Clap Switch circuit on Breadboard (Sound triggered LED) | Transistor + 555 timer projects
HTML-код
- Опубликовано: 4 окт 2024
- A tutorial on How to make a Clap Switch circuit aka Sound Triggered LED, along with detailed explanation on how the circuit works. The sensitivity or Range up to which the circuit detects claps can also be adjusted.
You can also modify this circuit into a Clap On Clap Off switch by coupling the primary output of this circuit to 4017 IC. (Will make a tutorial on this soon)
Components Required:
555 timer IC
2 npn transistors (I used BC547)
Resistors: As mentioned in the video, depending on the voltage of power supply you are using.
Capacitor: 22uF (gives 2.5s of LED on time), 100nF (104)
LED/Buzzer
Breadboard
Power Supply: (5-12)V
Few Breadboard connectors
This channel has a lot more electronics projects & 555 timer projects. So feel free to check them.
-----------------------------------------------------------------------
For more electronics projects, visit: elonics.org/
Like our Facebook page: elonics/
Follow on google plus: plus.google.co...
Your explanation is very detailed and speech clearity is very good.
And why we are connecting that you are telling is important and not in others videos
I faced many problems during this project but they helped to clear my doubts. Very thankful to you for this video 😁
Nice project! It would be nice to have a schematic of the entire circuit sir.
Very awsome circuit and useful circuit! I would use a push on push off latch for the led though.
Nice project! It would be nice to have a schematic of the entire circuit sir. Nice video.
Exactly
It was a really helpful video but can you please provide us with a circuit diagram it would be great.
Superb,,,, this is how it should be taught... Paa G tusi great ho.... Keep up the good work.
awesome explanation my doubt is can we use bistable mode for off and on
Hi sir .I am try project but relay not warking this project any solution
Superb working.... Best video I had ever seen
Kaash ye video pehle mil jata 🙂
Can you make a video on music reactive led using an op amp & rc low & high filter for bass & treble LEDS
hi your mini project is incredible I would like to ask all the names of the component needed
Its very much useful... Nice project.. 👍👍👍
hi @elonics can i please have the schematic of the final circuit, i saw a circuit near the end of the video, but u included more resistors and a capacitor not sure, how this is connected in a schematic.
Great sir nice explanation 👍👍
sir, it worked. how can I connect it to ac supply then to a lighting system?
You need to connect a relay module at the output of 555 timer IC
Your english is good
Allah nazare bad se bachay keep rocking you rokc
my led always shining
Made a inverter circuit ... You are awesome .
Usefull video good explanation
How have you got the values of capacitor and resistor that is shown, can you explain why aren't you using some other values of capacitor and resistor?
thank you so much it worked
thanks for this video really helped me a lot!
Sir can you provide a circuit diagram of this circuit,it would be very helpful
Have you got the circuit diagram???
Bro my bc547 transistor heats up, why is that? I used 9v battery and changer the resistors to 470 because what you said. Please reply asap
Bro how much volts did you use
Very good demonstration but due to your fast talking and your accent it is so difficult to judge the values of the resistors and the worst thing you do not supply a circuit diagram. Really it is a shame as it is a nice project for the youngsters. Many thanks for your kind effort.
Very good project.can you make it like 1st clap on 2nd clap off.
sir can i know which coponents are required to do this i am not undesting what u had provided..
What if i want to keep the LED on until i clap a second time, what should i do then?
What voltage of capacitor should we use?
Bro please upload all your projects circuit diagrams as a video
Hii, i really need schematic diagram on this one. Please help me
Follow the link below the video to his site with schematics.
Izzat Rusyaidi if u find this diagram then send me please?
@@gevinization it doesnt have this one, trust me i also need it
@@anon2447 yeah this schematic is not there
Hi sir, could you pls send mebworking notes of this project
.
Please make a video on reconditioning the lead acid battery
i made in the first part my MIC gets hot & led didnt glow, can you let me know the problem? i have used 470ohm resistor for 9v
Sir can you please provide me the circuit diagram ?
U r amazing!!
1000000000% working
Thank u so much.
BRO NOT WORKING
Can we use a 330 ohm resistor for 9 v power supply?
You can give it a try, but it might heat up a little bit.
