Nice explanation. I'm going to use mine to connect a solid state relay to switch a mains charger on and off so it doesn't have to be on all the time. Its for a backup to a solar system. The relay connections you explained allowed me to see this was possible.
Thanks for your review. I snagged one of these from a reseller for 50 cents, and frankly I'm still trying to figure out what I'll use it for. I suppose I could simply attach a basic wall-wart DC power source to the input and turn it into another Lead Acid charger, but somehow I think I have better I could do with it.
Robojax , love your veo tutorials, they are very scientific, laboratory grade measures, very professional and productive, thanks for your excelent work y friend !!
I have the same to charge a pack of 3 18650 batteries in series with 11,9 total volts and when it reaches de low voltage limit that i configured the relay start to turn on and off constantly and the voltimeter indicates peaks of 20 volts (voltage input from solar pannel) in the output to the battery. When apparently it stabilizes and the led is turned on it dont charging anything, the voltage drop on battery continues. The entrance line from solar pannel down from 20v to 11,42v when it s happens. Same result connecting dedicated 15 - 20v computer charger. ¿Low amps, my fault or module fault?
Hello, listen to the amps how are they managed? I need to charge a 12v 12A lithium battery pack. If I put a 1A charger on the battery does it get 1A? Thank you
Thanks for a very comprehensive description of this unit. I measured that the unit is taking about 70mA from the battery when its not turning charge on. I would like to reduce this by turning off the display when everything has been set up. Do you know of any way either in software or hardware to do this ?
Sorry about my english I from Argentina, I have the same problem and I can`t solve this at the moment. My battery is 1.2 amp and this module discharges it quicly because the unit is taking 70mA
Only way I could see to do that would be to break the track connection that feeds the positive supply to the led display and solder jumper wires and add a switch to be able to switch it on or off but too be honest these little led displays use very little power the difference is going to be minimal.
Hi, evey device that works or being triggered by votlage, has a limit. there is certain voltage to be considered as HIGH and LOW. I mentioned it for this device . for example in Arduino only 2V or higher is considered as HIGH and anything below it is LOW. for this module. I don't remember. just watch and see what I said.
Im looking to buy this Brand CPTDCL charger cut off board. Can you help me out. I have a portable solar set up and direct from alternator charging my secondary battery. Can I reverse the wires to the CPTDCL charger that go from the charger input, to the charging output to battery wires so instead of charging the battery, I want to rig it to operate a 12v motor and be able to start n shut it off.?
Charger voltage is normally 14.4V, to reach 100% capacity. And 13.2V is the voltage of full battery, but in disconnected state. So the cutoff voltage should be something close to 14.4V and not just 13.2V. Please make tests and comment on that, so ppl can get their batteries charged properly.
how does is control chargig current? for example on motorcycle 6ah battery its needed to charge at max 1amps and on bigger car batteries at least 5amps so does it control current and recognize battery capacity?
Do they make reverse relays it would be nice to make it do the opposite to protect the batteries and shut off an inverter when the battery gets too low. Thanks
Why is it that the charge time is right and wrong? If you have a lead acid battery the capacity is marked to 7v with a full charge cutoff being 14.6. But we tend to use the full capacity to make the calculation, but we don't use it all so it should be quicker. But..... When you charge, the current absorbed drops so you maybe charging at 2 amps by the end ...
Hi your videos are great. Thanks for all this. My project I am using 3.2v 18ah battery. I need a similar circuit with lower cutoff at 2.0v and max at 3.6v. Can you recommend a module for this voltage range.
During the time of demonstration of charging a 12 volt lead acid battery as per the video, I wanted to know how the battery voltage is increased or decreased manually as per your video. The battery voltage by default remains constant. It can be decreased during discharging process while connecting a load. Also the battery voltage can be increased during charging but will take some time that depends on the charging current. But my main query is how the battery voltage can be increased or decreased manually as shown in your video during the time of demonstration of charging a 12 volt battery????
No. as you charge the battery, the Constant Current source you have will initially to keep the current constant, suppresses the voltage in order to keep the current constant. as the current decreases when the battery is charged, the voltage is increases. this is normal behaviour of a constant current source.
Hi. Tks for sharing this valuable info, about this product. What I wanted to know is if it would be possible to use battery power during the recharging period ((imagining that this could increase the reload time, of course)...
First of all thank you for such a nice video. Is it possible to use a common socket for both charging and use? Just like a wireless hand drill. How to make a circuit.
