I have a 2007 corolla with code po741 is a solenoid the transmission makes the changes very well the rpm works normal. replace solenoid but engine light returned. I need help that I must do to repair that problem. Thank you
Car jerks at times when shifting from 2-3 gear and sometimes gets stuck in 3rd what could it be ive replaced the input speed sensor code and it still says the same code and the issue is still there
I HAVE A TOYOTA CAMRY 98 V6 , WHEN TRANSMISSION IS COLD IT TAKES TIME TO GET TO 1ST GEAR AND OTHER GEARS ITS SLIPPS, BUT ONCE ITS WARMED UP IT SHIFTS ALL GEARS PERFECTLY HELP PLEASE
I have poor acceleration and I can't reverse. The transmission fluid was terrible. I cleaned pan, got new filter, topped it off and it still keeps slipping and not accelerating. I also can't reverse. Do I need a new solenoid? What are other probable causes?
Hi Peter. Thank you for your direct to the point videos. Much appreciate it. My 2000 Camry with 5S-FE has an automatic. When it's cold, it shifts a bit jerky from 1st to 2nd gear and after it gets warm, I don't notice it anymore. Downshifting is fine for all gears. this only happens for up shifting from 1st to 2nd gear. Help please.
Hey my Toyota Camry has a problem where is doesnt shift from 2nd gear into 3rd it’ll just rev up and continue in 2nd gear would this be a solenoid problem?
My 2000 Camry 2.2L, I drove without transmission fluid like ten feet, the transmission started to smoke, I parked it, did a transmission fluid and filter change, then I tried to reverse, but reverse didn’t work anymore, and also, when I put in neutral it acts like it’s in drive, it drives perfect but I some how messed up reverse bc I don’t have R no more . Any clue how to get R back ?
Can a bad reverse solenoid in a 2002 Camry cause reverse and neutral to act like park? All drive gears work as expected. The console shows the correct gears, and the engine/transmission sounds seem to be like normal when shifting into reverse and park, but the performance is that of being in park. I can't even reverse the vehicle at all... there is no neutral at all.
Hi. I have a camry 2003 v6 and the car clunk when shifting back to first gear. It also clunk when i put into reverse from park or drive. Amy idea? Thanks
Hello, I have a 1992 celica 2.2L automatic transmission, when I shift into reverse the car will not move, and when I shift into neutral the vehicle moves forward, can you please give me some advice on which steps I should take first, figuring out what’s wrong with my transmission thank you.
You have a gearbox fault. The problem could be helped by changing the oil Ford type F. And then disconnecting the gear cables, lubricating them and installing them back
Hi Peter. I have camry 2013 car accelerates slowly. sometimes it doesnt shift at all and sometimes it starts in third gear and doesnt shift up or down unless I turn it off while running put on N the start then put on D and it goes fine and shifts up all 6 gears. Then when I decelerate and stop at traffic light it starts all over again and I have to repeat the trick again .. very annoying 😥
Hi Peter. i got camry 2003 model (acv30). the problem is when the engine is cold and i shift the gear to D it wont move. its either i leave it idle for 10 to 15 mins or rev it up until jerking can only the car move. is it solenoid problem ? ive try changing the oil and filter still same issue,
Hello and thank you for the message. I think that your automatic box has a problem, maybe the oil pump and the clutch plate, you should do a complete interior repair Automatic box new or buy a used box junkyard buy
I got my new selonoids No 1 & 2, but they came with a ground wire with them. Can I ground the wire somewhere inside the tranny? Or can I just connect the selonoid connectors and leave the ground wire alone? Thank you!
Hi Peter, I have 2000 Camry V6 3.0 with check engine code P0773 (shift Solenoid E electrical). Your video watched if i replace it would be fine and no code? I don't have a gear or shifting problem that I can feel driving. Thank you.
what would be the symptoms if the solenoid are failing? I've had an issue for about three years where my Sienna van will not shift from second into third until it warms up a little. shifts fine after except for a rare hard shifting which may be due more to a bad motor mount. no CEL codes and has not gotten worse since I bought the van. I think previous owner was setting trans fluid level with car off instead of running so he ran it with less oil than needed for a while. when I bought it, it would make a strange humming noise at start up that went away after a couple minutes. after I changed the oil and filter and corrected the level, it stopped making the noise at start up but still hesitates on shifts until warm. ideas?
