55’ CHEVY TRUCK - How to Install a Mustang 2 IFS From START to FINISH!
HTML-код
- Опубликовано: 28 янв 2023
- 55’ CHEVY TRUCK - How to Install a Mustang 2 IFS From START to FINISH!
Hang out in the shop with me as I FINALLY install our Mustang II IFS (Independent front suspension).
Email: InTheShopTV@gmail.com
Social media:
Facebook-
profile.php?...
Tiktok-
www.tiktok.com/t/ZTRaF5UJA/
Insta-
InTheShopTV
#55chevy #chevy #youtube 
Авто/Мото
Very well explained , good video , good craftsman. Thanks 👍
Thanks for watching! I have lots more videos for the mustang 2 and this build!
Good vid!
Thanks so much for watching!
I know this build is over a year old but I was compelled to share, that as far as the rotor mishap I've read that Corvette spindles along with their bearings are some of thickest beefy upgrades you could make for a performance build.
So, I dont know if I put it in another video, but what happened was, the caliper brackets had 1/8” tabs cast into them. This made the caliper sit 1/8” off, not allowing a 1” rotor. I carefully ground down the 1/8” tabs and the calipers lined up perfectly and accepted the 1” drilled and slotted rotors.
@@intheshoptv Glad to hear it, that is a fine machine you're creating Mike, keep up the excellent work!
@@garylostinspace8500 Thank you sir!
very nice. Im thinking of getting for my 55 as well but i have a 4100 1.5 ton flat bed. not sure if that would fit or not
If you email me (address in vid description), I’ll send you the original frame blueprint. If the frame rails are the same width apart, you can use this or any IFS kit for these trucks. The only thing you will have to do is find center wheel base, which is found by measuring from each leaf spring bolt on the same side, and then marking center.
I just so happen to be making very similar mods to my '57 3100, except I'm using the Full Tilt kit as delivered, and my truck's previous owner had installed a TCI MII front suspension.
On the TCI kit, the same calipers (the Wilwood forged units that you are using) are contacting the caliper brackets prior to the calipers fully seating. Was wondering if you found anything similar?
So if the caliper brackets are at all like mine, they have a little pad on the mounting ears that is just part of the casting. However its meant to leave, or shave down depending upon what rotor width, caliper you use. I had to shave mine. They protrude 1/8” if you leave them, and are flush if you shave them.
Hello ! GREAT video! Did you end up swapping out the old rubber dust boots to the Energy Suspension? What is the part # for upper and lower dust boots, if you don’t mind me asking. I have the same upper and lower and I’m trying to find the part # to order. Thanks for your help
Ha! Great question - one that Im STILL trying to figure out. I looked at the size of every one of their boots in millimeters and NONE of them match the upper or lower control arm ball joints. As soon as I find suitable poly replacements, I will make a video showing which ones I chose and the ridiculous effort it’s taking to find them!
@@intheshoptv I’m having the same challenges!! I called them up, email them pics with measurements and still no one can help. Crazy !
@@flyaz11 You’d THINK this stuff would be widely available 🙄
@Poco Loco Here’s the link to the spacers www.speedwaymotors.com/Mustang-II-Rack-Spacer-3-4-Inch,37559.html
I installed a mustang ll cross member and for some reason the left end tie rod does not reach. Even with a 2" spacer.
@@adamvalenzuela6626 measure your tie rods and see if they are different lengths and possibly installed on the wrong sides. The instructions were wrong in my kit, I only needed one spacer, not two. Also, if you find you still need a different length, call them, and they’ll swap it out. None of these kits are ever exact in my experience… wait till you see my 4 link kit video and what I had to do🙄
Why didn't your kit come with the c-notch pieces?
It “technically” clears the tie rod ends, but depending upon how low you adjust things, you may or may not need them.
Wh not swap your axles to 5x4.75 to match the rotors you want?
I have them already but I was thinking of getting them drilled.
awesome build my dude. what bolt pattern are you going with?
Thanks! A ford 5 x 4.5. But I maybe have to re drill my rear axles to a chevy pattern for wheel availability reasons. Check it out: 55' Chevy Truck is FINALLY a Roller... Now What?
ruclips.net/video/JWozLZcG37U/видео.html
I seen front rotors Chevrolet pattern for the mustang 2 front end@@intheshoptv
@@MrBigal123123 yes they do make them. But my rear axles are from a Ford Explorer so I decided to stick with the Ford pattern all around… unfortunately, the matching wheels I need are only available in a Chevy pattern so I will most likely have to drill the axle flanges. No biggie
You should have put grease in the roter
The rotors and bearings are packed with grease
Where did you get the brass bushing for the spacers the steering ?
Speedway included them in the M2 kit, but they can be purchased separately if you need:
www.speedwaymotors.com/Mustang-II-Rack-Spacer-3-4-Inch,37559.html?CSEGoogle&CSE&CSEGOOGLE&gclid=Cj0KCQiA8t2eBhDeARIsAAVEga0RLNZoMeF2zmTlTqMsQm6SvP20eNYGNHlKCZtBN7Dw0OIiRUbDGPAaAhCaEALw_wcB
I’m in the same problem with the tie rods extension did you get them from their speed way motor as well
Is their a way I can contact you I’m running in to some problems my self
@@carmo1695 yep! If you have the power rack, here is the link. If you have the manual rack, they have a less expensive extender kit
www.speedwaymotors.com/Mustang-II-and-T-Bird-Rack-and-Pinion-Inner-Tie-Rod-Extensions,7488.html?sku=91034345-POW&CSEGoogle&CSE&CSEGOOGLE&gclid=Cj0KCQiA8t2eBhDeARIsAAVEga1Wpn1eeFc7eqqlg7onrduY0cuuznEz0BoM5PKdsgx6-Q2LMcQlOVkaAh2OEALw_wcB
@@carmo1695 Absolutely! My email is in the video description