This is such a poorly done repair. It'll break in no time and they'll get to do it again. To anyone saying they have to make do with what you've got, that's no excuse for not even cleaning the dirt off before they weld.
If i heard correct, those "teeth" should be made of molybdenum because of its work hardening property. I wonder what was the material of the ones they used
@@henryrollins9177 excavator that size is used for digging on hard shit 8hours pers Day. And Even If it was used for some fucking "soft" material bullshit you just dont repair goddamn excavator buckets like this just for The sake of principles.
@@enemyplayer7293 мне и работать не надо на ковше ,клиновидные элементы изготавливают так чтобы у тебя шла не прямая плита в стык к стыку а так что бы получались зубья в виде буквы П с шагом не менее 15-20см с обязательным снятием в месте свариваемых деталей с обоих сторон технологических фасок ,тут всё рабочее усилие приходиться на боковые свариваемые детали малейшая трещина хотя бы на одной стороне приведёт к потере полностью всей рабочей поверхности так деталь не проварена полностью а лишь поверхностно ,если хочешь поэксперементировать возьми два куска пластика и спайку проведи как тут и попробуй сломать лопнет даже секунды не пройдёт а сделай шов в виде П_П_П и со снятием фаски и полным заполнением шва то так просто ты уже не сломаешь деталь и тебе всё таки придётся приложить усилие
@@enemyplayer7293 и меня не надо разводить на рассказы как надо ,у вас вон новых инженеров с ЕГЭ институтами дохуя развелось как собак недобитых ,один молотком двигатель от стиральной машины пиздит потому что ума нет снять шпонку другой в токарный станок пластиковые шестерни пристроить надумал а станок два дня даже не отработал отрыгнул всю его взаимозаменяемость и ложил болт он на утверждение что там нет нагрузки ,а по итогу результат один машины есть а не работают ,вам же не надо чтоб работало надо чтоб ломалось вот так работаете
Ладно бы ещё кругляк был.В кругляке сталь вязкая,ещё прокатит.Но в периодичке сталь другая!Шов там сто процентов лопнет!Именно из-за качеств этой арматуры. А вцелом по работе,одно слово только на уме:кустарщина.
Two things,first heat the grosers up first they go on alot easier,second why are you welding the grosers on?,they are meant to be breakaway...going to be a pita to swap them when you break on 15 minutes into digging
I agree with James Ratliff. What has to be understood here is perhaps there is not a lot of money to spend on proper teeth and so have to use what they got. Not everyone has the luxury of having access to all the gear that's why they are stick welding. And so in all fairness they have done a good enough repair. The machine can go and dig a hole. What more do you need.
@@sigsauer9mm957 just for the record. When i said thats why they are stick welding i was not knocking the process. Just saying that is what they had they did a far better job then i could have. Because i am only a hobby welder. If in future you haven't got anything good to say about my welding. Or anybody else better you said nothing at all.
Yes sig I know what stick welding is. Most welders who have access to mig will weld a bucket because it is faster. As long as you have the right gas and wire. Nothing wrong with arc or mig. I smoke lambert and butler ciggies not crack. Thanks for your comments though 👍
@@ruthbees7214 There's no qualified welder in the world who would weld that bucket with MIG. Are you just getting into welding? Maybe you're confusing MIG for Flux core? Flux core might look like MIG but there's no gas (the flux is inside the hollow wire). It's an alternative to stick welding because it can be faster. Other than that they ONLY way to weld that bucket is stick welding. You cannot use MIG for a job like this as it wont penetrate and it's not strong enough.