Originally, I was thinking along the same lines but if it was a wear-and-tear item, wouldn't you expect it to get worse over time? The symptoms have not changed in 3 years.
My car goes from first gear to fourth skipping 2 and third gear. But it does work when I shift it into dr-1and dr- 2 on the stick. Do I need to replace both of these soliniods. Best because I'm in there do you think sir? Thank you for the advice.
2002 camry will shift normally with light throttle, But wont shift until4000-4500 rpms under normal throttle. Or until i let off the accelerator. The tranny level is about 3/8 inch below the lower hot mark when engine is warmed up. Is this model that sensitive to fluid level? It shifts just fine into drive or reverse. 231000 miles. fluid probably never changed.
My 2008 Camry had a leaking gearbox issue. So I went to the mechanic and he said he needed to open the gearbox and apply some seals and gasket. After putting it back now the gears are slipping and last night it slipped and now not able to shift into D,4,3,2,L. It goes into R and P only. What would be the problem?
@@PeterFinnTheCarDoctor is it very tough to be replaced? These mechanics forced me to replace my entire gearbox saying that after repairing it there is no guarantee that it will be fixed.
Good Day Mr. @Peter Finn I do have 2007 toyota camry v6 3.5l. with codes P0500, P0717 And P0746. and the car does not move at all. I'll need to rebuild the entire transmission ? Thanks in advance.
i have a '92 with a 3sfe ,transmission was all good( went in all gears) (been parked in my slanted drive way for some time) ,all of a sudden one day i removed it back 4 feet ,and now it doesnt go into gear at all,just makes a grinding noise when trying to shifting the lever into gear(cable is well connected),is my tranmission gone?
( from the caribbean ) hey i have a 1998 toyota corolla it shifts fine on level roads but when i go up hills it gets slow before it goes into low gear ,what can be the problem changed the fluied an strainner already
I have toyota yaris automatic transmission 2011 ..it have problem that when gear shift to D..or Rivers..an effect like jumping..that is lack of clutch...
so I have a 1993 Toyota Camry but it seems it won't go in reverse you can feel it kick in once you put in reverse but won't back up. all the other gears i put it in work but reverse can you help
How many shift solenoid a transmission has? Is it inside transmission for Japan made version Camry? My 1999Toyota Camry V6 XLE is Japan made. It has fault code P0773 because shift control solenoid failed, and engine light on. I try to locate this shift solenoid without luck. Another You Tube page from Jeremy Hood that shows 99 Camry has shift solenoid behind Automatic transmission 3 ways Switch Assembly, Neutral Start. It is mounted on transmission outside , right below car battery area. I am very thankful if anyone can help me.Thank you.
In case someone sees this in future, the three solenoids are in the transmission. Drain the transmission then remove the pan to access them. There are three. Two wired together, solenoids one and two then the third is the lock out solenoid or the shift solenoid 'e' by itself.
I have been having issues with the automatic transmission of Toyota camry 1997 model , I have taken it to obd for diagnosis it shown only cam shaft sensor and it will shift from 1st to 3rd gear instead of 1st to 2nd and it will be revolving at 6000rpm at 20mph kindly assist on it
Peter Finn hello. my 2.2 camry shifts hard. when I leave a stop it stays in 2nd and drives slow and then all the sudden it drops gear and accelorates fast. what is the problem please?
hi Peter I had a question if you don't mind me asking. my check engine light is on for my 2008 Toyota Corolla. the code is p0741 and it says that it's the torque converter lockup solenoid. when I asked a mechanic they said that I would need to change the torque converter but since I would change that might as well change the transmission. anyways their trying to charge me like $3000 but I don't think it's the torque converter I think it's one of the actual solenoids connecting to the torque converter. what do you think it could be?
