How I Make PERFECT Cutting Boards
HTML-код
- Опубликовано: 20 сен 2024
- Watch along as I show how to make a cutting board that will stand out from the rest!
Claphams Salad Bowl Finish - amzn.to/4aqD3NP
Tools I Use:
(Amazon Affiliate Links)
Incra Miter Express Value Pack - amzn.to/3UTDLNx
Wixey Digital Redout for Dewalt Planer - amzn.to/4dNr3IZ
Dewalt DW735X Planer - amzn.to/4dTLRPd
Dewalt Planer Stand - amzn.to/3yv8A3Q
Titebond 3 - amzn.to/3T0JDoI
THE BEST SANDPAPER!
80 Grit - amzn.to/49i9a2b
120 Grit - amzn.to/49CMt8C
180 Grit - amzn.to/49dUQIb
Featherboard - amzn.to/3I4skwD
Router - amzn.to/3SEFGEF
Mitre Saw - amzn.to/4bBQ2Op
Router Lift - amzn.to/3UNDJqJ
Audio/Video Gear:
DJI Mic - amzn.to/3IKa3oP
GoPro Hero 12 Black - amzn.to/4cm1LRr
Apurture Light - amzn.to/4crxAZm
Check me out at www.ryandaywoodworking.com
Cut your boards to the length you need. Hot glue a piece of 2x4 cut to be +4inches longer on each end to both sides. 2x4 pieces get the snip, boards are fine. I usually rip my 2x4 into thirds or half’s depending on the thickness of the wood to be protected.
Hope this helps.
Thanks for the tip!
Like your presentation style and like the end result.
Greetings from the other side of the pond. 🏴
Thanks! I really appreciate it!
I do not do juice grooves in my boards..
I have one board with juice groove, balance are no grooves. Agree with your point on why no grooves
I think if you are carving up a ton of juicy meat they have a place!
I have a juice groove and I like it. Cutting chicken or oranges and it doesn't run onto the counter.
Bravo you have mastered the cutting board.
I was just saying yesterday I really wish there was another cutting board video on RUclips.
Thanks for stopping by!
It is a tragedy that your free will has been eroded to the point that you are no longer able to just scroll on by.
@dian3145 Relax Karen.
We used to poke fun and rib all and everyone in the crafts.
Don't be a pussy with this he hurt my feelings.
Give the newbie a chance to cut back.
I can take it.
The juice groove on my board almost never sees any juice...but it doesw trap my darn garlic so you may be right :D
Haha!
2:59 Wouldn't it be better to place the concave edge against the level, as the two ends would make contact, rather than the convex edge which has a greater potential to shift during the cut? I use a tracksaw as I don't have a tablesaw, however what you are doing looks wrong to me...
It’s possible I have my concave and convex backwards. You don’t want the side where the edges curve away from the straightedge towards the fence. This would cause it to rock as you describe. You want to make sure you can maintain constant contact with the straight edge during the cut.
juice grooves are annoying but not if your cutting meat. I groove one side and say one side for meat one side for veggies
Yeah, I don’t carve a lot of meat, so not super useful for me. I do get that application though!
What happened to the compact table saw?
I was lucky enough to negotiate an upgrade with my wife! 😃