@@noteasybeingcheesy2673 hi cheesy i am no expert in welding. I was thinking of dual shield or flux core when i said mig welding this is what i ment by it just to clear up any confusion. Thanks ruth😁
@@ruthbees7214 You're welcome, no problem. The dual shield (flux core with gas) is alright indoors (no wind to flow the gas away) and it may look cleaner. It's not a as strong as flux core (no gas) though. For structural (or anything which needs to be strong like that bucket) there's really only two ways go: stick or flux core. The only real advantage to flux core is that it can be faster (so if you're working on a huge structure it would save on costs/time). Other than stick (which is the method I would choose for this bucket) it might be the way to go in terms of cost/time on a big project. You have to also consider the advantages of the stick itself vs a gun/nozzle. Stick is 14 inches long with common diameters of 3/32 to 5/32. You can weld areas where the gun/nozzle cannot reach or even if does you cannot get a good angle or you can barely move at. Another note on this video is that there should be more beveling. On something like that bucket (it's going to support heavy loads) you need full penetration. You can't just welding the top and bottom and leave a hollow space in the middle. The stick will of course penetrate (depending on which type of electrode you're using) to some degree but on thicker medal you need bevel well. Apologies for any spelling and grammar errors in my comments. I did go to college for a little while (sociology) but dropped out after I realized I'd rather work in a skilled trade and get some excerise and see the world.
Muy mala reparación. Esa pieza se romperá en poco tiempo. No se preocuparon ni de hacer un chaflán para la soldadura y seguramente pusieron cualquier tipo de acero en la parte delantera. Por otro lado, los electrodos son rutilos y no básicos. Por supuesto, no hicieron radiografía de la soldadura ni un ultra-sonido porque no hubiera sido aceptada. Una reparación así es perder el tiempo.
Anyone see a good reason to remove the bucket from the trackhoe for this repair? Or do they just like pounding pins and rolling huge chunks of steel around in the dirt..?
Designed and engineered in Japan, sold second hand to China, worn to the bone and sent to die in Pakistan. The metal recycling industry there must love these "street repairs." Absolutely no prep work done or concept of heat tempering fatigue.
That is not how you repair or replace the teeth on a bucket. Not only did you ruin the integrity and value of the bucket, but you spent much longer doing it. Isn't there anybody to teach these people in third world countries how to properly prepare a weld and or fix and replace parts on a bucket?? You never praise bad work or bad behavior. The people who are giving a thumbs up to this kid have no idea what they're looking at.
You took the words right of my mouth ... I've watched many of these kind of videos that YT is bombarded with ... most of the repairs are poorly executed and sometimes dangerous ... the funny thing is that they make so many views and likes and even good comments ...
they have to work with what they have or have access to , they dont have the same shops/infrastructure and things like that that many other countries have
If these guys had some tools like an overhead crane, even an oversized engine lifting portable crane it would be amazing the amount of work they could get done. Great work. If I were offering any advice it would be to radius or round off the outer part of the bucket cutting edge so the teeth could get all the way onto the edge. It would give a little more surface to weld and no gap. But great job.
So much fail, the teeth are not supposed to be part of the bucket, they are supposed to be replaceable. They are the first thing that wears down, and should be replaced when worn, to prevent this kind of work needling to be done.
Super sh-tty. They basically glued the top and bottom of the plate. No bevel. At best maybe 60% penetration. And buy a welding helmet. That hand held thing might be ok for tacking or a very short bead but not for burning rod and continuous rod.
No bevel. No pre-heating. What type of rod? Should be using 6011 for the root and 7018 for the filler and cap. And rebar in the grove? Yea, that will hold up to moving sod out of the way. And radius those corners. That plate will get ripped off once it is used for hard clay or concrete/asphalt.
I gotta say, these guys are usually pretty good considering their conditions.. but these excavators require high level welding technique. Beveling is critical.
How is cutting half the bucket off and poorly welding on a sad set of teeth more efficient than just replacing the tooth that needs it especially if none of them need it.. you know ..if it ain't broke.. dont hack it up
Any job worth doing is worth doing properly. Too poor to afford new? How about a proper repair. This is a money wasting process. Whit what this customer will end up spending over the year, he might as well get a new bucket......... And, damn - no safety considerations at all. I don't watch these videos to learn or enjoy seeing quality work done - I watch them kind of like I like to watch monkeys and cats. Shenaganins.
GREAT WORK, THE CUTTER WHAT A JOB. I DRINK TO MUCH COFFEE. NOW IF I HAD WELDED THAT WITH THE PIECE OF RIB BAR. IT WOULD HAVE BROKEN THE SAME DAY. OUTSTANDING WORK. I ALWAYS ENJOY SEEING THESE GUYS WORK. GOD BLESS THEM ALL.