Hi. You mentioned solenoid 1. Is that 1st gear solenoid? I have an 2000 corolla with trouble shifting on first gear to second gear. Revs up at take off. Was that the first gear solenoid you pointed at at first?
So my Automatic transmission Toyota caldina wagon gear lever can move in D,R,P and N position, However the car does not move. I changed the ATF and it was very dirty with lots of sludge. I did 2 to three refills and draining the ATF and cleaning transmission filters and solenoid. And now the car moves a bit but then stops. When I press the accelerator pedal car wont move.
Hey I have a 2002 Camry 3.0,everything works fine until I get up to third and have to switch to fourth gear,itll shift as long as I keep the rpm below 2 but it has no power so it's slow getting up to speed that way could solenoids be the issue?
Hello Peter, my name is Yuan. I have a 1994 Toyota Camry LE V6. Recently it showed up an Engine Check problem exactly identical to what Dacari described in his question, with OBDII code of P0773 which pointed to Transmission Shift Solenoid E problem. I am lucky to find your article about how to trouble shooting and fixing the problem. It took me a lot of time to go into the transmission pan and finally found the Shift solenoid E. As mater of fact, I tested all 3 solenoids in the pan. They all pass the Resistant measurement test and Voltage click tests. I ran out of ideas, so I put them back as close as possible. The car still runs. But when the RPM reaches above 2200 RPM, or Speed above 50 miles, the Engine Check turns on with O/D OFF flashes. Can you tell me any other solenoid might be in problem ?
Hello Sir.. I just put 800 in a engine rebuilt but my transmission started slipping little by little now just continuously slips reverse is great but first is gone it feels like I changed fluid and filter no metal or anything just old nasty fluid.. im begging help I can't afford a soft parts rebuild they want 1200 that's crazy.. im decent mechanic I can do tie rods ball joints wheel bearing but don't think I can handle a transmission
Hi, I have a 95 Toyota Corona with garbox problem. I wonder how many selenoids are 95 Toyota Corona 4-speed automatic gearbox have, and do you know is it similar with Camry's gearbox? My gearbox has a problem, it steps over 1st and 3rd gears immediately to 2nd and 4th gears. And also it do not evaluate kick-down . A forum-mate said I should replace 1st selenoid, and I want to do this on my own. Can you give advices about my stuation please, regards.
hye boss... I have a Camry 5s 2.2 car... all the gears can go in but I can't run... before that the gearbox pump gear broke so it has been replaced but it still can't run...car auto...
Hey I see and noticed you've posted a lot of Toyotas you worked on . Question my car can go reverse but won't move on D nor any other gears. I've added more transmission fluid nothing any suggestions?
Wow, apparently this is a pretty international car. My pastor let me borrow his while I crashed my 350Z. I'm trying to do him a solid and get rid of this check engine light.
Sir, Thankyou for your vids. 2003 Camry, auto trans slip, in reverse gear, up steep driveway. Trans flushed & filter screen changed. Maybe better, but still slips sometimes. Managing by handbrake start, in reverse, up incline. Revving a little, seems to apply the rev clutch pack better? Should the rev solenoid be replaced? Even if the trans is a bit old, Reverse gear is the least used? Which solenoid is for rev gear - U241 E?
Good day. i have a 2003 Toyota Camry that previously had an accident. since then the gear only changes gear 1,2,3 cant change to 4 and 5. i have changed to another gear box. the same problems. i feel its electrical problem. please can you advice me on what to do. i cant enjoy the car. looking forward to your reply.
Thank you! The grace and the peace be with you from The Lord your God our father and how many of you know about the good news repent and believe in the gospel because the kingdom of heaven is at nigh and you believe in him son Jesus? Mark 1:15 Matthew 10:7 Luke 10:9 John 5:39
Really tnx ,,,I have land cruiser 2005 8v 4.7,,,errors p0985 p0986,,but which solenoid I should change ,,,while there are 8 sensors there 😂 ???? And how to change oil where there is no oil Gage ??😂😂😂
1997 TOYOTA ALAVON TRANSMISSION WILL GO INTO REVERSE AND PULL CAR BACKWARDS, BUT WONT GO INTO DRIVE AND PULL CAR FORWARD,I CAN FILL TRANSMISSION GO INTO DRIVE BUT WONT PULL CAR FORWARD
I have a 2007 corolla with code po741 is a solenoid the transmission makes the changes very well the rpm works normal. replace solenoid but engine light returned. I need help that I must do to repair that problem. Thank you
Hi. If either one isn’t working, would that make the car not move when put in gear? Thanks
👍
This 5 solenoids inside the gearbox how get the power .Which wire outside the gearbox supply solenoids with power
Noted 👍
So which one is a Shift solenoid A?