Thank you very much for the good explanation . Please can you tell me whether I can use this to charge 100 amp battery. I use 100 amp battery for my home inverter. Thank you for your advice.
you are welcome. Yes you can charge. but maximum current as explained in the video, is 10A, more than that will kill this module. Check this better module that also measure the current up to 20A and it has tones of protections ruclips.net/video/2DaC6oOV9oA/видео.html
hi like the video I just wanted to know can you connect a load to the battery while it is in circuit and use it as a backup for a LED string light so when the AC power dies it will still run off the 12 Volt battery can one do this let me know if it's safe to do so. thank you.
The spec sheet on Amazon said the Input to HW-632 needed to be 10-30V DC, so I used a Laptop Charger, 19.33V DC Output, for the Input to HW-632. My HW-632 did not turn on. Your diagram indicates a 220V Charger Input. Please describe your 'Charger Output' voltage. HW-632 website description says the Input needs to be 10V-30V DC.
Hello, it seems you have not watched the video and skipped. I just watched the video and at 1:22 I said very important fact. At 1:43 I mentioned the connection, shown the diagram and explained what it does. the 10V-30V DC will make it turn ON and work.
Later in your video, you indicated that your Charger Input was 12.8V. Is that correct? So in Canada it's 220V Wall Outlet to the charger that was putting out 12.8 Volts. Is that correct? My unit didn't work at all. Input to HW-632 was 19.33V from a Laptop Charger. When I connected to an 18AH Battery, I didn't get any reading on the meter whatsoever. Any thoughts?
to learn about current, please see this video at 6:22 ruclips.net/video/3C33DpcSwIw/видео.html I spend time, searched for the video, played it and got the time for you.
I've added link to resources page for this product in the description of the video. here is the link for you robojax.com/learn/arduino/?vid=robojax_XH-M603_charger
may be you did not watch it. I have provided subtitle in most languages. Activate the subtitle so you understand. you should have your own charger. this is just turning the connection OFF if the voltage comes to the batter is greater than the set value.
Salaam Ahmed. I am currently setting up a XH M603 with a 16vac transformer , which has a bridge rectifier connected to achieve my DC power. My output after capacitor of the bridge rectifier is 24V. Currently the M603 is in standby mode attached to a 12v 9ah sealed lead acid battery. When the battery dropped to 12,5V the relay engaged on the switch over to 12,4V but then it rapidly rose to 12,8V and deactivated within seconds. What could be the cause here since my switch-off is at 13.4V. Do you have any advice please.
you did not mention what kind of 12V. I mention lead acid in the video please watch. 7Ah does not matter if it is 1Ah or 1000Ah. to charge for example your 7Ah batter at 1A. it means 1A/h (7Ah÷1A = 7A) and it will take 7 hours to fully charge or at 7A charge current it will take 1 hour (7Ah÷7A = 1h). if you have 100Ah batter at 1A current will take 100 hours to charge (100Ah÷1A = 100h). but if you charge it at 5A then 100Ah/50A=2 hours.
Hi, nice to greet you, I liked your video, but I have a question, could you clarify it for me? I have a transformer that in vacuum I measure 17 volts RMS but after I rectify it and filter it goes up to 24 approximately and that is correct because the capacitor that I am using is charged to the peak volt, now when I connect two lamps of 12v / 130w each One, the voltage drops to approximately 13.6v, the current that I measured consumption of these two lamps is 15.7 amps, could you then use this voltage source to inject it to the xh-m603 / 12-24v module,? the battery I intend to charge is 12v / 70A lead acid .. thanks mr,
Hi, I read this and did not get it before, but today I had reply as your comment was waiting in my mail box under "I haven't responded". I did not get "could you then use this voltage source to inject it to the xh-m603 / 12-24v module,?"
I used this as my car charging module. The lower charge set to 3v as my battery become dropped 5v once. And set the maximum volt to cut off as 13.2v. but when I connected the drained battery, the led light won't turn on for charging state. And it won't start charge. I checked the power supply. It was 16V at that time. Could you please tell what is wrong with the settings here?
I set the module to turn on led in the module while connected to drained battery now. But the led doesn't turn off when reached its maximum volt which I given for turn off. Hope your response as sooner possible.
Hi Robojax...how do you get the XH-M603 to detect and charge a battery below 5v DC? i have a 12v 7Ah UPS battery connected to the XH-M603 but it cannot detect the battery and charge even if i set the lower limit below 5vdc. I have the upper limit set to 13.7vdc. Please help me.
Hi, I don’t remember the minimum voltage but you set the main and maxim and it should keep your battery charging. Pay attention to what I said at the beginning. Watch carefully otherwise your battery can get damaged
@@robojax thanks for the quick reply Ahmad...once i set the lower (11.7vdc) and the upper limit (12.7vdc) even if the battery voltage is below the lower limit it will right away charge the battery and will stop charging at 12.vdc? thanks again.