How strong are those welds going to be? A domestic power supply can't offer enough amps to penetrate those parts enough surely. Plus clean the parts to bare metal. It will give a MUGH stronger weld. You have a grinder at hand already. Overall nicely planned work but Exekution leaves me tonwonder how well it will last.
01:58 Tem pessoas que falam que tem que encher de solda em chapas grossas. Que dessa forma aí do vídeo a solda fica superficial. Que teria que fazer uma fenda na emenda, e ir enchendo de solta até a superfície, para ficar soldada por completo. Será que assim como eles fizeram fica soldada por completa também?
Hats off to this young guy who repair jiant excavator bucket..👍👍👍
Thanks you dear
That's a small bucket my friend!
@@RandomTalent no proper PPE
This is such a poorly done repair. It'll break in no time and they'll get to do it again. To anyone saying they have to make do with what you've got, that's no excuse for not even cleaning the dirt off before they weld.
Best techniques I've ever seen. Great job guys👍
Shut up.
@@koistinen9368 Looks like it is used for soft material...look at the thin and pointy tooth they installed.
I say it will work well!
If i heard correct, those "teeth" should be made of molybdenum because of its work hardening property. I wonder what was the material of the ones they used
@@henryrollins9177 excavator that size is used for digging on hard shit 8hours pers Day. And Even If it was used for some fucking "soft" material bullshit you just dont repair goddamn excavator buckets like this just for The sake of principles.
A piece of high quality rebar to fill the gap, hope they don’t grab anything harder than topsoil.
Lol
Considering the teeth are made from reforged railroad tracks (different video), there's a number of failures possible if they dig anything too firm.
I had a good laugh at that bit lol. Poor barsterds though, must struggling if they are using that.
FCC
I was thinking the same thing. That rebar was never intended to be welded and severely compromised by doing so
Такой ремонт 🤦🏻 без разделки кромок , метал не зачищают 🤦🏻
Каста гнутого электрода)))
А зачем они его гнут?
Почти во всех видео замечал
Сам сварной не понимаю нахрена гнуть если доступ к шву открыт.
Очень часто вижу людей которые курят. Так вот суют сигарету в ротик и дуют в фильтр. По какой причине так делают не знаешь?
Такой ремонт не надолго ,не снята фаска на свариваемых деталях ,нет клиновидных усиливающих элементов снизу ковша
а ты работал на ковше?)))какие еше клиновидные там снизу?))))там рабочая часть)))
Одеты по традиции нации! Интересно почему , одежда не горит, и краги не нужны 🤔 !
@@enemyplayer7293 мне и работать не надо на ковше ,клиновидные элементы изготавливают так чтобы у тебя шла не прямая плита в стык к стыку а так что бы получались зубья в виде буквы П с шагом не менее 15-20см с обязательным снятием в месте свариваемых деталей с обоих сторон технологических фасок ,тут всё рабочее усилие приходиться на боковые свариваемые детали малейшая трещина хотя бы на одной стороне приведёт к потере полностью всей рабочей поверхности так деталь не проварена полностью а лишь поверхностно ,если хочешь поэксперементировать возьми два куска пластика и спайку проведи как тут и попробуй сломать лопнет даже секунды не пройдёт а сделай шов в виде П_П_П и со снятием фаски и полным заполнением шва то так просто ты уже не сломаешь деталь и тебе всё таки придётся приложить усилие
@@drakoshagamer3075 чистая одежда из хлопка что ты удивляешься
@@enemyplayer7293 и меня не надо разводить на рассказы как надо ,у вас вон новых инженеров с ЕГЭ институтами дохуя развелось как собак недобитых ,один молотком двигатель от стиральной машины пиздит потому что ума нет снять шпонку другой в токарный станок пластиковые шестерни пристроить надумал а станок два дня даже не отработал отрыгнул всю его взаимозаменяемость и ложил болт он на утверждение что там нет нагрузки ,а по итогу результат один машины есть а не работают ,вам же не надо чтоб работало надо чтоб ломалось вот так работаете
После того как засунул кусок арматуры в шов , смотреть дальше на халтуру нет смысла !
так он кареной шов заложил )))
Разделка кромок не не слыхал варить 20 тройкой это конечно сильно обломается эта липуха в скором времени
Ладно бы ещё кругляк был.В кругляке сталь вязкая,ещё прокатит.Но в периодичке сталь другая!Шов там сто процентов лопнет!Именно из-за качеств этой арматуры.