Thanks 😀👍
nice simple video..thanks from Malaysia
Thanks. :-)
Car jerks at times when shifting from 2-3 gear and sometimes gets stuck in 3rd what could it be ive replaced the input speed sensor code and it still says the same code and the issue is still there
I have read your message, Thank you 😀👍 Please Join my member.
I HAVE A TOYOTA CAMRY 98 V6 , WHEN TRANSMISSION IS COLD IT TAKES TIME TO GET TO 1ST GEAR AND OTHER GEARS ITS SLIPPS, BUT ONCE ITS WARMED UP IT SHIFTS ALL GEARS PERFECTLY HELP PLEASE
Replace fluid
I have poor acceleration and I can't reverse. The transmission fluid was terrible. I cleaned pan, got new filter, topped it off and it still keeps slipping and not accelerating. I also can't reverse. Do I need a new solenoid? What are other probable causes?
Hi, replace Ford type F fluid
Please car doctor, my Toyota Highlander, driving only front and the revice is not working. Is not going back. Solution please.
Noted
Hey where can I locate the clutch solenoid in my 2004 Toyota Camry?
Torque converter clutch solenoid location please.
Same area
Hi Peter. Thank you for your direct to the point videos. Much appreciate it.
My 2000 Camry with 5S-FE has an automatic. When it's cold, it shifts a bit jerky from 1st to 2nd gear and after it gets warm, I don't notice it anymore. Downshifting is fine for all gears. this only happens for up shifting from 1st to 2nd gear.
Help please.
Thanks for sharing
@@PeterFinnTheCarDoctor you're welcome:)
Could you tell me if jerky shifting at cold start is Ok?
Hey my Toyota Camry has a problem where is doesnt shift from 2nd gear into 3rd it’ll just rev up and continue in 2nd gear would this be a solenoid problem?
Maybe worn out clutch plates
Great video . Can you tell me what solenoid dose what gear as my 3rd gear shirt is odd ? Thanks
Let me check....
I’m having the same issue going into third gear
My 2000 Camry 2.2L, I drove without transmission fluid like ten feet, the transmission started to smoke, I parked it, did a transmission fluid and filter change, then I tried to reverse, but reverse didn’t work anymore, and also, when I put in neutral it acts like it’s in drive, it drives perfect but I some how messed up reverse bc I don’t have R no more . Any clue how to get R back ?
Thanks for sharing 👍😀
Sir can you please mention the shift solenoid part number.
Noted 👍
Sir Please give your email
I have a 1992 Lexus LS 400 it seems to shift from 1st to 3rd would replacing the solenoids work
Thank You. :-)
Can a bad reverse solenoid in a 2002 Camry cause reverse and neutral to act like park? All drive gears work as expected. The console shows the correct gears, and the engine/transmission sounds seem to be like normal when shifting into reverse and park, but the performance is that of being in park. I can't even reverse the vehicle at all... there is no neutral at all.
Message read, good comment 👍
Will a bad solenoid cause car not to go into drive but reverse ?
Yes
Which solenoid is it?
Which of them
Hi Peter I have a 1997 camry the reverse doesn't work any tips?
Yes, replace fluid to Ford fype F
Hi. I have a camry 2003 v6 and the car clunk when shifting back to first gear. It also clunk when i put into reverse from park or drive. Amy idea? Thanks
Hi, your gearbox is worn out. Please replace better gearbox.
motor mounts/transmission mounts👌
Hello, I have a 1992 celica 2.2L automatic transmission, when I shift into reverse the car will not move, and when I shift into neutral the vehicle moves forward, can you please give me some advice on which steps I should take first, figuring out what’s wrong with my transmission thank you.
