Building a Rail Car for Abandoned Railroads

Поделиться
HTML-код
  • Опубликовано: 19 май 2024
  • Use code SPIRA50 to get 50% OFF your first Factor box plus 20% off your next month at bit.ly/4bksEED!
  • РазвлеченияРазвлечения

Комментарии • 1,3 тыс.

  • @markthesun2140
    @markthesun2140 23 дня назад +393

    It's your wheels!!! Rubber grips too much and walks off. Metal wheels allows to slip

    • @Siph_Maned_Wolf
      @Siph_Maned_Wolf 22 дня назад +50

      Don’t forget that the wheels need to be on a fixed shared axel where they both rotate as a connected pair which is what really takes advantage of the sloped wheel shape

    • @squishycrab6330
      @squishycrab6330 21 день назад +19

      I was under the impression that train wheels weren’t rubber because the train would either destroy the rubber instantly, or wear extremely fast. It makes sense that they would have to have some slip.

    • @Siph_Maned_Wolf
      @Siph_Maned_Wolf 21 день назад +8

      @@squishycrab6330 that is also very true. While there are many different materials they could use, it doesn’t change the fact that those materials will need a way to be replaced often and easily. They were experimented with on some trolleys and single unit rail vehicles but for trains they really are not worth it.

    • @davidbarnett3732
      @davidbarnett3732 20 дней назад +1

      At the very least I would make a thick aluminum backplate for your wheels, the rubber may wear down and then you're screwed again. Making metal wheels would probably be better, but this is not my area of expertise.
      By the way, this was great fun, and your experience was infectious

    • @whatyoumakeofit6635
      @whatyoumakeofit6635 19 дней назад +4

      A metal band around the wheels would work. If possible to do that. Alot of nvh would be isolated through the wheels, making a nice ride.

  • @kenmcneeley8045
    @kenmcneeley8045 19 дней назад +30

    I'm 80 years old and have wanted to take an adventure like this forever. I had to smile during the entire journey.

    • @bazra19
      @bazra19 15 дней назад +1

      Hi Youngster, I'm 84 it made me smile as well. Do you think us two old farts could give them a run for thier money?

  • @mrheart4242
    @mrheart4242 21 день назад +37

    Build a trailer. Put it on the back so you will have sleeping quarters and a place to mount solar panels to recharge it.

  • @avfc1985
    @avfc1985 20 дней назад +31

    Buy train wheels

  • @jcraigie
    @jcraigie 20 дней назад +13

    "The batteries fully charged! We could potentially go a hundred miles."
    "We've got one hour of daylight left."
    LMAO
    I love the enthusiasm. Cool contraption.

  • @nordstar2698
    @nordstar2698 24 дня назад +80

    Matt has definitely beaten life already and is just doing the side quests now

    • @greenlightchronicles7198
      @greenlightchronicles7198 21 день назад +1

      S shows the difference between a new beginning channel and one coming from a rich family..
      Most individuals takes years to learn how to GTAW .. he learn it in 1 night he says 😂😂😂
      More then rich ..

  • @scottindestin4292
    @scottindestin4292 19 дней назад +10

    All the puppies worked really well together on that puppy.

  • @superbmediacontentcreator
    @superbmediacontentcreator 21 день назад +8

    This was a fantastic idea
    Here are some engineering suggestions You needed to attach a drill with eccentric weight to vibrate the wheel mold as you poured. Other than a Lexan disk with a kitchen vacuum bag attachment these are the most accessible ways to get the bubbles out of your polyurethane pour.
    Bolt thick oversized disks on the back of your wheels to keep the wheels on the track.
    You need a power conversion system and chain drive to your train wheels with a jack system to put down and pull up the original wheels & tires, but they are great for just moving the car around. You struggle too much and need a pair of stakes at the back and go in the ground so you can pitch it over more easily.
    A fold-up cow catcher to knock things off the track as you go would help.
    Oh, and you need a puppy...