Ki
Great!! you can add a relay to control ac appliances.
Yes. That will be of much use for Clap on and Clap off circuits
@@elonics sir can you help me to make day after tomorrow my science fair please help me
Thank you, make more videos please.
Sure, I will
Sir my led still goes on continously, tell me the solution ,i have chnges resistor value up to 1.5k ohms and am using 9V battery kindly give me a solution i want to submit my projecy
Well Explained
Great experiment. ...
Good information
Sir please upload the link forbthe circuit diagram.Am doing this project sir.Please help me out by uploading the circuit
Can we use Mini Breadboard
We have to use 3 trasisters same power?
Very good explanation. I will try this circuit. Thanks.
You're welcome
Please make some video on museum protection system using transistors touch sensor buzzer
Maybe you can use this: ruclips.net/video/yXPxY6-Caz4/видео.html
You'll connect only the probes used for turning on the output.
Why didn't you add C' between pin5 and ground???
can we lock the output like normal 555 circuit?
Very good, I will also make and upload in RUclips. Keep it up !!!!
You will have millions of subscriber soon.
This vedio is become more informative if u provide circuit diagram
Amplifier is very important to circuit or not? Please reply because I don't attached amplifier in circuit
It is necessary
does this work for AC voltage? i have 12V ac
No use I kept on increasing resistance from 470ohm to 100kohm still light glows continuously
after long time video........
This is awesome video. Can I ask that how many volts at the output of the 555 Timer if we use 5V supply voltage?
Thanks; Approximately 5V
If we use 5v relay is it works
Bro please make an video clap to on and clap to off in a single board.
Kowshik Hero read the video's description
you use cd 4017 instead of 555
please help me to connect a potentiometer so that I can adjust the distance of me and the sensor
Do you have a circuit diagram of this circuit??
Can we use a Panasonic speaker
what IC did you use?
Is it necessary to use IC
Nice project, Circuit diagram please
Can we use 1k resistor for 9v
Can u give the link for circuit diagram??
Can we use any npn
very well explained 🔥
bro which mic was used
can you tell if it is possible to use mosfet instead of npn ones here ? If yes then which one?
No, mosfets can't replace the npn ones. Gain can't be controlled using mosfets and the circuit ends up being too sensitive. You can use alternative npn transistors like 2n2222, 2n3904 etc.
Sir I used not gate (IC7404) instead of transistors ..it is working ...but how do I increase the sensitivity?
Great! For improving sensitivity, try increasing the value of series resistor used with the condenser microphone
@@elonics thank you ill try 😊
I've been meaning to make this for my 12th standard CBSE project. Does the given schematic actually work? I don't want to waste time and supplies on a project that doesn't work. Your reply will be really helpful.
@@himanshitomer7502 Yes it works. But I would suggest to understand how it works so that you can tweek the circuit as you want.
can you use a 2n222 transistor
Sir can i ask question?
Can u tell me asap how much voltage did u use in ur project
6V
@@elonics thanks
@@elonics what did u mean by 0v at trigger pin of de ic
how this circuit can differentiate between a clap sound and other sound??
This circuit requires high intensity sound to get triggered. The source of this sound doesn't matter
Is there a possible way to compare the sound into decibel?
Not unless you use an arduino/microcontroller.
If precision is not required, you can try vu meter circuits
Is there a schematic present please ?
can u send the tinkercad of this circuit?
How to increase light glow time
Hello sir isme speaker lagaye
Bro can you send circuit dig of this clap switch
Bro without timer is it possible
how can i use it for 220 v bulb
Circuit diagram?
Can I use the mic from old headphones? Please reply
Yes i think
Please make a video on inverter circuit
Sure. Maybe in a month.
you have to post the schematic?
why no polarity for the capacitor and also for the LED?
It's mentioned in the video
can i use simple normal wires for connecting
Yes
Sir , when i am starting the circuit led remains on
did you solve the problem?
can I uss 28 number copper wire?
Sir,Circuit diagram?
Yeah need circuit diagram
Bisa buatkan untuk lampu Lhe
Can u please send me u r circuit diagram
Can you make that on clap led will on and again clap make led off and can you make to on AC applications with relay
Yes, will make another video for toggling the output and adding a relay