Repairing LED back-light using SMD and DIP led - Samsung 32"
HTML-код
- Опубликовано: 26 фев 2017
- replacing the smd by dip led caused a sort of dark spot that can be seen only during high brightness scenes and clear white screen, i can live with that.
Time Passing By by Audionautix is licensed under a Creative Commons Attribution license (creativecommons.org/licenses/...)
Artist: audionautix.com/ 
Хобби
Ingenious. I learned a few things about samsung LED backlighting here. Thanks for sharing.
Thank you so much for sharing with us. I've fixed my Samsung TV by myself! Peace! \/
Thank you sir! Saved me a whole lotta money!
repairing led back linght you do good job
Wow, your burnt the sh*t out of the board, but the white-out did wonders...good job!
mate you’re awesome !👏👏👏👏
thank you for the tip of using the back of the strip on a soldering iron because I had been trying to use my headgun and no matter what it was a mess, and or using the soldering iron on the pos or neg side until it heated up enough that it would crack off and then do same for other side for it to slide away then clean up the contact points , yours seems much easier aha though it leaves a nasty balck mess aha
Thank you very much for this video, I have a new TV again
Well done!!!
nice technique I'm learning with you TV repair
ha ha ha
Useful video thank you very much
Good work bro. Weldone
is it ok to clean the protective layer one by one? tnx
2 pcs of standard LEDs (3.3V/0.04A) instead 1W LED (3.3V/0.3A) = excellent. How many seconds it worked?
Buy complete set of LED strips at Ebay or ali (about 25-30$ for all set) - it is only correct solution.
There was a much better way to fix this witout exposing the LED lamp to excessive he. Using a jumper LED strip about 2inches long. You can use can scrape the coating on the strip on each sie and sold a bare wire to each side. The strip gets the heat, not the LED. It's a good piggy way to do it and it works.
Thx a lot! It's very useful!
ا م مين ف ك
Interesting is the way you lift the Backside away from the LCD ! Everybody else uses those suction-clamps to lift the LCD off of the back!
Hi what will happen if i remove all my lcd tubes and place leds which is powered from outside source ? Please reply
how many volts am i required to right up with individual bulb sir?
Very nice brother
Did you put those 2 leds in series together ?
Sir aap ne ek wayar se kisme sort kiye hai jo pori led jal rahi tha
The dip replacement leds always need the diffuser lens otherwise they will appear as white spots on the picture.Also you can remove the bad led and solder with wires a small part of led strip with a single led taken from old one.In some cases i have replaced the burnt led with a resistor as a dummy load.There was a very little dark area hard to notice.
George George your are right
Good morning friend, I have a television that has the same fault, uncover it and I could see that I had a led burned in the bottom line, my question and my problems is the following, when replacing the burned led all turn on individually, I can do so that all the led on the bottom line turn all on
Rodolfo Pirela replace the hall strip
So nice no1........
Sunny Shiralkar parallel, they also failed but failed shorted
You did ut backwards u should've unplug the t-con and tge driver board first before the bezel
Good job
They sell these compatible led strip bulbs. Just copy and paste-- 2 Pack x Led Strips 3v Bulbs Diodes 32-65 inch Tv Optical Concave Lens Fliter Backlight w/ cable Double-side Tape 10pcs/pack ( aliexpress ). No need trial and error. No need to live with that dark spot, sir.
What is use checking tool sir marketing how much rate
Where do you get your tools
So I took my Samsung 60 JS 7000 apart. It has ten rows but only bottom 6 work and the top 4 rows don’t. I switched out a working one and placed on top and the bad one at bottom. All rows lit up like a Christmas tree. I was happy only to find out that when I picked my tv to check the back the TVs top4 rows turned off again. I kinda wiggled it and they turned on again. The strips all work fine. Do you know what could be causing top 4 rows from turning off? I have no issue with the bottom 6 rows. If you can help or anyone that might has some knowledge of tv electronics it would be greatly appreciated. When this first started I would just give a bang and tv would work fine until it didn’t. Eventually not a bang to tv would work. So my thinking there is a loose wire or something might be triggering or not triggering for the lights to turn. Again any help would be great.
Light Glass Joining Paste Name please Answer me
Super boss
Good work boro
Changing 1by 1led bulb is good for up to 2months. Next time change all with new backlight so the costumer became satisfy
Boss pwede pa home service ung LG bale ung screen nya may dot dot na ilaw po.
@@michaelanthonygarcia814 location mo bro?
Tiga canlubang laguna po ako saan ba po location nyo?