  • @Goigigandfriends
    @Goigigandfriends 23 дня назад +13

    It’s so funny I know so many people who just won’t do anything. They’ve never tried before and here you are in one video doing like 90 things for the first time ever and excelling at them. People really need to open and broaden their horizons.

  • @rayvestrayvene5376
    @rayvestrayvene5376 20 дней назад +6

    When I was young I had a 1967 Plymouth and when I let some air out of the tires they would conform to the shape of the top of the rails. The width of the car was exactly the width of the rails. It was so fun we'd all get on top of the car. I only had to touch the steering wheel over road crossings.

  • @worldtraveler930
    @worldtraveler930 20 дней назад +6

    When I was a little kid my parents took a 1939 Ford Deluxe to the railroad tracks behind our house the Ford matched exactly so all you had to do is slightly let some air out of the tires and drive all the way into town and back having an sparkplug airpump to pump the tires backup it made a fun ride!!! 🤠👍

  • @duck9487
    @duck9487 24 дня назад +9

    You’re my favourite motorcycle/ fun vehicle stuff channel, you’re doing great stuff on this channel

  • @Kubametrostroi
    @Kubametrostroi 3 дня назад +11

    2:34 galvanized square steel

  • @lugertelevisioncompany
    @lugertelevisioncompany 20 дней назад +8

    The biggest thing people forget is that the wheels on a train aren’t actually connected to the train. The train sits on them and the weight of the cars keeps them in place along with the flange on the wheel.

  • @brooknet
    @brooknet 21 день назад +5

    Absolutely sensational! I'm in Britain and in the late 60s, a lot of our railway infrastructure was closed and dismantled. Why not make them all available to the public so they can build their own vehicles? (well, saying that, it occurred to me that once health & safety get involved, that won't leave much freedom for hobbyists to experiment.. rules! Why?)

  • @Consequator
    @Consequator 20 дней назад +5

    The cone shape of train wheels is mandatory. The lip will just grind away really quick in corners. The smooth non grip cone shape is what keeps the train from staying on the tracks instead of going straight when it should be making a turn.
    As seen around 26:00 the cast rubber has enough grip to lift the vehicle up and over the track from friction against the ridge which is why it was derailing. That is also what your buddy is experiencing at 34:00
    But like you said, you really need all metal wheels. You might be able to put like a rubber ring around them for a smoother ride but they are going to wear away really quick.
    If its all metal you might also be able to set off railway crossings that are still active :)

  • @mankihonda983
    @mankihonda983 20 дней назад +5

    The gaps would probably be lot smoother with bigger wheels.

  • @Blaquer17
    @Blaquer17 20 дней назад +6

    Your buddy missed an opportunity to say the steering is vague, but it still handles like its on rails!

  • @bigskunk801
    @bigskunk801 7 дней назад +4

    The reason train wheels are tapered is because they have a solid axle and the taper changes the speed of each wheel when going around corners.

  • @limyrob1383
    @limyrob1383 22 дня назад +5

    Some suggestions - you can buy small steel rail wheels for factory trucks, they are the correct profile. You need some simple suspension with only 1-2" travel and where people make stuff like this they put all the weight on one side (like a motorcycle and sidecar) and put the rubber driving wheel on that side. It needs to be easy to reverse, go both ways or turn round or you have a long way back!

  • @SeanHarlow
    @SeanHarlow 22 дня назад +3

    One of my favorite genres of video is people building rail carts, and I'm constantly amazed how common it is for people, even those sufficiently mechanically savvy and interested by rail to even attempt such a thing, to not really understand just how important the exact shape of rail wheels is to their performance and operation. Everyone seems to have to learn that one the hard way.

  • @JD-kg3mx
    @JD-kg3mx 3 дня назад +8

    Engineering 101: Learn Murphy's Law. You have to have a backing plate on each of the wheels. Just watching others that've made rail carts would've shone you that.

  • @Marshimized
    @Marshimized 20 дней назад +5

    getting some good engagement on this one! you don't need me to tell you, but be thankful for the idiots that are just here to hate, and take the ACTUAL criticism into mind. all these comments helped get this vid into my recommended, this was a fun watch! looks fun as hell, keep doing cool shit!!

