Scanning & Processing in Hand Scan Mode | Creality CR Scan Lizard User Guide

📢 🏷️ Looking for a discount on 3D printers, 3D scanners, laser cutters, and more? Check out my Creality affiliate deals page!
shareasale.com...
10% off Raptor 3D Scanner with the code "RAPTOR10"
10% off Otter 3D Scanner with the code "OTTER10"
Get 8% off most printers AU store with the code "AU8"
Get 5% off site wide UK store with the code "UK5"
Boost Your Business's Online Reputation with Climbo!
Looking to improve your online reviews and attract more customers? Climbo's all-in-one review management software makes it easy to gather, monitor, and manage reviews across over 85 platforms, including Google, Facebook, and TripAdvisor. Plus, you can get 50% off with the coupon code DRAFTID50
👉 Try Climbo now and see the difference!
www.climbo.com...
☕ Buy Me a Coffee ☕
This all takes a lot of time, energy, and money, so If you want to throw a few bucks and provide monetary support for what I do, you can buy me a coffee at the link below. Just $5 provides a huge boost of confidence (and caffeine) and keeps me going. I am forever grateful. If you don't want to support with money, that's totally fine, and you can always just subscribe to the channel and like the video instead.
buymeacoffee.c...
🎤 Connect with Me 🎤
Instagram: / draftid_au
Facebook: / draftidau
Discord: / discord
✏️📐 More Resources ✏️📐
Check out my SolidWorks Beginners Course [bit.ly/2GNqkgb] and the Creality CR-Scan Lizard Guide [ruclips.net/user/pl...

[@toxic3dpd183]

Finally a tutorial that doesn't skip steps going to give this a try!

[@DraftID]

Thanks for the comment and glad you found my vids :)

[@jannerboyjohn]

Thanks again for all the effort with the videos and this one yet again excellent. I was unaware how to "save" the bottom section of the scan which is picked up when selecting and deleting the bottom plane. One thing I learned just yesterday is that if using the black cloth bag, as supplied with the kit, under the object on the table it doesn't pick it up so no bottom layer to remove! I also used a lazy Susan, as it was a bigger area, and hand scanned with the same black cloth bag underneath and it produced excellent results, just by rotating the table slowly by hand. Have a good Xmas.

[@DraftID]

Haha yup I accidentally figured this out while filming about adding a black surface to the table as it won't detect and therefore nothing to really clean up before processing. I'll definitely have to do a quick tip video on this!

[@TheRealDuBTeK]

A+ on the content here, this helped answer some questions I was having on cleanup efforts prior to aligning or processing

[@DraftID]

Thank you, glad it helped :)

[@fingerofdoom2007]

Excellent tutorial!

[@DraftID]

Glad you liked it!

[@MrWagner528]

excellent, thank you.

[@alexlux147]

As always you made an excellent tutorial, i really like them.
I have two suggestions, the first with the aligned, most of the time automatic alignment worked well for half the model, because of the reference scan. You could auto aligned all, manually aligned only one failed to the reference scan and then use it as a new reference to auto aligned only the failed scan, hiding the correct. In that way you will save time and effort.
The second refer to delating the ground. The selection plane always select some part of the model, instead of trying to follow the contours of the model, you could rotate the model horizontally, use the lazo selection, start select from the rightmost part and end to the left. The lazo will automatically join the two ends with an horizontal line.
hope i was helpful and clear to you and the community.

[@DraftID]

Thanks! Ill play around with those suggestions.

[@whoopiegolberg9015]

I use hand scanning with the turntable most of the time too, i've found slapping some black duct tape on the top makes it even better.

[@DraftID]

This is something I have discovered too while filming this video and I want to do a video as a quick tip about it. But basically the fact that it does not handle blacks well can be used to your advantage as you can put something black under the object which it won't detect meaning you don't have to bother with deleting unwanted table geometry.

[@3DPRINTINGWITHLEE]

Wonderful info that helps a lot

[@garagecedric]

Good video, I really hope the auto align improves, that would transform the scanning process and make it more usable.

[@alexfedorenko3785]

Thanks man! Great demo!

[@DraftID]

your welcome

[@Edward3DFX]

epic video !

[@DraftID]

Thanks you!