You have a gearbox fault. The problem could be helped by changing the oil Ford type F. And then disconnecting the gear cables, lubricating them and installing them back
Hi Peter. I have camry 2013 car accelerates slowly. sometimes it doesnt shift at all and sometimes it starts in third gear and doesnt shift up or down unless I turn it off while running put on N the start then put on D and it goes fine and shifts up all 6 gears. Then when I decelerate and stop at traffic light it starts all over again and I have to repeat the trick again .. very annoying 😥
Ok, how much km ?
@@PeterFinnTheCarDoctor 200000
Hi Peter. i got camry 2003 model (acv30). the problem is when the engine is cold and i shift the gear to D it wont move. its either i leave it idle for 10 to 15 mins or rev it up until jerking can only the car move. is it solenoid problem ? ive try changing the oil and filter still same issue,
Hello and thank you for the message. I think that your automatic box has a problem, maybe the oil pump and the clutch plate, you should do a complete interior repair Automatic box new or buy a used box junkyard buy
I got my new selonoids No 1 & 2, but they came with a ground wire with them. Can I ground the wire somewhere inside the tranny? Or can I just connect the selonoid connectors and leave the ground wire alone? Thank you!
Yes
To removw the pan its 10 mm bolts?
Yes
Hi Peter, I have 2000 Camry V6 3.0 with check engine code P0773 (shift Solenoid E electrical). Your video watched if i replace it would be fine and no code? I don't have a gear or shifting problem that I can feel driving. Thank you.
Glad it helped
What wires on the outside of the tranny control the torque converter lockup? I want to wire in a lockup switch but cannot find any information. Thanks
Good comment. 😀👍
what would be the symptoms if the solenoid are failing? I've had an issue for about three years where my Sienna van will not shift from second into third until it warms up a little. shifts fine after except for a rare hard shifting which may be due more to a bad motor mount. no CEL codes and has not gotten worse since I bought the van. I think previous owner was setting trans fluid level with car off instead of running so he ran it with less oil than needed for a while. when I bought it, it would make a strange humming noise at start up that went away after a couple minutes. after I changed the oil and filter and corrected the level, it stopped making the noise at start up but still hesitates on shifts until warm. ideas?
Hi, your transmission clutch discs might be worn out
Originally, I was thinking along the same lines but if it was a wear-and-tear item, wouldn't you expect it to get worse over time? The symptoms have not changed in 3 years.
@@LibertarianCoconut 4 years later you ever figure it out?
excellent video, tank you sir,😎
Thank You for comment. Best Regards Peter Finn
@@PeterFinnTheCarDoctor so which one is the shift solenoid A?
My car goes from first gear to fourth skipping 2 and third gear. But it does work when I shift it into dr-1and dr- 2 on the stick. Do I need to replace both of these soliniods. Best because I'm in there do you think sir? Thank you for the advice.
Hi, you need a new gearbox
yes i have a 97 Camry it will go in reverse but one Drive ...can it be a Bad solenoids
Maybe bad clutch plates inside
2002 camry will shift normally with light throttle, But wont shift until4000-4500 rpms under normal throttle. Or until i let off the accelerator. The tranny level is about 3/8 inch below the lower hot mark when engine is warmed up. Is this model that sensitive to fluid level? It shifts just fine into drive or reverse. 231000 miles. fluid probably never changed.
Thanks for info 👍
@@PeterFinnTheCarDoctor i was wondering if you had any ideas on my very high rpm shifting
My 2008 Camry had a leaking gearbox issue. So I went to the mechanic and he said he needed to open the gearbox and apply some seals and gasket. After putting it back now the gears are slipping and last night it slipped and now not able to shift into D,4,3,2,L. It goes into R and P only. What would be the problem?