Sir Samsung led TV 42 back light single 1 strip ok but 6 strip not ok sir pls help
thanks
my sony bravia LED mai kabhi kabhi light automatic bandh ho jati hai... pls give solution
Thanks sir
Hello bro how many days that dip led worked ? Plz reply. And why you used 2 dip led in parallel instead of useing it in series to maintain 3v
Sir LED bulb ko multimeter Se Kaise Pata Kare Ki wo kitne volt ka hai
I dont know what i missed. Im repairing my smart tv by my self. The problem is the light reflector and my tv have white spot. After repairing and i switch on the tv, i found out the lcd broken. I dont know where i miss. Im thinking what causing the broken
Did you put or plug back everything in place and order? And make sure you didn't rip off any parts. A better description of your Problem would help to fix it.
Pretty clever but I wonder how it would look if you did all of them like that. I'm sure 1 wouldn't be noticeable at all I'm sure. Probably wouldn't notice it much if you didn't even put the 2 bulbs in there but if you could replace them all that would be amazing if it worked. I have same problem with leds but not sure how many. I know I have to order the led strip but takes so long to get here but I do have some of those so I might just try this out. It's gotta be better then the other solution using a regular diode with a resistor to bypass the led. Either way ingenious idea and now I might be able to get mine working instead of waiting.
my2centz veery ugly indeed, buy a new strip don't waste your time
@@doityourself8314 I ended up waiting on the smd chips and replaced them using a heat gun even though you say it will reduce the life I figured it's so easy and the chips are so cheap. I just wanted to basically see if I could fix it myself. It's been working fine so far although I wish I knew of a glue that would hold the stupid reflectors on other then 2 part epoxy which is what I ended up having to use after taking apart a couple times to reinstall them lol. Superglue isn't so super lol. I don't know why but I tried 5 different name brand super glues and none would work. It's like the lensons kept them from drying or something. Very aggravating lol.
Use clear bathroom silicone sealant. Just a small dab on the end of a needle for each spot then let it set for a few hours before moving. It will hold.
airkencing others?
bro 21 inch 10 data tp.vst59.p63 firmware send me
I tried same thing when I could not source the correct SMD LEDs, unknown voltage and amps. Mine glowed very dim. My Sharp had 3 diffusers: 1 fesnel lens, 1 opaque and one semi clear along with the LCD glass.
sir mera led32 inch asembal tv hai displya nahi araha aha, i saund ata ahai kitna kharcha ayaga please reply
meu migo não se troca leds fazendo este torrão na placa não viuuu, use um soprador térmico ou uma estação de ar quente tirando pela parte de baixo, que você não vai deixar nem vestigio de que o led foi tocado, use uma fita térmica na parte de baixo a onde você vai aquecer para retirar o led, não vai escurecer e vai proteger a régua ok,
fica a dica.
I will try to fix mine. I also think its the back light problem too.
Street lait babu speir pati yakkada dorukuthai chepandi
I watched the video carefully I followed what you did but I made a mistake I forgot the order where the panels are placed behind the screen.samsung tv ua50au9600 Can someone help me !!!
Vu 32inches TV light problem. If I want to fix . How much voltage light I need to buy?. Pls reply or give backlight buying link.
Just regular leds will work just fine
@@thenegotiator9701 any buying link ?
Geno christoper my advice :buy complete light strip, search by numbers on your one
how much volte required test led
what is the average cost of one LED strip
Y a qué hora Quito y puso las placas reflectoras y difusoras y difuminadoras para los que crean que es muy facil. No lo es, solamente con práctica lo pueden hacer, de lo contrario pueden romper el panel de LCD. Y más si son de 42p, 50p o más
Bayya Videocon led tv 50 inches speakers cost plz
thank you good job
Bohat kamal
Nice fix i'm in process of replacing some LED's on an LG 49" just waiting on new LED's and also tester
ربنا#🔗💖
Hi, how do you fix the little plastic dome on top of the LED? Do you use glue?
Julien super glue
Where to buy led strip
Try and do a 65in TV
Bro my Tv 55" Samsung Tv half picture is clear visual and the bottom is dull display , wat solution can b done , I checked with the technical guy he said can't replace bottom strips alone , need to change completely, he said for 50" itself they charged Rs.8000 , don't know how much for my 55" , Rs.10000 , does this cost this much or any other solution , plz help brother 🤝
السلام عليكم انا في عندي شاشة جي جارد سمارت ٤ك ٥٥ انش الجهاز قبل شهر اصبح ينطفي بشكل كامل و بدون سبب وعند اعادة تشغيله وذلك بفصل التيار كاملا ثم اعادته يشتغل بشكل طبيعي لبعض الوقت واخيرا لم يعد يشتغل .