  • @JeremiahLauzon
    @JeremiahLauzon 19 дней назад +7

    You know why train wheels are angled? It’s so they can self correct. Having a flange would also greatly benefit you.

    • @ownie6487
      @ownie6487 19 дней назад +1

      I thought it was so they could turn too

    • @mlindholm
      @mlindholm 19 дней назад +1

      @@ownie6487 it is to allow them to go around curves, since the inner wheel will ride down on the cone, the outer will ride up therefore allowing them to roll different amounts (circumference) while both rigidly attached to the same axle (same 360 rotation).

    • @JeremiahLauzon
      @JeremiahLauzon 15 дней назад

      @ownie6487 Yes. I should have specified it's to "self correct on turns" due to how the wheels work. The comment above mine explained very well.

  • @user-xw7up4hq9j
    @user-xw7up4hq9j 3 дня назад +15

    not making fun of him but most used word in this video is “puppy”

  • @kaydesign
    @kaydesign 21 день назад +5

    Easier solution; attach a wooden disk next to the big motorized wheels. Then the tyres become train wheels. Works great and is way more simple.

  • @johnhaberny1812
    @johnhaberny1812 19 дней назад +7

    Anybody else realize how much he says puppies??😂

  • @Capturing-Memories
    @Capturing-Memories 20 дней назад +6

    Next add front debris removal blade, don't forget train air horn.

  • @electrico325
    @electrico325 2 дня назад +12

    i wonder how many times he said "puppy"?

  • @trstmeimadctr
    @trstmeimadctr 22 дня назад +6

    When you're mixing things like eurethane, you should double mix it, meaning mix it in the container but then pour it into something else and mix again. The number one cause of a bad cast is unmixed residue clinging to the walls of the container

  • @adamguymon7096
    @adamguymon7096 4 дня назад +5

    What I would do is get another one of those vehicles and put it back to back and get some better wheels for the job. Then you would have the ability to drive the vehicle in one direction and then just get into the other end to go the other direction. Get some good lights and in between both vehicles you would have a box to put your gear in so you could go on a few-day journey and you could have all of your food and other things to be comfortable. This looks cool and fun. We need to see a video where you go on a longer trip.

  • @johnhaberny1812
    @johnhaberny1812 19 дней назад +6

    “These puppies”😂

  • @oilio5465
    @oilio5465 24 дня назад +4

    You should add a cow catcher to the front.
    Would look cool. Plus it will protect the wheels from stuff on the track

  • @Quacks0
    @Quacks0 3 дня назад +4

    7:55 I love what he says regarding his feeling smugly happy when re-using recycled/leftover bolts --- I always experience the same self-satisfied glow whenever I am able to use already-on-hand fasteners instead of buying costly new ones at the hardware store, in that it kind of vindicates my hoarder instincts. :D

