If possible then send me (with references)..But, l ll do. When I ll get free time. Therefore, go to about section of this channel there is mail..open it as desktop mode.
I am following exactly the steps of your video, but when I add drop lines, every spectra get superimposed at each other. Can you please help me out with this?
Hello, thank you for your informative video. Could you please provide some suggestions on how to draw multiple y-axes in a multiple stack graph? If it's easier, could you explain how to add multiple y-axes to the figure in your video? Thank you in advance. I'm eagerly awaiting your response.
@@NanoencryptionSKP I followed the procedure outlined below: I have 2 x-axes (x1 and x2) and a total of 4 y-axes (y1, y2, y3, y4). Here is the combination: (x1, y1), (x1, y2, y3) - It should be in layer-1 (x2, y2) - It should be in layer-2 I want multiple y-axes in layer-1; for example: (x1, y1) has one y-axis, and (x1, y2, y3) has a secondary y-axis. So, I attempted the following steps: Select all columns from the worksheet. Go to Plot > Multi-Curve > Stack. However, following this method, I couldn't separate the secondary y-axis in layer-1. Could you please provide me with detailed directions? I would be grateful for your guidance.
@@NanoencryptionSKP I followed the procedure outlined below: I have 2 x-axes (x1 and x2) and a total of 4 y-axes (y1, y2, y3, y4). Here is the combination: (x1, y1), (x1, y2, y3) - It should be in layer-1 (x2, y2) - It should be in layer-2 I want multiple y-axes in layer-1; for example: (x1, y1) has one y-axis, and (x1, y2, y3) has a secondary y-axis. So, I attempted the following steps: Select all columns from the worksheet. Go to Plot > Multi-Curve > Stack. However, following this method, I couldn't separate the secondary y-axis in layer-1. Could you please provide me with detailed directions? I would be grateful for your guidance.
@@NanoencryptionSKP I followed the procedure outlined below: I have 2 x-axes (x1 and x2) and a total of 4 y-axes (y1, y2, y3, y4). Here is the combination: (x1, y1), (x1, y2, y3) - It should be in layer-1 (x2, y2) - It should be in layer 2 I want multiple y-axes in layer-1; for example: (x1, y1) has one y-axis, and (x1, y2, y3) has a secondary y-axis. So, I attempted the following steps: Select all columns from the worksheet. Go to Plot > Multi-Curve > Stack. However, following this method, I couldn't separate the secondary y-axis in layer 1. Could you please provide me with detailed directions? I would be grateful for your guidance.
From XRD after you analysis your sample. Search on the software. assume if your material is ZnO nano. find ZnO then click on it. Then it will give information like structure (wurtzite, hexagonal), PDF card/ JCPDS card number etc Thanks
Sir I am also facing the same problem... I am using origin 2021, is it the reason that origin 2021 required another way to offset y values??? Please suggest me that sir
@@NanoencryptionSKP different materials in given nanoxide example in Fe3O4/ZnO/SiO2 composite we have iron oxide phase, zinc oxide phase and silicon oxide phase. I seen many journal draw three fitting you draw one at bottom
@@hope2633cu Please watch tutorial carefully.. Because, here I have just shown the process and only draw for single material that's nickel ferrite nanoparticles at different temperatures. If you have different materials then follow the same process by adding columns for others materials. Thank you 🙏
@@NanoencryptionSKP Sir how I can calculate JCPDS card for Ag & Cu nanoparticles because neither I nor my university have this software can you please help in this regard?
Thank you sir....it is very helpful for beginners.....Do upload videos like this....
how did you drag the graph and also changed the height of vertical lines just by clicking?? can you please tell me ??
Very well explained. I have a question, whether can we get free JCPDS cards. any link if available some websites for free JCPDS card.
Sir thanks for uploading the vdo. pls try to upload the fitting of ferroelectric hysteresis ( P-E ) loop. Pls keep this as my sincere request.
For dielectric constant fitting, follow the link
ruclips.net/video/j1DJlxa8LMU/видео.html
I don't have data on it.
@@NanoencryptionSKP sir I can provide the data. Pls send ur mail and try to fit. The theoretical equation also I have.
If possible then send me (with references)..But, l ll do. When I ll get free time.
Therefore, go to about section of this channel there is mail..open it as desktop mode.
@@harry-ho9ti hi Harry,can you please help me for the measurements P-E loop
This facility is not available with us. I did in some other lab. Sorry.
I am following exactly the steps of your video, but when I add drop lines, every spectra get superimposed at each other. Can you please help me out with this?
Mail me..
same
@@NanoencryptionSKP
@@NanoencryptionSKP me too, can you help me please?
thank you
Thanks
Hello, thank you for your informative video. Could you please provide some suggestions on how to draw multiple y-axes in a multiple stack graph? If it's easier, could you explain how to add multiple y-axes to the figure in your video? Thank you in advance. I'm eagerly awaiting your response.
Please follow this tutorial for double y-axis
@@NanoencryptionSKP I followed the procedure outlined below:
I have 2 x-axes (x1 and x2) and a total of 4 y-axes (y1, y2, y3, y4).
Here is the combination:
(x1, y1), (x1, y2, y3) - It should be in layer-1
(x2, y2) - It should be in layer-2
I want multiple y-axes in layer-1; for example: (x1, y1) has one y-axis, and (x1, y2, y3) has a secondary y-axis.