Hi, your gearbox clutch plates are worn out
@@PeterFinnTheCarDoctor is it very tough to be replaced? These mechanics forced me to replace my entire gearbox saying that after repairing it there is no guarantee that it will be fixed.
hi.. I have a Toyota Corolla 2002 model. it delays when shifting from gear 1 to gear 2 and it's automatic.what could be the issue
Please replace new transmission oil
Peter Finn I have done that and no improvement. I put it in a computer for diagnosis and reported A solenoid and B solenoid also...what should I do
Erick Maina hi did you replace the 2 in the front after taking off the pan? I have a a& b code to
Good Day
Mr. @Peter Finn
I do have 2007 toyota camry v6 3.5l.
with codes P0500, P0717 And P0746. and the car does not move at all. I'll need to rebuild the entire transmission ?
Thanks in advance.
Hi, please replace:
Vehicle Speed Sensor
This could help you !
Look my video: ruclips.net/video/Q3Q7KR6rMZY/видео.html
BR
PETER
Show less
i have a '92 with a 3sfe ,transmission was all good( went in all gears) (been parked in my slanted drive way for some time) ,all of a sudden one day i removed it back 4 feet ,and now it doesnt go into gear at all,just makes a grinding noise when trying to shifting the lever into gear(cable is well connected),is my tranmission gone?
Thanks for sharing, please try replace new oil to transmission
@@PeterFinnTheCarDoctor thanks ,will give you an update
Got the transmission off ,how much oil does it take to refill
Which one is solenoid E??
Thanks for comment. 👍😀
Where did you get those two Solenoids?
Toyota Dealer spare parts
@@PeterFinnTheCarDoctor Toyota dealer spare parts
Thanks
( from the caribbean ) hey i have a 1998 toyota corolla it shifts fine on level roads but when i go up hills it gets slow before it goes into low gear ,what can be the problem changed the fluied an strainner already
Maybe oil replace helps
I have toyota yaris automatic transmission 2011 ..it have problem that when gear shift to D..or Rivers..an effect like jumping..that is lack of clutch...
Thanks for comment. 👍😀
Hi Peter, My son's 2002 Camry 4cyl shows P0765 shift solenoid D. Where is the solenoid located and which one is it if there is more than one? Thanks
Hi, please replace fluid to Ford Type F fluid. It could help you.
@@PeterFinnTheCarDoctor OK, I will try. thanks
1991 camry my car drives but is loud. Also speedometer does not work until after 20 mph then needle jumps. What can be problem??
may be the speed sensor.
It may be loud because of an exhaust leak. If it sounds like its pushing air out making a kind of "F" sound, that is more than likely the case.
Does this apply to the v6 model or only the 4 cylinder model?
Both
Do we have to drop the pan to get to the solenoid??
Yes, you need to remove the pan and filter to access the valve body, where the solenoids are located.@@getdagist1
What would the part number be for the number one solenoid for a 93 v6 Camry
so I have a 1993 Toyota Camry but it seems it won't go in reverse you can feel it kick in once you put in reverse but won't back up. all the other gears i put it in work but reverse can you help
Hi, plese do this:ruclips.net/video/7ZqAwY5Pfao/видео.html
okay thanks i'll give it a try
lord mohr
How many shift solenoid a transmission has? Is it inside transmission for Japan made version Camry? My 1999Toyota Camry V6 XLE is Japan made. It has fault code P0773 because shift control solenoid failed, and engine light on. I try to locate this shift solenoid without luck. Another You Tube page from Jeremy Hood that shows 99 Camry has shift solenoid behind Automatic transmission 3 ways Switch Assembly, Neutral Start. It is mounted on transmission outside , right below car battery area. I am very thankful if anyone can help me.Thank you.
Hi, sorry. I don't know V6 gearbox.
Did you ever find out how.to.fix the solenoid and how much did cost??
i have the same.make and model
1999 toyota camry v6
In case someone sees this in future, the three solenoids are in the transmission. Drain the transmission then remove the pan to access them. There are three. Two wired together, solenoids one and two then the third is the lock out solenoid or the shift solenoid 'e' by itself.
How long does it take
👍
Is this on a six cyl motor
4
@@PeterFinnTheCarDoctor thankyou. I may attempt this job. I love you attitude.