This is just a switch to protect your laptop if voltage goes higher than the value you set. So use your charge or lower source and this module protects your load which is your laptop.
Hi Friend, I am trickle charging my car battery through Dewalt 20V using LM2596 and it's working really good and have been using it for about an year from now. Now my question is I want to protect my Dewalt Battery from going too low on Voltage and I tried using XH-M609 and LM2596 together but it didn't work. Now what do you suggest me to buy which might help. I appreciate any help please.
Hi, if you have a power module that has constant current, then you just set the voltage at maximum allowed voltage and set the current at charge current. For low voltage protection this module can be very helpful or this (we commenting at) module that can monitor the current as well ruclips.net/video/2DaC6oOV9oA/видео.html
Hello Mr. Ahmed! Thank you for the explainer video, it's really cool. Please help me in my inquiry, I need to protect the 48 volt 60 amp battery, where is it sold, and if there is any website on the internet that we can buy through it. Thank you very much all respect to you
Hello, Battery protection is not very simple. I forgot the maximum voltage for this module, but 60A does not matter when charging. it matters only if you are using it or discharging and you may need to protect it if you may draw very high current like 20A or so. But the rest depends on charge current and most devices with a simple relay can connect and disconnect 10 to 25A. here is one for 48V s.click.aliexpress.com/e/_9gIwp3 but there are many depending on how much you want to spend.
Mr. Ahmad shamshiri, please make a video explaining 3s bms board and tp4056 module explaining the benefits and uses in li-ion battery. Greetings to you from Saudi Arabia. Thanks
TP4056 is for 1S see datasheet here dlnmh9ip6v2uc.cloudfront.net/datasheets/Prototyping/TP4056.pdf See my other videos on chargers ruclips.net/user/robojaxTVsearch?query=charger
Can you tell what rating for a charger I would need to power my XH-m603 module, I want to charge cordless drill batteries which I believe are 18650 batteries?
This is NOT charger. I have explained it and also pot that in that title . This is chafer controller . This is just a switch to turn on or off a charger
@@robojax Sorry I'm not experienced enough. You said "charger or solar panel". I don't know if a solar panel is similar to a power supply. I've seen in other videos using an ATX PC, so my question is : can I safely use the 12 volts of a standard ATX PC input power supply?
@@robojax Thanks very much. I’m sorry - I didn’t explain well - I’m hoping to use this to charge a 4s22p 18650 pack. Im planning to set my bench power supply to around 16.7v, and connect the out put of the power-supply to this module.
@@robojax I am thinking of using this for a tool battery adaptor the only thing i need it to do is shut off once the lithium battery gets from 18v to low 15v. Do you think this PCB will work? The only concern i have is that tools can use high amps and i dont know if this board would handle it.
Please watch . This is just turning on and off. You need your own charger. Use this ruclips.net/video/fUYt0dQnkZc/видео.html or ruclips.net/video/I_rRTJgONTw/видео.html
your question made me watch the video and I found the answer. I even showed a diagram. I spent so much time making this video. so please watch it without skipping. I answer any question that is not answered in the video.
Hi, I mentioned that this is just turning ON and OFF. it can't control the current. so if your solar panel 's current is below the maximum amount of current that your battery can handle, then connect it directly. but if your solar panel can supply very high current that might damage your battery, then you need to put a charger or constant current device so limit the current.
Read or open the battery to see what the voltage is. then get a converter that has constant current mode or CC so you can set current limit. I have so many of those see my videos ruclips.net/user/RobojaxTVvideos and I have explained how to charge a battery
Hi, no because car battery needs to be connected continuously. this will disconnect the battery. also car will need regularly 30 to 50A and when starts it used about 100A to 400A. this can not handle more than 10A.
@@robojax No, Sorry my bad the question wasn't clear, I put it differently now, I have a portable Bank charger and that's connected to the car battery in the car for float charging and the charging is in progress, the charging voltage is 12.6 and now we go inside the car and acidentally start the car and the car Alternator is gonna kick in and push in 14.5 volts and huge amounts of Amps to the portable bank charger ( external charger) so the charging bank is not gonna be damaged from14.5 volts and lots of Ampere from the alternator or my external charging bank is protected by diodes?
@@robojax This unit will not Limit the amount of amps. Using this When you're alternator raises the voltage You may find that your battery is charging too fast.
If its a 12v lead acid battery that anyone is using this on the lower setting should be minimum 12.2v as going less than 50% discharge on a lead acid battery reduces their life considerably.
no. lead acid battery can go very low and it will not get damaged. But keep the lower value to 10.5V to 11V. it depends on what is this battery suppling power to.