  • @QUIX4U
    @QUIX4U 18 дней назад +6

    Fun fact, make a fullt welded "absolutely square" sub-chassis, that simply bolts onto the upper fibreglass superstructure.
    Forget about "having the ground down with angle grinder and belt grinder wheels and MAKE THEM AGAIN knowingthat yur friend has a lathe, do them ALL at the same time, with at least a 3/4 inch HEIGHT flange, slightly bevelled by about 3 - 5 degrees.
    The treads do NOT have to be as sloped as you had them before, allowing a deeper tread to top of flange distance, as (even though the theoru=y of a cambered wheel, keeps a train on the tracks) actual on-track rail conditions are that often there is a variance between true can and twists that allows the cant to vary enough, to throw you, if the only thing you are relying on, is the dual cambers of both wheels, which if not ABSOLUTELY PARRALEL with the back axle, the front won't stay on the track & visa versa with the rear wheels, especially in reverse.
    So, weld BOTH axle blocks to a subchassis of steel, bolt THAT to the fibreglass upper superstructure, and NEVER hava tracking problem, ever again.
    BUT YOU MUST HAVE PROPER FLANGES, as they are "not" there for good looks, they have a specific job, and THAT is to keep the rail wheels "at gauge", which they cannot do if the flange faces are uneven, out of round, or not identically parrallel between both axles, I mean both axles must be absolutely parrallel to each other.
    Rely on the weight of the drven rubber wheels, to ONLY drop down onto the rail to "drive", as they are NOT THERE NOW, for suspension of the car (which only works on a bumpy gravel road).
    THE CART absolutely must be running on all 4 rail wheels, not the fronts and rubber drivers
    The drivers will be held to the rail by suspension pressure only, and should my I say, have a retraction system, whereby you can raise them slightly, whenever you wish to hand push thecart (without the rubber wheels causing drag).
    Have fun after that, knowing that the FLANGES also have another expremely important job, that if they are NOT "just inside gauge" but not deep enough either, you will NOT get past the turnout frogs of any switches..
    The flanges work on BOTH faces, to travel between the running rail and the check rails - holding the wheels to whichever way the turnouts are set, such that the gap at the frogs cannot derail you.

  • @x9x9x9x9x9
    @x9x9x9x9x9 21 день назад +6

    Never seen this channel but this guys positivity and just attitude is amazing and infectious.

  • @jeffshowers1006
    @jeffshowers1006 16 дней назад +8

    Your wheels need to be pitched to 72 degrees. The wheels not only act to center but as differentials during curves

    • @robertramsey4079
      @robertramsey4079 16 дней назад

      not true

    • @SilvaDreams
      @SilvaDreams 16 дней назад +2

      THe irony is that those rims would have worked better than a wheel he made.

  • @nightrunner823mcpro2
    @nightrunner823mcpro2 20 дней назад +4

    I don't think I've ever seen a more negative comment section holy shit. You guys did great and the fact you even got it working is fantastic! It looks fun, it's nice and compact, and it works, that's exactly what you set out to do, don't let these comments discourage you from making more crazy stuff! I love your sense of humor and your excitement and of course it's not like you're a crazy engineer so it's okay to make mistakes. The people in the comments may help but I definitely think some of them are some straight up assholes. Love it, keep up the work!

    • @jettluft157
      @jettluft157 20 дней назад +1

      Actually! Everyone's so negative. They did an awesome job. I thought it was sick!

  • @tadnauseum
    @tadnauseum День назад +6

    Love the never give up and self reliance, but why are all diy youtube rail projects just: I'm going try stuff until I concede that rail design happened 200 years ago and I can just do that.

  • @alecfromminnenowhere2089
    @alecfromminnenowhere2089 20 дней назад +1

    Resilience is the sign of a good engineer. You weren't going to let little things get you down.

  • @curtisnewton895
    @curtisnewton895 20 дней назад +12

    I dont understand why you thought wheels without lips would make it, come on

  • @TheoTheFox.
    @TheoTheFox. 16 дней назад +11

    1:22 She's gonna give you WHAT?!

    • @briegell1
      @briegell1 14 дней назад

      Part 2 is on pornhub...

  • @pinealism
    @pinealism 21 день назад +4

    This is super fun, from an engineering point of view i want to point out everything wrong, but also just enjoy how bad engineering still basically gets the job done😊