I have been having issues with the automatic transmission of Toyota camry 1997 model , I have taken it to obd for diagnosis it shown only cam shaft sensor and it will shift from 1st to 3rd gear instead of 1st to 2nd and it will be revolving at 6000rpm at 20mph kindly assist on it
Ok, You need to replace new oil to gearbox
thank you comrade very helpful
Great ! And Thanks for feedback. :-)
Peter Finn hello. my 2.2 camry shifts hard. when I leave a stop it stays in 2nd and drives slow and then all the sudden it drops gear and accelorates fast. what is the problem please?
how do you know which sylinoid is for the fourth gear?
Hi, I need to do new video in future. :-)
I have a 2000 Toyota solara that will not go in reverse but all other gears work what could be the problem
Maybe oil replace could help or gearbox clutch replace
hi Peter I had a question if you don't mind me asking. my check engine light is on for my 2008 Toyota Corolla. the code is p0741 and it says that it's the torque converter lockup solenoid. when I asked a mechanic they said that I would need to change the torque converter but since I would change that might as well change the transmission. anyways their trying to charge me like $3000 but I don't think it's the torque converter I think it's one of the actual solenoids connecting to the torque converter. what do you think it could be?
Hi, first replace new transmission oil and fluid. This service helps often ! Visit the Toyota dealer, because they use special transmission fluid.
Hi. You mentioned solenoid 1. Is that 1st gear solenoid? I have an 2000 corolla with trouble shifting on first gear to second gear. Revs up at take off. Was that the first gear solenoid you pointed at at first?
Hi, sorry. I need to do new video.
So my Automatic transmission Toyota caldina wagon gear lever can move in D,R,P and N position, However the car does not move. I changed the ATF and it was very dirty with lots of sludge. I did 2 to three refills and draining the ATF and cleaning transmission filters and solenoid. And now the car moves a bit but then stops. When I press the accelerator pedal car wont move.
Hi maybe your automatic transmission clutchs are worn out. You need replace those ! Look my info video: ruclips.net/video/U5BzUDJEciE/видео.html
Thanks alot let me check it out
hi peter, i have a 1993 camry automatic that wont down shift with throttle , but work fine when cruise controls on, got any ideas?
MAybe transmission oil replace helps...
Hey I have a 2002 Camry 3.0,everything works fine until I get up to third and have to switch to fourth gear,itll shift as long as I keep the rpm below 2 but it has no power so it's slow getting up to speed that way could solenoids be the issue?
Yes
a340e auto not changing to 4th gear. help!
Hi, have You replace transmission oil when?
Dunno. Just got this car 2 weeks ago.
and also odometer and speedometer not working.
can bad solenoid cause transmission slipping?
Yes
How the fuck do you fix trans by watching this?
Hello peter I have a 94 Camry that the O/D flashes then check engine light comes on. Would that be my shift solenoids? Thank you.
MAybe gearbox oil replace helps
your overdrive band is no good!!! dont listen to this guy!
Hello Peter, my name is Yuan. I have a 1994 Toyota Camry LE V6. Recently it showed up an Engine Check problem exactly identical to what Dacari described in his question, with OBDII code of P0773 which pointed to Transmission Shift Solenoid E problem. I am lucky to find your article about how to trouble shooting and fixing the problem. It took me a lot of time to go into the transmission pan and finally found the Shift solenoid E. As mater of fact, I tested all 3 solenoids in the pan. They all pass the Resistant measurement test and Voltage click tests. I ran out of ideas, so I put them back as close as possible. The car still runs. But when the RPM reaches above 2200 RPM, or Speed above 50 miles, the Engine Check turns on with O/D OFF flashes. Can you tell me any other solenoid might be in problem ?
Hello Sir.. I just put 800 in a engine rebuilt but my transmission started slipping little by little now just continuously slips reverse is great but first is gone it feels like I changed fluid and filter no metal or anything just old nasty fluid.. im begging help I can't afford a soft parts rebuild they want 1200 that's crazy.. im decent mechanic I can do tie rods ball joints wheel bearing but don't think I can handle a transmission
Hi Sir, your transmission clutch plates are worn out. :-( So, you need new clutch plates or new gearbox. Maybe low miles used?