شو ممكن يكون السبب وكيف اعيد تصليحه اصحاب الخبرة الرجاء الارشاد ولكم جزيل الشكر.
Bhai mera led tv ka roshni apne aap kam hoke kala andhera sa jata hai.. Kabhi kabhi kuch ghante ya 1din keliye aaram se chalta hai.. kuch dino se ho raha hai yeh problem.. please help me bhai.. kaise khud hi ghar pe thik kare boliye toh..
Do you need LCD TV backlight belt?Our manufacturer can provide you with a large number of products.
Damn that looks like a hot mess. But I guess if it works and no one will see it.....
Where can I get these LED strips to buy?
Same doubt...and about size and volt
Gujarati galli hyderabad
Ray Zaps search by the numbers on your one
Anyone watching the last part he needs to learn to solder and use flux, pair of tweezers and buy a smaller soldering iron flux cleans the board and helps the solder to stick without it you get a mess
Hallo ich habe eine Frage die zum Teil ihr Video betrifft. Und zwar habe ich einen Grundig 55 VLE 9474 der nach ein Paar Minuten oben und unten dunkel wird. Ich habe auch bemerkt das er dunkel wird sobald die Hintergrundbeleuchtung ständig die bildschatten bearbeiten muss das dann dass Bild oben und unten dunkel wird. Wenn ich denn Fernseher direkt nach dem einschalten als pc HDMI Monitor benutze bleibt das Bild stabil aber sobald viel farbwechsel im Bild vor kommt dunkelt er wieder ein. Könten Sie mir vielleicht bei dem Problem weiterhelfen? Ich Frage Sie da ich mit ihr Video anschaute und herausnahm das die Ahnung von der Materie haben.
Und wenn nicht trotzdem Danke!
Kje dobiti led diode za " Black lite"
كلامهم✖✔✅®
sorry but its not a profesional , how big deal is replace one SMD ?? i did replace 27 each and now its no different like new one tv :):):):)
हमें अपनी एलसीडी रिपेयर करवानी है कि रुपए लग जाएंगे आवाज आती है डिस्प्ले नहीं आती
what ever you put on the led to glue it killed the led
Joseph Melville they also failed but failed shorted
كان عندي نفس المشكل إصلحته ولكن بعد أسبوعين رجعت نفس المشكل نصيحة لاخواني اذا فسد استر آخر ودعك من البريكولاج
nota 2
It is my belief that it is a waste of time to replace or fix the individual LED's; especially if the LED's have been burning for years. Better to purchase the LED strips and replace the whole lot. These are relative inexpensive on eBay. And VERY easy to replace all of the entire strips.
aur sath main horisantal line hain
No wonder you said they fail quickly after being heated... Don't ever go near a soldering iron again...
Thats not going to work because its gots to be flat
flash file send me 21 inch
i give up. i will buy new one if this is so troublesome.
BAD TOOLS USE
acheni uongo haiwezi ungua red moja simple namnahiyo
aja si tengo buena todas las led y su voltaje y no da imagen que es lo que se jodio entonces
replacing all leds strips would be better choice that way you know they are all new and you wont have to this repair again
please put subtitles in Spanish, so we can understand, that way you will have more subscribers on your page, thanks greetings from argentina🙋♂️
The led is wary low quality
الترقيع لايستمر
Pa home service po ako sana
This guy talks too much
Nun Ya 4v
I NEVER change the leds i always jump them
Can u help me in private please man
As a rookie I just purchased all new back light strips. Don't wanna risk another one going out again.
How did that work for you? I'm in the same process and ordered a new set of back light strips from China.
@@alexboyraz8257 yea got my leads too from China with high ratings. I already installed them and all I can say is that it was no easy task BUT I enjoy a challenge. Just be very careful on the removal of the lcd. Other than that the TV works great 😁👍
sir Aapka number dijiy
the watts of the original smd led is bigger that of a dip led, of two of then ,as its curret too, your repair is not profesional
La réparation 😂
Led diganti yg rusak aja dua hari mati lagi, harusnya di ganti semua.
какая то колхозная работа(((
This is not a skilled worker ! _Special Barbarian !_ :-(
DIY = do it yourself, we don't need one that's the point
@@eyeswideshut2800 Amateur? Original 500 mW LED!
Are you loading a weak LED100 mW?
@@sziamiau1 Nope but I just watched a video on how to with success so may come in handy. I'm from Texas and have built many properties so save the advice, we build stuff here OURSELVES....ijs