  • @ThinkerOnTheBus
    @ThinkerOnTheBus 20 дней назад +2

    I believe if you would have used something to vibrate the plaster immediately after pouring, or used a hammer to rapidly beat on the side of the bucket, you can get most of the air bubbles to shimmy up to the top of the mixture, and leave. Next, are you making your wheels conical? If you want your car/cart to roll smoothly, especially around bends, and you want it to quite literally correct itself automatically to stay on those rails! The cone shape of the wheels will serve as a differential when turning. For when you turn, the outer wheels will travel a greater distance through the entirety of a turn than the distance traversed by the inner wheels, and because they both will spend the same amount of time turning, the outer wheels will be rotating at a greater speed than the inner wheels, and that is the purpose of a differential in vehicles, it allows the wheels on the same axle to independently travel at different speeds from each other. Differentials are some incredibly clever mechanisms, but I believe the conical wheels of a train is even more clever! The cone shape of the wheels create a range of different sized circumference, and this is how two wheels attached to the same axle that will always rotate at the same speed as the other. However, as it rotates around a turn, the wheel on the inside of the turn will follow the path of the least resistance, and it will naturally be pulled to rolling over the rail on the smaller end of that wheel, while the outer wheel will be pulled toward its bigger end, and in so doing, while both wheels are rotating at the exact same speed always, the outer wheel making contact with the rail at its thicker end translates into one rotation of the wheel traveling a farther distance than the distance that the inner wheel can travel in one rotation at its skinnier end. As for the physics behind how such shaped wheels can autocorrect the cart's direction of travel in relation to the track. However, I'll post a link to a short video that will explain it better than I can . . . that is if I can find it.
    Actually, take your pick:
    ruclips.net/video/XzgryPhtc1Y/видео.html
    ruclips.net/video/HeDuGWNTDPY/видео.html
    ruclips.net/video/DzdGKC344YI/видео.html

  • @kalhoon
    @kalhoon 11 дней назад +4

    Use the cart rims ,cut down centers so metal edges work as a guide to keep it on track. Use motorcycle spring shocks on rear guide wheel to keep tension. Rail wheels have a lip on inside edge to keep on track. Welding a steel plate on inside of rim and using rubber wheels will work.

  • @BlackThunderRC
    @BlackThunderRC 21 день назад +9

    Steel wheels are a must

  • @parkour6446
    @parkour6446 17 дней назад +3

    I was engrossed the whole time and your love for not only what you do but also life is abundantly apparent. Keep up the good work, you're doing great!

  • @ChainsawFPV
    @ChainsawFPV 21 день назад +5

    Thats very cool, but looks a little heavy to pick up, and go around obstacles. At least need some large caster wheels on all 4 corners on jacks that can lift it off the tracks, and roll it around. Use steel guides to keep it centered to. They wont wear out after time.

  • @mathiasrasmussen7455
    @mathiasrasmussen7455 19 дней назад +8

    No idea what you where thinking going without flanges.. There is a reason why rail tracked things have them. 😅

    • @mlindholm
      @mlindholm 19 дней назад

      The flanges are a belt-and-suspenders approach, but aren't the primary reason they stay on the rails. The tapered wheels are what keep trains on the rails, but also allow them to go around curves.

  • @kevinpts9932
    @kevinpts9932 22 дня назад +18

    THERE SHOULD BE A DRINKING GAME FOR THIS VIDEO. EVERYTIME HE SAYS PUPPY .................DRINK

    • @MattSpears
      @MattSpears  22 дня назад +2

      hahahah

    • @cabbelos
      @cabbelos 21 день назад +1

      In this video everything else was a puppy except the dog

    • @Deltakitty32780
      @Deltakitty32780 21 день назад

      😅😅😂😂😂

  • @jeffmentzer6550
    @jeffmentzer6550 21 день назад +7

    you have room on the back for a small gas powered motor to run a third wheel in case your original battery gives out

  • @yokelabductee
    @yokelabductee 21 день назад +5

    i'm screaming "guide wheels behind the drive wheels to maintain traction when going in reverse"

  • @lourenco3216
    @lourenco3216 6 дней назад +4

    One big problem is having rubber wheels instead of metal.
    Metal on metal has less friction and allows the wheels to slide on the rails and adjust the cart position to be centered.
    Ruber has the opposite effect instead of pushing the cart to the middle they pull it outwards.
    Your grooves managed to work but I wouldn't recommend it to others.

  • @ortonscustoms2577
    @ortonscustoms2577 24 дня назад +3

    Props for learning to tig last night and actually producing some clean enough welds

  • @wolffang489
    @wolffang489 4 дня назад +2

    Every single concern and thought I had about the wheels as you were making them you acknowledged at a later point. Well thought out and executed project especially for something experimental. I can't say I've seen a lot of rail car videos but this was the best of the ones I have!