Useless unless it controls current as well! It also needs battery to be fully discharged before it can be recharged. A XL4015 module seems a much better choice as controls voltage and current.
yes. that's why I gave warning. But for those with specific current power supply, this might be useful. I don't like it. Tht's why I did not put the lithium in the title too.
so you will use this XH-M603 as a switch. Watch this video to learn how a relay works ruclips.net/video/N-xbxtGGoHw/видео.html and use XH-M603 to control a relay that is capable to turn ON/OFF 100A like this relay amzn.to/3wFAHtB
Now this is called TRUE Review 👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻💯💯💯💯💯💯 explained with outstanding knowledge 🙏🏻
Nice explanation. I'm going to use mine to connect a solid state relay to switch a mains charger on and off so it doesn't have to be on all the time. Its for a backup to a solar system. The relay connections you explained allowed me to see this was possible.
Thanks from the Philippines
you are welcome. I try to put Philipines subtitle but getting very low traffic with subtitle.
Thanks for your review.
I snagged one of these from a reseller for 50 cents, and frankly I'm still trying to figure out what I'll use it for. I suppose I could simply attach a basic wall-wart DC power source to the input and turn it into another Lead Acid charger, but somehow I think I have better I could do with it.
Thank you very much for this review Ahmad !
My pleasure!
Good teaching sir. Thank you.
Excellent explanation and demonstration..
Glad it was helpful!
Robojax , love your veo tutorials, they are very scientific, laboratory grade measures, very professional and productive, thanks for your excelent work y friend !!
Excellent explanation. Thank you very much.
Glad it was helpful!
Thank you really so much
thank you
Super information!
Glad it was helpful!
I have the same to charge a pack of 3 18650 batteries in series with 11,9 total volts and when it reaches de low voltage limit that i configured the relay start to turn on and off constantly and the voltimeter indicates peaks of 20 volts (voltage input from solar pannel) in the output to the battery. When apparently it stabilizes and the led is turned on it dont charging anything, the voltage drop on battery continues.
The entrance line from solar pannel down from 20v to 11,42v when it s happens. Same result connecting dedicated 15 - 20v computer charger.
¿Low amps, my fault or module fault?
Nice explanation sooooper
Learned! Thanks 🎉
Hello, listen to the amps how are they managed? I need to charge a 12v 12A lithium battery pack. If I put a 1A charger on the battery does it get 1A? Thank you
Love from kashmir ❤️
❤️
Thanks for a very comprehensive description of this unit. I measured that the unit is taking about 70mA from the battery when its not turning charge on. I would like to reduce this by turning off the display when everything has been set up. Do you know of any way either in software or hardware to do this ?
Sorry about my english I from Argentina, I have the same problem and I can`t solve this at the moment. My battery is 1.2 amp and this module discharges it quicly because the unit is taking 70mA
Only way I could see to do that would be to break the track connection that feeds the positive supply to the led display and solder jumper wires and add a switch to be able to switch it on or off but too be honest these little led displays use very little power the difference is going to be minimal.
Nice review video
Thank you! Cheers!
Muy bueno el vídeo... Desde México
Me complace que te guste. Saludos desde Canadá
Here is better module ruclips.net/video/2DaC6oOV9oA/видео.html
Hi ! At 8:10 can the "start/low" voltage be increased up to "stop/high" voltage -0.2V ?
Hi, evey device that works or being triggered by votlage, has a limit. there is certain voltage to be considered as HIGH and LOW. I mentioned it for this device . for example in Arduino only 2V or higher is considered as HIGH and anything below it is LOW. for this module. I don't remember. just watch and see what I said.
Im looking to buy this Brand CPTDCL charger cut off board. Can you help me out.
I have a portable solar set up and direct from alternator charging my secondary battery.
Can I reverse the wires to the CPTDCL charger that go from the charger input, to the charging output to battery wires so instead of charging the battery, I want to rig it to operate a 12v motor and be able to start n shut it off.?
thanks alot
Great job
can a 24v 5a power supply work on this module?
Thanks, very informative, Can I use this on my car/Motor cycle to charge 2nd battery?
Charger voltage is normally 14.4V, to reach 100% capacity. And 13.2V is the voltage of full battery, but in disconnected state. So the cutoff voltage should be something close to 14.4V and not just 13.2V. Please make tests and comment on that, so ppl can get their batteries charged properly.
how does is control chargig current? for example on motorcycle 6ah battery its needed to charge at max 1amps and on bigger car batteries at least 5amps so does it control current and recognize battery capacity?
Do they make reverse relays it would be nice to make it do the opposite to protect the batteries and shut off an inverter when the battery gets too low. Thanks
Nwvermind they make a xycd63l they has both load and charge fynction way cool
Very nice explantion 👌, excellent video
Glad you liked it
Why is it that the charge time is right and wrong?