А вцелом по работе,одно слово только на уме:кустарщина.
Директор завода который выпускает эти зкскаваторы , наверно уволится , когда увидит этот ремонт.
В этом случае я на работе когда варю ковши обрезаю нож и подрезают бока дабы вставить полноценные куски метала а не эту хню с арматурой
Такой толстый метал без раскройки проварить просто невозможно это не провар в один шов это присераловка
Я работаю сварщиком 28 лет , но после такого , хочется сказать ""теперь я видел всё""!
А то что они варят там без маски? Одним словом Боливуд
Походу там всем пох.
Two things,first heat the grosers up first they go on alot easier,second why are you welding the grosers on?,they are meant to be breakaway...going to be a pita to swap them when you break on 15 minutes into digging
I agree with James Ratliff. What has to be understood here is perhaps there is not a lot of money to spend on proper teeth and so have to use what they got. Not everyone has the luxury of having access to all the gear that's why they are stick welding. And so in all fairness they have done a good enough repair. The machine can go and dig a hole. What more do you need.
@@sigsauer9mm957 just for the record. When i said thats why they are stick welding i was not knocking the process. Just saying that is what they had they did a far better job then i could have. Because i am only a hobby welder. If in future you haven't got anything good to say about my welding. Or anybody else better you said nothing at all.
Yes sig I know what stick welding is. Most welders who have access to mig will weld a bucket because it is faster. As long as you have the right gas and wire. Nothing wrong with arc or mig. I smoke lambert and butler ciggies not crack. Thanks for your comments though 👍
@@ruthbees7214 There's no qualified welder in the world who would weld that bucket with MIG. Are you just getting into welding? Maybe you're confusing MIG for Flux core? Flux core might look like MIG but there's no gas (the flux is inside the hollow wire). It's an alternative to stick welding because it can be faster. Other than that they ONLY way to weld that bucket is stick welding. You cannot use MIG for a job like this as it wont penetrate and it's not strong enough.
@@noteasybeingcheesy2673 hi cheesy i am no expert in welding. I was thinking of dual shield or flux core when i said mig welding this is what i ment by it just to clear up any confusion. Thanks ruth😁
@@ruthbees7214 You're welcome, no problem. The dual shield (flux core with gas) is alright indoors (no wind to flow the gas away) and it may look cleaner. It's not a as strong as flux core (no gas) though. For structural (or anything which needs to be strong like that bucket) there's really only two ways go: stick or flux core. The only real advantage to flux core is that it can be faster (so if you're working on a huge structure it would save on costs/time). Other than stick (which is the method I would choose for this bucket) it might be the way to go in terms of cost/time on a big project. You have to also consider the advantages of the stick itself vs a gun/nozzle. Stick is 14 inches long with common diameters of 3/32 to 5/32. You can weld areas where the gun/nozzle cannot reach or even if does you cannot get a good angle or you can barely move at. Another note on this video is that there should be more beveling. On something like that bucket (it's going to support heavy loads) you need full penetration. You can't just welding the top and bottom and leave a hollow space in the middle. The stick will of course penetrate (depending on which type of electrode you're using) to some degree but on thicker medal you need bevel well. Apologies for any spelling and grammar errors in my comments. I did go to college for a little while (sociology) but dropped out after I realized I'd rather work in a skilled trade and get some excerise and see the world.
Muy mala reparación. Esa pieza se romperá en poco tiempo. No se preocuparon ni de hacer un chaflán para la soldadura y seguramente pusieron cualquier tipo de acero en la parte delantera. Por otro lado, los electrodos son rutilos y no básicos. Por supuesto, no hicieron radiografía de la soldadura ni un ultra-sonido porque no hubiera sido aceptada. Una reparación así es perder el tiempo.
Anyone see a good reason to remove the bucket from the trackhoe for this repair?
Or do they just like pounding pins and rolling huge chunks of steel around in the dirt..?
А старые зубы чем не угодили?
Designed and engineered in Japan, sold second hand to China, worn to the bone and sent to die in Pakistan. The metal recycling industry there must love these "street repairs." Absolutely no prep work done or concept of heat tempering fatigue.