  • @edrogers9530
    @edrogers9530 23 дня назад +8

    At the 16 min mark, You mention train wheels being angled or convex which keeps them straight on track. The reason is actually to do with going around corners, One wheel travels a further distance.

    • @markellii3093
      @markellii3093 23 дня назад

      Isn't it like, both?

    • @edrogers9530
      @edrogers9530 21 день назад

      @@markellii3093 Sort of, They needed a way to stop one wheel from skidding around a corner as train wheels do not have a differential.

  • @lhurst9550
    @lhurst9550 3 дня назад +4

    The problem here is abandoned rails are not maintained.

  • @JustLiv-ri8jl
    @JustLiv-ri8jl 20 дней назад +3

    I love how you say "Babe just mustered up the strength of a small giant".... You call her "babe" on video. That's so sweet and cool. Also, you are SO close with the tapered wheels. That's what trains have. But you need and inner flange to prevent derailment. For this non-steel wheel design, you would need to add a steel flange to the inside. The flange can't be made of that epoxy it would break off. The flange takes rare but large forces. But awesome video. I'm subbed.

  • @vale-1041
    @vale-1041 20 дней назад +5

    I don't get why there's so much hate in the comment section. I thought the video was great! Yes, real train wheels would have performed better with less work, but you altered your failed attempts into something that works! People seem to have missed the part of the video that you mentioned the wheels, and also seem to have missed the part where the vehicle isn't a 10,000 ton rail car.
    Really interested to see what comes next!

    • @99milesaway41
      @99milesaway41 20 дней назад +1

      Sadly, people will take any excuse to throw hate. The guy is learning as he goes, in my opinion, that makes the best videos, you get to see how not do parts, as well as the success.

  • @ulerhond
    @ulerhond 21 день назад +4

    I think if I were you, I wouldn't have cast the front wheels in resin and just used the rims to keep it on the track, OR put a plate behind each of the 4 wheels that are larger in diameter so that they can be the track guides. Would be interesting to see how it would do after that.

  • @houi4900
    @houi4900 17 дней назад +9

    YEAAHH GALVANIZED SQUARED STEEL !!!! 2:35

    • @JustNex_
      @JustNex_ 17 дней назад +1

      YEAHH

    • @lucxsbain
      @lucxsbain 17 дней назад +1

      I went looking for this comment

  • @J_Gurn32
    @J_Gurn32 21 день назад +14

    Dude you're gonna wreck your back if you keep doing that. Seriously.

  • @danemonium
    @danemonium День назад +3

    Dear Lord enough with the puppies!!!

  • @GregAtlas
    @GregAtlas 22 дня назад +4

    If you did decide to buy a rail wheel, I suggest buying only one and then casting a mold in silicone. Then you can make replicas in your resin material for a more pleasant experience than metal on metal AND have a easy way to replace wheels that have been damaged.

  • @robhicks2117
    @robhicks2117 19 дней назад +6

    Why don't you buy some steel track wheels? $52 each at Grainger Inc.

  • @jamiew1555
    @jamiew1555 22 дня назад +10

    How many puppies does it take to build a rail car??

    • @alexmikhael5061
      @alexmikhael5061 22 дня назад +1

      ALL OF THEM :) well ENUF of them ...eh... lol hahahaha
      HAVE A WONDERFUL DAY !!!
      LOVE JOY COMPASSION

    • @MattSpears
      @MattSpears  22 дня назад +1

      about 27!

  • @Stevexeairoux-hw8sx
    @Stevexeairoux-hw8sx 22 дня назад +3

    Definitely should use steel flanges on the wheels. May think for the long haul and get a solar panel to help charging spare battery bank.

  • @CptFUBAR
    @CptFUBAR 17 дней назад +3

    This editing is actually really good. Nice and concise, but still adding the bits and bobs that add humor and shows progress. Glad that algorithm steered me to ya!