If you have a lead acid battery the capacity is marked to 7v with a full charge cutoff being 14.6.
But we tend to use the full capacity to make the calculation, but we don't use it all so it should be quicker.
But.....
When you charge, the current absorbed drops so you maybe charging at 2 amps by the end ...
Hi your videos are great. Thanks for all this. My project I am using 3.2v 18ah battery. I need a similar circuit with lower cutoff at 2.0v and max at 3.6v. Can you recommend a module for this voltage range.
During the time of demonstration of charging a 12 volt lead acid battery as per the video, I wanted to know how the battery voltage is increased or decreased manually as per your video. The battery voltage by default remains constant. It can be decreased during discharging process while connecting a load. Also the battery voltage can be increased during charging but will take some time that depends on the charging current. But my main query is how the battery voltage can be increased or decreased manually as shown in your video during the time of demonstration of charging a 12 volt battery????
No. as you charge the battery, the Constant Current source you have will initially to keep the current constant, suppresses the voltage in order to keep the current constant. as the current decreases when the battery is charged, the voltage is increases. this is normal behaviour of a constant current source.
@@robojax Thank you for the clarification. Your videos are very informative and interesting as well.
yararlı bir anlatım olmuş Thank you
rica ederim.
Nice video...thank you
You are welcome. Here is $200 Arduino course for free Arduino Step by Step Course (over 100 lectures) Starts here robojax.com/L/?id=338
Hi. Tks for sharing this valuable info, about this product. What I wanted to know is if it would be possible to use battery power during the recharging period ((imagining that this could increase the reload time, of course)...
Hi, of course you can use the battery 🔋
Please make a video on Roboarm with arduino 🙏🙏
Never hard the word 'Roboarm".
@@robojax robo-arm using arduino
First of all thank you for such a nice video. Is it possible to use a common socket for both charging and use? Just like a wireless hand drill. How to make a circuit.
Power your tool from battery. Or power it from charger . It should work when the power supply is connected to this module.
Thank you very much for the good explanation . Please can you tell me whether I can use this to charge 100 amp battery. I use 100 amp battery for my home inverter. Thank you for your advice.
you are welcome. Yes you can charge. but maximum current as explained in the video, is 10A, more than that will kill this module. Check this better module that also measure the current up to 20A and it has tones of protections ruclips.net/video/2DaC6oOV9oA/видео.html
Sir I seen your videos very interested
So nice of you
hi like the video I just wanted to know can you connect a load to the battery while it is in circuit and use it as a backup for a LED string light so when the AC power dies it will still run off the 12 Volt battery can one do this let me know if it's safe to do so. thank you.
Yes you can
My battery is connected with a 10 amp load, will this module sustain such load if i use it to charge the battery?
you made me watch the video. I have explained how much current the relay can handle. please watch
how can I use this as a load dump using wind generator
can it work with dc input ?
Hi
I want to ask u
Can i put A 31 volt solar panel and I charge one 12 volt battery from it through this circuit? Or it should be 24 v battery.
Thanks
Hi, may be you did not watch the video. This is just a switch like On or off it does not change the voltage. See th video
@@robojax ok
Do u have any idea how we use 31v solar panels from 31 volt to charge batterie 12 volt. Only one battery?
Thanks
@@zaferibrahim use a step down converter to change 31v to 14v and ur good to go
The spec sheet on Amazon said the Input to HW-632 needed to be 10-30V DC, so I used a Laptop Charger, 19.33V DC Output, for the Input to HW-632. My HW-632 did not turn on. Your diagram indicates a 220V Charger Input. Please describe your 'Charger Output' voltage. HW-632 website description says the Input needs to be 10V-30V DC.
Hello, it seems you have not watched the video and skipped. I just watched the video and at 1:22 I said very important fact. At 1:43 I mentioned the connection, shown the diagram and explained what it does. the 10V-30V DC will make it turn ON and work.
Dear Ahmed ,Starts this Board Automatic? İcant See a on Off Button.
Later in your video, you indicated that your Charger Input was 12.8V. Is that correct? So in Canada it's 220V Wall Outlet to the charger that was putting out 12.8 Volts. Is that correct? My unit didn't work at all. Input to HW-632 was 19.33V from a Laptop Charger. When I connected to an 18AH Battery, I didn't get any reading on the meter whatsoever. Any thoughts?
to learn about current, please see this video at 6:22 ruclips.net/video/3C33DpcSwIw/видео.html I spend time, searched for the video, played it and got the time for you.