So, I attempted the following steps:
Select all columns from the worksheet.
Go to Plot > Multi-Curve > Stack.
However, following this method, I couldn't separate the secondary y-axis in layer-1.
Could you please provide me with detailed directions? I would be grateful for your guidance.
@@NanoencryptionSKP I followed the procedure outlined below:
I have 2 x-axes (x1 and x2) and a total of 4 y-axes (y1, y2, y3, y4).
Here is the combination:
(x1, y1), (x1, y2, y3) - It should be in layer-1
(x2, y2) - It should be in layer-2
I want multiple y-axes in layer-1; for example: (x1, y1) has one y-axis, and (x1, y2, y3) has a secondary y-axis.
So, I attempted the following steps:
Select all columns from the worksheet.
Go to Plot > Multi-Curve > Stack.
However, following this method, I couldn't separate the secondary y-axis in layer-1.
Could you please provide me with detailed directions? I would be grateful for your guidance.
@@NanoencryptionSKP
I followed the procedure outlined below:
I have 2 x-axes (x1 and x2) and a total of 4 y-axes (y1, y2, y3, y4).
Here is the combination:
(x1, y1), (x1, y2, y3) - It should be in layer-1
(x2, y2) - It should be in layer 2
I want multiple y-axes in layer-1; for example: (x1, y1) has one y-axis, and (x1, y2, y3) has a secondary y-axis.
So, I attempted the following steps:
Select all columns from the worksheet.
Go to Plot > Multi-Curve > Stack.
However, following this method, I couldn't separate the secondary y-axis in layer 1.
Could you please provide me with detailed directions? I would be grateful for your guidance.
Dears
Thanks for sharing this video, I want to know how can I find PDF card for the data of XRD? please
From XRD after you analysis your sample. Search on the software. assume if your material is ZnO nano. find ZnO then click on it. Then it will give information like structure (wurtzite, hexagonal), PDF card/ JCPDS card number etc
Thanks
May I get CsPbI3 JCPDC card for cubic and orthorhombic phases
Helo, Can you please share a video how to plot 3-D graphs of Reflection loss
Sir, I do not have data on it, if you have then please mail me. I'll try
I am following your instructions but I can't do the movement of the up and down graph, so please clearly explain this Sir/ Madam..
Send this
very interesting..... which command you are using for up and down of Xrd pattern?
Sir, please watch complete tutorial... after that you ll understand.
Sir I am also facing the same problem... I am using origin 2021, is it the reason that origin 2021 required another way to offset y values??? Please suggest me that sir
@@ayanroy9185 Sir, please follow this link
facebook.com/NanoESKP/videos/1300236450592826
I need your help plz, I tried to get match by xpert and Qualx but no results
Mail me..
I didn't find urs plz can you write it 😔 😪
@@artooof go to the about section of this channel and open as a desktop mode..
In my case all the standard peaks are of same size? Why is that happening? Can you pls give me any suggestions for correction?
Because may be your standard peaks are in normalized form but your data is not in narmalised form
Sir kindly send the jcpds software link to download it.
There is no downloaded link and also, it is run in 32bits only.
@@NanoencryptionSKP sir I need the software. I have 32 bit
Thanks for uploading this video, it was very useful. Question, Can you please provide me with jcpd card for Fe2O3 ?
Mail me
@@NanoencryptionSKP I have sent you an email. Thank you.
@@PFakame check your mail
@@NanoencryptionSKP Received, thank you very much.
I also need this jcpds please provide
good but if two more sample with different JCPDS??
You mean composite..?
@@NanoencryptionSKP different materials in given nanoxide example in Fe3O4/ZnO/SiO2 composite we have iron oxide phase, zinc oxide phase and silicon oxide phase. I seen many journal draw three fitting you draw one at bottom
@@hope2633cu Please watch tutorial carefully.. Because, here I have just shown the process and only draw for single material that's nickel ferrite nanoparticles at different temperatures. If you have different materials then follow the same process by adding columns for others materials.
Thank you 🙏
@@NanoencryptionSKPok i willl fight
Hello please, I want JCPDS for CuO; NiO and ZnO thank u for ur help
sir, Can you tell from where we will get JCPDS card?
Ask the operator of XRD, Before giving samples also ask to please give JCPDS card along with XRD raw data
@@NanoencryptionSKP
They Adviced to use Xpert high score software
@@NanoencryptionSKP Why we are not take out this directly from the Jade sir?
Sir can we know about shape of Ag and Cu nanoparticles through jcpd card? reply must plz
Yes
@@NanoencryptionSKP Sir how I can calculate JCPDS card for Ag & Cu nanoparticles because neither I nor my university have this software can you please help in this regard?
@@mahirajpoot6038 It's time taking.. Email me and give me some time⌚
sir, i have emailed you for hydroxyapatite card, please kindly reply sir, thank you
Sir can you plz send me bismuth oxide jcpd card.
Email me Chemical formula and Space group of this material..
How-to calculate H column? Thank u
Please watch tutorial completely upto H- column.. Because, in H-column i have simply used the jcpdf card number value
@@NanoencryptionSKP thank u