  • @thra5herxb12s
    @thra5herxb12s 8 дней назад +4

    Awesome ride. The wheels need strong metal flanges for a reason, there's a heck of a lot of strain on them trying to keep it all straight.

  • @wayneschenet5340
    @wayneschenet5340 День назад +4

    Where is the location of this abandoned rail line?
    Where are the end points? And how many miles can you go?
    Cast metal wheels with flanges will solve your problem.

  • @Ipoetize
    @Ipoetize 17 дней назад +3

    What's not to love about this guy? Just this one example @7:57 - 8:02 should be enough, I mean come... How often do you see that level of joy emanate, rise up, and burst out of someone like that? That is a benchmark moment right there, for sure. So I say: Keep shining and smiling because the world needs more of it. Thank you for sharing and salute you I do!

  • @lockout6896
    @lockout6896 23 дня назад +4

    “I literally learned how to rig welding last night” dudes killing it

    • @DonWRII
      @DonWRII 23 дня назад

      I was thinking his welds looked really good for learning TIG overnight, though he didn't go too close to them, but they seemed to hold up until the crash. I think TIG aluminum might have been to save the weight with the little cart

    • @Aimaiai
      @Aimaiai 21 день назад

      @@DonWRII some people are just mechanically gifted like that lol, i sharpen hockey skates and when I train new hires its clear who will take 1 hour to learn vs 10 hours to learn, probably exactly the same as welding.

  • @Rydsfar
    @Rydsfar 22 дня назад +4

    So, maybe you already know this, but the taper of the wheels isn't really to center the car on the rails. It's how the outside wheels are able to turn faster than the inside wheels when cornering. So, if you get that angle right, your wheels won't wear as badly from going around the curves. And steel would definitely be a better choice, but skaters be skatin'...lol

    • @MattSpears
      @MattSpears  22 дня назад

      Ohh yeah! I think eventually I need to make 4 wheels all being the same size and taper

    • @maarten_notjustagrip
      @maarten_notjustagrip 22 дня назад

      Steel wheels are HELL to ride on. VERY bumpy, VERY noisy, UNLESS you fit a tyre of some sort. PU is best for that. It also gives some traction. Our rigs dont weigh 28 tons like a loco does. Bigger diameter definitely helps too.

  • @semaja2
    @semaja2 20 дней назад +5

    For some reason these little rail car videos are popping up in my stream, the big question I have for all of them... why do they all avoid doing any research to understand how trains stay on a track, they have metal with designed flanges that let them turn and stay on tracks etc

  • @ChancellorBeeHaw
    @ChancellorBeeHaw 24 дня назад +2

    love this format and style you’re adopting on youtube, definitely think you’ll continue to bring in new people! :)

  • @theone2be33
    @theone2be33 24 дня назад +5

    Dude! You've had that thing in the water, on the train tracks, if you make it fly next would be HILARIOUS!

  • @WillowEpp
    @WillowEpp 22 дня назад +4

    In this video: kids discover rail transit is actually really great.

  • @leonvanderlinde5580
    @leonvanderlinde5580 21 день назад +6

    Why do you think they have flanges on the wheels. To stay on the track.

  • @emilflognoid1532
    @emilflognoid1532 21 день назад +5

    My only criticism is you didn't paint it like lightning McQueen

  • @incipfer
    @incipfer 6 дней назад +3

    Trains have solid axles with both conical steel wheels locked to the axle because a trains wheels have to spin faster/slower to turn on a railway. Plus a railway is larger than the wheels so the train actually self centers on the track.

  • @johnnyrotten3175
    @johnnyrotten3175 17 дней назад +4

    Love the show. Some great ideas. Three things I noticed. Some Bearings to reduce axle heat. Wheels need a lip on them to keep them on the track. Track is not always straight, so Front suspension needs a central mounting bearing to allow for crack turns.
    Looks like a lot of fun! Keep up the great work, and see you next time 💯

  • @thepagan5432
    @thepagan5432 20 дней назад +5

    Where are all these puppies, you said it at least 50 times.😊

  • @cheeserdane
    @cheeserdane 21 день назад +5

    If you go anywhere overnight bring extra wheels

  • @lewisf1988
    @lewisf1988 17 дней назад +6

    we need a "puppy" counter haha!