I've added link to resources page for this product in the description of the video. here is the link for you robojax.com/learn/arduino/?vid=robojax_XH-M603_charger
For imput AC is good to charge 12v 7Ah baterry whit 15v and 3Ah?
may be you did not watch it. I have provided subtitle in most languages. Activate the subtitle so you understand. you should have your own charger. this is just turning the connection OFF if the voltage comes to the batter is greater than the set value.
Salaam Ahmed. I am currently setting up a XH M603 with a 16vac transformer , which has a bridge rectifier connected to achieve my DC power. My output after capacitor of the bridge rectifier is 24V. Currently the M603 is in standby mode attached to a 12v 9ah sealed lead acid battery. When the battery dropped to 12,5V the relay engaged on the switch over to 12,4V but then it rapidly rose to 12,8V and deactivated within seconds. What could be the cause here since my switch-off is at 13.4V. Do you have any advice please.
Walaikum Salam It seems your battery is full and that could be the only reason
@@robojax shukran for the haste reply .
afwan.
اسلام علیکم
Float charging voltage for tubler battery 24 voltage system also bulk charging s voltage ?
Please
How many volts do you have on the input for a 12v 7Ah battery?
you did not mention what kind of 12V. I mention lead acid in the video please watch. 7Ah does not matter if it is 1Ah or 1000Ah. to charge for example your 7Ah batter at 1A. it means 1A/h (7Ah÷1A = 7A) and it will take 7 hours to fully charge or at 7A charge current it will take 1 hour (7Ah÷7A = 1h). if you have 100Ah batter at 1A current will take 100 hours to charge (100Ah÷1A = 100h). but if you charge it at 5A then 100Ah/50A=2 hours.
Hi, nice to greet you, I liked your video, but I have a question, could you clarify it for me? I have a transformer that in vacuum I measure 17 volts RMS but after I rectify it and filter it goes up to 24 approximately and that is correct because the capacitor that I am using is charged to the peak volt, now when I connect two lamps of 12v / 130w each One, the voltage drops to approximately 13.6v, the current that I measured consumption of these two lamps is 15.7 amps, could you then use this voltage source to inject it to the xh-m603 / 12-24v module,?
the battery I intend to charge is 12v / 70A lead acid ..
thanks mr,
Hi, I read this and did not get it before, but today I had reply as your comment was waiting in my mail box under "I haven't responded". I did not get "could you then use this voltage source to inject it to the xh-m603 / 12-24v module,?"
Hi is possible attach a load in parallel of battery ?? thanks
Hi, yes it is possible.
Can i ask if i can use this for 48v 20ah sla battery for ebike
I hope you have watched the video fully. If so then yes. If not, you will damage your batter if you don’t understand
I used this as my car charging module. The lower charge set to 3v as my battery become dropped 5v once. And set the maximum volt to cut off as 13.2v. but when I connected the drained battery, the led light won't turn on for charging state. And it won't start charge. I checked the power supply. It was 16V at that time. Could you please tell what is wrong with the settings here?
I set the module to turn on led in the module while connected to drained battery now. But the led doesn't turn off when reached its maximum volt which I given for turn off. Hope your response as sooner possible.
Hi Robojax...how do you get the XH-M603 to detect and charge a battery below 5v DC? i have a 12v 7Ah UPS battery connected to the XH-M603 but it cannot detect the battery and charge even if i set the lower limit below 5vdc. I have the upper limit set to 13.7vdc. Please help me.
Hi, I don’t remember the minimum voltage but you set the main and maxim and it should keep your battery charging. Pay attention to what I said at the beginning. Watch carefully otherwise your battery can get damaged
@@robojax thanks for the quick reply Ahmad...once i set the lower (11.7vdc) and the upper limit (12.7vdc) even if the battery voltage is below the lower limit it will right away charge the battery and will stop charging at 12.vdc? thanks again.
Good
Thanks
Can it be used with a 16 volt 4.5A laptop charger? As far as I understand, the chip puts out up to 3 Amps on XH-M603
This is just a switch to protect your laptop if voltage goes higher than the value you set. So use your charge or lower source and this module protects your load which is your laptop.
is it ok to use old laptop power supply 19volts 2amp? i will try diy battery charger for my spare motorcycle battery 12volts..
Hi, I get all these questions because people don't watch fully and ask questions. Please watch. I have specifically mention this portion.
Hi Friend, I am trickle charging my car battery through Dewalt 20V using LM2596 and it's working really good and have been using it for about an year from now. Now my question is I want to protect my Dewalt Battery from going too low on Voltage and I tried using XH-M609 and LM2596 together but it didn't work. Now what do you suggest me to buy which might help. I appreciate any help please.