Anh thợ Hàn gàu xe cuốc rất chuyên nghiệp
That is not how you repair or replace the teeth on a bucket. Not only did you ruin the integrity and value of the bucket, but you spent much longer doing it. Isn't there anybody to teach these people in third world countries how to properly prepare a weld and or fix and replace parts on a bucket??
You never praise bad work or bad behavior. The people who are giving a thumbs up to this kid have no idea what they're looking at.
Actually,it s need of our country..but we are improving with the passage of the time..but it will take time..
You took the words right of my mouth ... I've watched many of these kind of videos that YT is bombarded with ... most of the repairs are poorly executed and sometimes dangerous ... the funny thing is that they make so many views and likes and even good comments ...
they have to work with what they have or have access to , they dont have the same shops/infrastructure and things like that that many other countries have
@@melin1969 the internet exists for a reason lol
Work and you’ll get what you need; work harder and you’ll get what you want.
😘
Apparently Elon Musk worked 24 hours a day all his life that earned 300 billion)
If these guys had some tools like an overhead crane, even an oversized engine lifting portable crane it would be amazing the amount of work they could get done. Great work. If I were offering any advice it would be to radius or round off the outer part of the bucket cutting edge so the teeth could get all the way onto the edge. It would give a little more surface to weld and no gap. But great job.
The original didnt look bad enough to cut off like that
So much fail, the teeth are not supposed to be part of the bucket, they are supposed to be replaceable. They are the first thing that wears down, and should be replaced when worn, to prevent this kind of work needling to be done.
Large scale dentistry ! 🦷🦷
For crying out load…….where’s his sandles
Probably use for sand or mud
Super sh-tty. They basically glued the top and bottom of the plate. No bevel. At best maybe 60% penetration. And buy a welding helmet. That hand held thing might be ok for tacking or a very short bead but not for burning rod and continuous rod.
Фаску же надо снять перед сваркой, металл толстый
No bevel. No pre-heating. What type of rod? Should be using 6011 for the root and 7018 for the filler and cap. And rebar in the grove? Yea, that will hold up to moving sod out of the way. And radius those corners. That plate will get ripped off once it is used for hard clay or concrete/asphalt.
beginner here, why the 6011 for the root?
I love these kids yelling on the internet
I gotta say, these guys are usually pretty good considering their conditions.. but these excavators require high level welding technique. Beveling is critical.
до этого считал их гениями.но это жесть и колхоз ремонт
Я вообще не понял, нахрена они туда лезли. Нормальный же ковш был.
@@sergeypiletskiy1022 может специфика работ поменялась,
The old bucked was better without adjustment...
Gotta have that bent rod. Doesn't anyone have a chipping hammer? Poor repair in so many ways.
This work will never be ok!!
this is one of the first videos that the workers had googles and boots
Buen trabajo. Me gusta.
Несмотря на то что экскаватор приехал сам в город ,сварка полное дермище слесарки ваше нет.результат отломанные зубы через день.
старый ковш переплавили и сделали тормозные диски BREMBO
Лучше бы вообще не делали, чем так... Не понимаю я их привычку все в песке ремонтировать.
You know the toothbrush was invented in West Virginia because if it came from anywhere else it would have been called the teethbrush
ОТЛИЧНО !!!!! ПРИВЕТ ИЗ РОССИИ !!!!🇷🇺 🇷🇺 🇷🇺 🖐️🖐️🖐️👍👍👍
How is cutting half the bucket off and poorly welding on a sad set of teeth more efficient than just replacing the tooth that needs it especially if none of them need it.. you know ..if it ain't broke.. dont hack it up
Está muy bien hecho el trabajo.
Резка похожа на мечь ждедая) если не смотреть как режут. А смотреть уже на результат. То как от меча джедая след.
Wielki szacunku dla was 👍👍👍👍
зачем гнуть электроды
Welding in a steel bucket. Thats how I used to get a badass tan. The UV cooks you when it can reflect off of everything.
they already have a tan.