  • @jonathanlove5430
    @jonathanlove5430 20 дней назад +6

    Crazy how much hate is in this comment section. Great job, thats so cool. Love the positive attitude

    • @CRSolarice
      @CRSolarice 20 дней назад +1

      Like yourself, everyone is entitled to state their opinion be it positive or negative; so as long as they aren't threatening to harm then all is acceptable.

  • @frogpit
    @frogpit 22 дня назад +12

    i lost count of "puppies"

  • @jmr1068204
    @jmr1068204 20 дней назад +4

    "When this baby hits 88mph... *you're going to see some serious sh!t!* "

  • @nickalderman5943
    @nickalderman5943 2 дня назад +2

    this is sick, toss a few solar panels on a trailer with something like an eco flow house battery and you're good for overnighters. Will even have storage under the panels.

  • @jamesfletcher279
    @jamesfletcher279 22 дня назад +9

    Great project but please please young man stop lifting like you are doing as when your older your back is going to give you some serious problems

  • @claytonsimplot9554
    @claytonsimplot9554 17 дней назад +4

    Why not use riding lawn mower tires and rims? Install an inside flange on each rim. Smoother ride.

  • @gogofuntime_yt
    @gogofuntime_yt 21 день назад +3

    I like this guy's channel. I hope he gets the subscribers he deserves.

  • @ReverendNaughty
    @ReverendNaughty 21 день назад +3

    I have a picture of me sitting in that car from the St. Louis Motorcycle Show like 11 years ago... Never figured I'd see it on youtube going on train tracks, lol.

  • @reffmatt1296
    @reffmatt1296 22 дня назад +3

    this videos make me wish that italy had empty railroads...

  • @TheBamaChad-W4CHD
    @TheBamaChad-W4CHD 19 дней назад +3

    I waited patiently for you to figure out that you can't allow your rubber wheels to be load-baring because they won't slip to fit the metal tracks. There are many reasons why trains still use steel on steel today!

  • @djfrogsak
    @djfrogsak 22 дня назад +3

    need to make the drive wheels wider and more rigid, you can see them trying to "fold over" under themselves when you were lifting it back onto the track, them rear wheels need to be braced better as well, the more rigid it is, the longer it will stay on the rails, proper rail wheels will solve alot of your issues with derailing, also, if you making the rail riding gear retract upwards when not being used, would be great, so when you want to turn around, find a road/rail crossing, raise the rail wheels, drive onto the road, turn around using the normal road wheels, line it back up, lower rails, off you go again, (check out ride on mowers for the idea on how to make it work, raise and lower cutting deck) will save having to bring a small squad with you just to get it turned around, and lastly, you will want the rear rail wheels to be able to turn with the corners of the train track, so a pivot point in the middle with spring holding it straight should do the job perfectly, they only need to turn like 10 degrees, maybe less than that, but ti will help when cornering on the railroad tracks, once you have done all the upgrades i have mentioned, you should be able to install a bigger motor and go much faster safer..... 👍👍

  • @thedomesticoperator
    @thedomesticoperator 15 дней назад +7

    Redesign with nose windows like a helicopter so you can see your wheels or other obstructions.

  • @RussellNelson
    @RussellNelson 20 дней назад +7

    34:35 "it goes straight and it bounces". That's called "hunting". If your wheels were a proper shape, that wouldn't happen as much.

  • @DynamicHaze
    @DynamicHaze 17 дней назад +6

    Definitely need some metal wheels. With a lip.

  • @randomguy2925
    @randomguy2925 22 дня назад +5

    The wheels need to be out of metal, and they need a bigger plate at the end to stop it derailing. Good luck

  • @mikeholley4488
    @mikeholley4488 20 дней назад +5

    do same ride at night with night vision. You'll see lots of critters. No other vehicles, too much noise