Hi, if you have a power module that has constant current, then you just set the voltage at maximum allowed voltage and set the current at charge current. For low voltage protection this module can be very helpful or this (we commenting at) module that can monitor the current as well ruclips.net/video/2DaC6oOV9oA/видео.html
Could you wire this in with a dc to dc buck boost converter between this module and the solar panel or pwm?
If so also what max current shall I limit it too, knowing this module is rated for 10 amps max? I would say give a cushion of 8 amps max.
Can I use this to charge my AGM batteries in my caravan from main battery when I’m driving ?
this just know the voltage. it voltage is within range and the current does not exceed the raring of relay, it should work.
Hello Mr. Ahmed!
Thank you for the explainer video, it's really cool.
Please help me in my inquiry, I need to protect the 48 volt 60 amp battery, where is it sold, and if there is any website on the internet that we can buy through it.
Thank you very much
all respect to you
Hello,
Battery protection is not very simple. I forgot the maximum voltage for this module, but 60A does not matter when charging. it matters only if you are using it or discharging and you may need to protect it if you may draw very high current like 20A or so. But the rest depends on charge current and most devices with a simple relay can connect and disconnect 10 to 25A. here is one for 48V s.click.aliexpress.com/e/_9gIwp3 but there are many depending on how much you want to spend.
Can I set charging start voltage to 9v ,so to use for lithium battery
The relay is 12V. it will not work. needs 12V.
@@robojax but 12v relay even works with 9v battery
Can this be used in a piezoelectric power generation system to charge the battery?
I have you have watched the video and then posted the comments. I have not left anything out. please watch as if I type it, then why I made the video?
Which is much better charging module, XY-DJ or XH-M603?
Hoping for your response?
it is your choice. I can't suggest which one because each person is using it differently.
Are the top 4 open pins for serial communication? If so is there any documentation on this?
That’s for the manufacturer only. No info
Xhm603 board support 12v 5 a charger for 12v car battery
Mr. Ahmad shamshiri, please make a video explaining 3s bms board and tp4056 module explaining the benefits and uses in li-ion battery.
Greetings to you from Saudi Arabia. Thanks
TP4056 is for 1S see datasheet here dlnmh9ip6v2uc.cloudfront.net/datasheets/Prototyping/TP4056.pdf See my other videos on chargers ruclips.net/user/robojaxTVsearch?query=charger
Can you tell what rating for a charger I would need to power my XH-m603 module, I want to charge cordless drill batteries which I believe are 18650 batteries?
This is NOT charger. I have explained it and also pot that in that title . This is chafer controller . This is just a switch to turn on or off a charger
Yes I know but the charger that you connect to the controller, what rating should I go with , ?
Can I use it in a motorcycle to charge a secondary battery for other accessories ?
we don't look at name "car" or "plane". it is the voltage. so you can use it anywhere.
Excuse me, can you kindly explain me if the object in the left (charger input) is a power supply or a charger ?
Hi, it seems you have not watched the video. I answer any question that is not answered in the video. Please watch
@@robojax Sorry I'm not experienced enough. You said "charger or solar panel". I don't know if a solar panel is similar to a power supply. I've seen in other videos using an ATX PC, so my question is : can I safely use the 12 volts of a standard ATX PC input power supply?
Great video and really love your content. Is there any reason this module cant be used to control lithium batteries (18650s)?
because input voltage minimum is 10V so you can't change 1 cell. also accuracy is 100mA and for lithium batteries 100mV can't be big deal.
@@robojax Thanks very much. I’m sorry - I didn’t explain well - I’m hoping to use this to charge a 4s22p 18650 pack. Im planning to set my bench power supply to around 16.7v, and connect the out put of the power-supply to this module.
you can charge 18650. set it to 12.6(4.2v/cell)for max and 11.5 for min voltage but be sure to have 3S balancer.
@@robojax I am thinking of using this for a tool battery adaptor the only thing i need it to do is shut off once the lithium battery gets from 18v to low 15v. Do you think this PCB will work? The only concern i have is that tools can use high amps and i dont know if this board would handle it.
Hello. Can this module charger be used with lifepo4 and 18650 batteries?
Please watch . This is just turning on and off. You need your own charger. Use this ruclips.net/video/fUYt0dQnkZc/видео.html or ruclips.net/video/I_rRTJgONTw/видео.html
I have 24v charger can i use 12v car battery charge its work???with this? Controller???
You have not watched ether video fully, else you won’t have asked this question. Please watch
Question. If During charge the upper voltage isn't reached and the voltage ends up going below the cut in set point will it stop charging?
your question made me watch the video and I found the answer. I even showed a diagram. I spent so much time making this video. so please watch it without skipping. I answer any question that is not answered in the video.
