This happen'd to me as well
My niece put a little of yellow sublimation ink on the black side and now after I put the black sublimation ink with the yellow , the printer won’t print black. What should I do? Thanks
Try to retract & cleanout! Here's how: ruclips.net/video/Lp6-r7qnVT8/видео.html
Thank you!!!
@@ligiahan9105 no problem... lemme kno if U get it
Where is the purge file?
On our website: www.nobodEbiz.com
Thank you so much! I appreciate you!
What’s the link to your shop?
www.nobodEbiz.com
www.etsy.com/shop/nobodEbiz
I did everything exactly like you and the ink still not printing on the paper what can I do?
U can always re-pull ink thru the dampers, U may have had some drawback! Also... the print purge file method is a process, i do 25 prints, then a print head clean, if it still needs work... i repeat
Have you ever had an error 100077 come up on the printer screen after lifting the cover/top off?
No i haven't, I can search around tho
Happened to me you unplugged something! I followed a video about scannner er2 and was able to get it fixed however now have another issue... this is a real design flaw in the ET series!!
@@kristenroma7833 I jus post'd wat i did
Where is the purge video mine printed first time but not now
This is the purge video... do U mean the file?
What kind of syringe is that?
Our XL syringes: nobodebiz.com/products/syringe-kits
just unboxed 2720 put sublimation ink in and i don’t get no ink coming out when i do nozzle check
I'm having the same issue, have you figured it out yet?
@@lesliejansen2330 i did a power cleaning
This purge'N cam help as well
I did this and now it’s not printing at all....it acts like it is then it’s just a blank page ... any suggestions or do you know what I did wrong ?
Continue print'N the purge file... if U need it, U can find it on our website: www.nobodEbiz.com
I don’t want to break it how do I open the top?
First minute or two: ruclips.net/video/Lp6-r7qnVT8/видео.html
Both of the ribbon came out for me and I’m still getting the error message
Were they replace'd?
I have done everything the 2 videos said to do it still won't print
Are there NE air bubbles N ur tubes?
Basically you just need to prime the tubes once you’re done
Yea... i forgot to on my 1st video 😅
I switched out my ink now it don’t print?
U may need to purge like i did: ruclips.net/video/EvgrxWGwNug/видео.html
We followed both your videos and no ink is printing. We have no idea what the problem is - any help you can offer?
Wow afraid to do this, hope you get help, Sure there's an answer, but would like to know also, Good Luck
Was there any drawback wen U pull'd the ink?
I hope mines work after I do this when I get off work I will let you know
It worked but not I have to purge everytime my cartridges run out of ink
@@msmikared1 U shouldn't have to, i purge'd once after doin the switch and its been fine!
I cleaned out my regular ink, purged what was left, and now my printer won’t print. There’s no ink going onto the paper. Where did I go wrong??
Culd jus need to print purge files like i did at the end of this
@@nobodEbiz thank you for responding. I’ve been print purging since last night and still nothing. I even pulled some ink through the tubes and still nothing.
@@DiamondLeann did you solve it mine is not printing either
@@Iamangiesanchez9 No. Not at all. I got completely frustrated and fed up so I purchased another printer.
So after doing this my printer don’t print at all 😔 what did I do wrong how can I fix it
Wat is it say'N? Need more details...
Same here nothing prints out 🤦🏽♀️ not sure if i did this wrong
Did everEone print the purge files like i did? U gotta remember that this is process, not a step by step solution, the time'N on all of ur results will differ... also, the other ink is still run'N thru the print head... these videos onlE clear'd up the dampers & tanks! I do about 25 sheets of the purge file on premium presentation matte or glossE settings, jus to lay down more ink! Then I run a print head clean. Repeat until I'm back on track with either the file or my nozzle check.
@@nobodEbiz what r purge files
@@kaitlynhubbell7496 The big CMYK I was print'N out towards the end! I have a post on here with it
Can I email you? Trying to troubleshoot and I am having no luck.
That our find me N our FB group: facebook.com/groups/931202507272864/?ref=share
*I'm here dailE 😄
I changed my ink and added my sublimation and it’s not printing
blank pages?
Same problem I'm having blank pages
Same here blank pages
Did everEone print the purge files like i did? U gotta remember that this is process, not a step by step solution, the time'N on all of ur results will differ... also, the other ink is still run'N thru the print head... these videos onlE clear'd up the dampers & tanks! I do about 25 sheets of the purge file on premium presentation matte or glossE settings, jus to lay down more ink! Then I run a print head clean. Repeat until I'm back on track with either the file or my nozzle check.
Can't see what you're doing when your back is in the way, Just saying, I've never cleaned an epson before so I need to see what you're doing. I have no idea if you removed anything or added somethings??????
I did the same thing 4 times, once per color, but wat XactlE are U stuck on? Maybe i can help
My printer not printing at all now 😭
U may need to purge like i did: ruclips.net/video/EvgrxWGwNug/видео.html
I Did This And It’s Still Not Showing Up 🤬🤯😡
It's a process... i repeat til i fix rhe issue
Omg I’m dying over here while I was purging my top to my printer fell and the tape on the left side came off 😭
It slides back in... i kindof did this & got a 100016 code 😱
Same thing happened to me. Flip the printer around and use tweezers to put them back into their slots
Check it out: ruclips.net/video/I_YM35KrC44/видео.html
Thank you... Mine was successful after watching this👆👆👆
That's watsup 😁
I just want to give up already
Wat's goin on?
I'm just gonna run my ink out then fill it then purge until I get the perfect quality this is a bit too much
Yea, this is 2 much, I jus put the correct ink in mine from the jump 🤷🏿♂️
Also my printer was printing perfectly fine until this paper jam. this is a bad time for this cuz i already refunded nearly 1k in these coupleday :( fml
I'm unfamiliar with the paper jam U talk'N... wat happen'd?
I still can't get mines to print idk what's wrong so frustrating
AnE bubbles N the tubes?