Hi, I have a 95 Toyota Corona with garbox problem. I wonder how many selenoids are 95 Toyota Corona 4-speed automatic gearbox have, and do you know is it similar with Camry's gearbox?
My gearbox has a problem, it steps over 1st and 3rd gears immediately to 2nd and 4th gears. And also it do not evaluate kick-down . A forum-mate said I should replace 1st selenoid, and I want to do this on my own.
Can you give advices about my stuation please, regards.
Hello, I am planning to do new video on Corolla automatic gearbox.
For what year and model??
hye boss... I have a Camry 5s 2.2 car... all the gears can go in but I can't run... before that the gearbox pump gear broke so it has been replaced but it still can't run...car auto...
Sounds bad. Buy a good old engine and gearbox cheap. And change parts for your car. Parts can be found in some junkyard.
Thank for information boss...
Hey I see and noticed you've posted a lot of Toyotas you worked on .
Question my car can go reverse but won't move on D nor any other gears.
I've added more transmission fluid nothing any suggestions?
Hi, do you mean gear stick. It not go to D ?
It goes to the D shift but does not go foward
Ok, then you might have mechanical failure in gearbox
Wow, apparently this is a pretty international car. My pastor let me borrow his while I crashed my 350Z. I'm trying to do him a solid and get rid of this check engine light.
What about v6 3.0 my code is po770
Thanks 👍😀
I have a 2004 4 cyl Toyota solara engages gears for a short time then feels like the car is in the nuetral after awhile from being on
Ok, maybe gearbox oil replace could help
Also has the p0741 code. Would I have to change the torque converter clutch circuit as well ?
Sir, Thankyou for your vids. 2003 Camry, auto trans slip, in reverse gear, up steep driveway. Trans flushed & filter screen changed.
Maybe better, but still slips sometimes. Managing by handbrake start, in reverse, up incline. Revving a little, seems to apply the rev clutch pack better? Should the rev solenoid be replaced? Even if the trans is a bit old, Reverse gear is the least used? Which solenoid is for rev gear - U241 E?
Thanks ! Good comment. 😀👍
thanks Peter ...
Thanks. :-)
WHAT DO U HAVE TO REMOVE TO GET THE SENSORS OUT???
سلام عليكم شفر بلاندر عندي عطل بالكير
Good day.
i have a 2003 Toyota Camry that previously had an accident.
since then the gear only changes gear 1,2,3 cant change to 4 and 5.
i have changed to another gear box. the same problems. i feel its electrical problem.
please can you advice me on what to do. i cant enjoy the car.
looking forward to your reply.
Thank you!
The grace and the peace be with you from The Lord your God our father and how many of you know about the good news repent and believe in the gospel because the kingdom of heaven is at nigh and you believe in him son Jesus?
Mark 1:15 Matthew 10:7 Luke 10:9 John 5:39
Really tnx ,,,I have land cruiser 2005 8v 4.7,,,errors p0985 p0986,,but which solenoid I should change ,,,while there are 8 sensors there 😂 ????
And how to change oil where there is no oil Gage ??😂😂😂
Where is the TCC solenoid 2000 Toyota Camry 2.2L.... 4.0 41e transmission
النمره الاخيره ماتعمل
1997 TOYOTA ALAVON TRANSMISSION WILL GO INTO REVERSE AND PULL CAR BACKWARDS, BUT WONT GO INTO DRIVE AND PULL CAR FORWARD,I CAN FILL TRANSMISSION GO INTO DRIVE BUT WONT PULL CAR FORWARD
Hi, please try oil fix. Replace new oil type Ford F type.
no
thanks
+Oscar Lopez Thank You. I appreciate Your feedback.
Rivers problem
👍
Hey Toyota, transmission Tacoma
Ok and many Thanks. :-)
Like. A. A. 340. Transmission.
Noted 👍
CAR DOCTOR
Happy new year! 😀
I learned nothing from this video
Ok. Watch again?
Which one is the Overdrive ?
Thanks for comment 😀👍