@@robojax I am truly sorry. I don't want to be that guy.
Hi Ahmad, can solar panel connect directly to the charger controller to charge the battery ?
Hi, I mentioned that this is just turning ON and OFF. it can't control the current. so if your solar panel 's current is below the maximum amount of current that your battery can handle, then connect it directly. but if your solar panel can supply very high current that might damage your battery, then you need to put a charger or constant current device so limit the current.
We have an problem then. The module discharge the battery on time, once is powered by the battery!!
Hi Ahmad,
Can I use it for a "solar panel" as input to charge my battery?
Does "XY-L30A" have benefits against XH-M603?
no. you can't. I mentioned that you need a charger. This is NOT a charger. Please watch fully to get answer to all your questions.
@@robojax What module do you recommend for a charger?
Hey sir can i charge 24v battery with this device? 😢
Hi, I don't remember anything. I have mentioned the maximum voltage. Please watch
can it be connected with the charger 24×7 in ON position
I have not tested continuously for long period of time but that is what is expected from a product.
How can I connect a adapter to charger a drill battery which I don’t have a original charger for the battery
Read or open the battery to see what the voltage is. then get a converter that has constant current mode or CC so you can set current limit. I have so many of those see my videos ruclips.net/user/RobojaxTVvideos and I have explained how to charge a battery
@@robojax what video specifically do I look for these batteries are 18650 batteries
Can you reverse this and use it as low voltage protection?
No you can’t. This is for Lead Acid batteries which love voltage does not damaged them.
Hi there, can it be used as a on board car battery maintainer/ tender ??
Hi, no because car battery needs to be connected continuously. this will disconnect the battery. also car will need regularly 30 to 50A and when starts it used about 100A to 400A. this can not handle more than 10A.
@@robojax No, Sorry my bad the question wasn't clear, I put it differently now, I have a portable Bank charger and that's connected to the car battery in the car for float charging and the charging is in progress, the charging voltage is 12.6 and now we go inside the car and acidentally start the car and the car Alternator is gonna kick in and push in 14.5 volts and huge amounts of Amps to the portable bank charger ( external charger) so the charging bank is not gonna be damaged from14.5 volts and lots of Ampere from the alternator or my external charging bank is protected by diodes?
????
@@robojax This unit will not Limit the amount of amps. Using this When you're alternator raises the voltage You may find that your battery is charging too fast.
If its a 12v lead acid battery that anyone is using this on the lower setting should be minimum 12.2v as going less than 50% discharge on a lead acid battery reduces their life considerably.
no. lead acid battery can go very low and it will not get damaged. But keep the lower value to 10.5V to 11V. it depends on what is this battery suppling power to.
Can I use it to charge a 18v battery ?
your question is answered in the video.
@robojax Thank you for you response ? So the answer is Yes or No ?
Only batteries of 12v and 24v are compatible or the range between of 12-24 V batteries are compatible ? @robojax
Useless unless it controls current as well! It also needs battery to be fully discharged before it can be recharged.
A XL4015 module seems a much better choice as controls voltage and current.
yes. that's why I gave warning. But for those with specific current power supply, this might be useful. I don't like it. Tht's why I did not put the lithium in the title too.
They have a New versión with 90v
Tried mine but not working
Can this module use in 4s 12v lifepo4 battery?
your question suggests that you have not watched the video. Please watch to get your answer.
@@robojax what i mean if i can still connect this module direct from the solar panel to lifepo4 battery safe?
Yes. you can. this module can work with that but does not control the current.
Pls sir how can i get the one to work on 100amps charger
Make this loupe to turn ON and OFF a huge relay that controls the connection of 100A
@@robojax pls sir how can i make that connection provided that my charger is 24volts generating a 100Amps
so you will use this XH-M603 as a switch. Watch this video to learn how a relay works ruclips.net/video/N-xbxtGGoHw/видео.html and use XH-M603 to control a relay that is capable to turn ON/OFF 100A like this relay amzn.to/3wFAHtB
Sir please make a video on an XH-M603 using a relay on it please
Can I use it to charge lithium battery?
Please watch it. This is NOT a charger
Sir ic number and programing
I will not even think about that the charging controller has mini connections for heavy cabling, .garbage.
This is made for 10A only.
Saya suka ada ada arti bahasanya...
Saya senang Anda menyukainya. Ahmad dari Kanada.
@@robojax
Iya saya suka dn menambah pengetahuan biar saya tahu.
12.6 volt lithium battery kaise charge Karu
English or Farsi please.
👍
😊
2type micro controller . Micro controller number 2type
Let me add one like so you get 1K likes😊