No good!!! up to 10 i rate 2
песок и глину ковырять пойдет))
Ухх.. кудаж такие зубы)))
1:58 Typical bodge it job
Amen🙏🙏🙏🙏🙏🙏👍👍👍👍👍👍👍👍🙏🙏😍😍
No bevel just straight thru...
На коленке без защитных средств....Жесть даже для России
Now thats a welding mask take that Lincoln Electric
Not the best techniques or materials so the bucket cannot be expected to last. They have to work with what they have l suppose.
It is what it is
Great temporary fix.
Таково толстово металу заварил без фаска проста так 😲. Это адаптер или коронка я не понял 🤔
Это хууууииитттаа
7016도장봉도아니고 오느천년에용접을다한다 말이고 한국에서는결코용납되지않는작업이다
Any job worth doing is worth doing properly. Too poor to afford new? How about a proper repair. This is a money wasting process. Whit what this customer will end up spending over the year, he might as well get a new bucket.........
And, damn - no safety considerations at all.
I don't watch these videos to learn or enjoy seeing quality work done - I watch them kind of like I like to watch monkeys and cats. Shenaganins.
تبارك الله
As the great John McEnroe once said You Can't Be Serious.end quote.
Глаза.......
Вот теперь экскаваторшику надо вырыть яму там и закопать сварщика
Hoy protect you eyes and hand dangerous job not Good safety first
Good Work 👍
Thanks ✌️
Flama cutting or plasma cutting
Very thin welds for my taste...
That definitely is “random”… I’m not so sure on the talent part 👀😂😂😂
Good Work
Thanks for the visit.
GREAT WORK, THE CUTTER WHAT A JOB. I DRINK TO MUCH COFFEE. NOW IF I HAD WELDED THAT WITH THE PIECE OF RIB BAR. IT WOULD HAVE BROKEN THE SAME DAY. OUTSTANDING WORK. I ALWAYS ENJOY SEEING THESE GUYS WORK. GOD BLESS THEM ALL.
Great idea
You are right about the rebar used as a filler. That weld will crack. It's just a matter of time.
Worst thing is the guy probably thinks hes doing it the correct way.....
yup...that looks factory original :)
Это не долго будет держаться такой лист 5 варить нужно минимум
Now, brush regularly and stay away from sweets!
How strong are those welds going to be? A domestic power supply can't offer enough amps to penetrate those parts enough surely. Plus clean the parts to bare metal. It will give a MUGH stronger weld. You have a grinder at hand already. Overall nicely planned work but Exekution leaves me tonwonder how well it will last.
Всё отлично,только на дворе 21век,а маска из прошлого!!!
Can anyone explain why they bend the electrode part way sown the rod please?
It's.thetechnic.of.oldwelders.who.taughtwelding.in.indian.country.1980s
this is how the jawas got their start
Thats some long tooth on bucket lol...
They destroyed the bucket. 🤣🤣🤣 Totally improper method.
Gloves nya gk di pakai bro. ? Mesti full safty 😁✋🇮🇩
다른의미로 대단하네
Kullanılan kaynak elektrodu, yapılan işe göre ince gibime geldi.
😁👍
Maybe some day they'll figure out sacrificial teeth that take a couple hours to replace.
Страна карталей и кривых электродов.
01:58
Tem pessoas que falam que tem que encher de solda em chapas grossas. Que dessa forma aí do vídeo a solda fica superficial.
Que teria que fazer uma fenda na emenda, e ir enchendo de solta até a superfície, para ficar soldada por completo.
Será que assim como eles fizeram fica soldada por completa também?
Watching the guy grinding with no glasses was cring worthy. Yikes.
Sama saya juga memperbaiki big bucket PC 2000 komatsu
♥️♥️♥️♥️♥️♥️
Pepe gotera y otilio
А нахрена они электрод гнут?🤣
Им же не обьяснили что можно держак повернуть, да и электроды наверно в саседней комнате изготавливают из бамбука вот и не экономят)))
Nice work very amazing
Thank you very much!
Когда отрезали зубья у ковша, я думал они сейчас казан делать будут ))))
Butt welding without even beveling the work is no bueno
Как дела?
Anjay kagak di bepel ahahaha dalemnya kosong laslasan
они знают что такое фаска?
Onde é que você mora
👍🏻
ماشاءاللّٰه
Thanks you dear