Это видео недоступно.
Сожалеем об этом.
How test and repair VW / Audi 2.0T 1.8T PCV valve with an RKX upgraded PCV valve
HTML-код
- Опубликовано: 5 дек 2022
- You can find our upgraded PCV valve here: www.rkxtech.co...
Testing for a ruptured PCV valve is simple! If you feel vacuum coming out of the top vent hole on the PCV valve cap your PCV valve has an issue. This vent hole is simply a breather to let the PCV valve move up and down freely. You will never feel / hear vacuum from it when it is working properly.
Excellent demo! I’ve watched a dozen videos on this topic, and you’re the only one… to show how to perform the finger vacuum test. Cheers!
This video needs an ASMR tag. I feel like I'm hearing the rubber gloves, the clicks, and everything way more than any other car vid. Must have a solid mic setup!
Thank u for showing how to perform vacuum finger test. Simple video with easy diy repair.
this is the only video I have seen that shows this
Magnifico
Perfect visual with comments
And great volume/ sound.
Great product, a 10 minites repair job if you have the rigth machinists scribes or a few small flat screws driver.
Removing this cap is the biggest pain in my ass rn
Hi, if I have 86mbar in the system with a new PCV valve can I replace the spring with more tension to achieve at least around 100mbar? I know one service which calibrates these springs.
Will a PCV diaphragm from a MKVI GTI work? They look the same. I ask because I have a spare laying around from when I used to own a GTI
How much vacuum is normally present in the crankcase at idle in these turbo engines? Is it enough to cause the engine to misfire and nearly quit when the oil cap is removed? When the diaphragm tears, does the vacuum pump normally apply full vacuum to the crankcase, unregulated by the PCV diaphragm?
There is a good amount of vacuum inside the crankcase when this is working normally. These engines are sealed tight so removing your oil cap with the engine on will cause a missive vacuum leak essentially. When the PCV valve ruptures even more vacuum is applied to the crankcase and its typically really really difficult to remove the oil cap with the engine running because there is so much vacuum.
I have some oil leak around this diaphragm round cap you pop off. Should i check it or its not a problem?
Same deal on the b5.5 2.8l V6?
HOW DO YOU MAKE IT LOOK SO EASY WTF I'M BREAKING MY OEM CAP TO TRY TO REMOVE AND ITS IMPOSSIBLE
Exactly lol he made it look so easy while im struggling to pop it off. Any tips?
Hello where can I find just the new diagram / rubber seal and cap that you showed in the packet and is that universal or model specific ? I have a 2009
Audi rs6 5.0l suffering from this issue ?
AutoZone has the diaphragm, most places sell the whole assembly
@@TheAngeloMichael great but I couldn’t find it on their website
@@TheAngeloMichael I see but I couldn’t find it on their website
I have p0171 code system to lean
Do yall sell one to fit a 2021 VW Atlas 2.0T?
I got 2.0t and mine doesn’t have clips or the hole opening. It’s all just one sealed piece
i think its aftermarket u should replace oem part*
How the heck that hole opening there . Bc pressure ?
Yes
The pressure from blow by through the small gap in the piston rings will cause this to perk up when pressure exceeds a certain level
@@mrw1160 turbo engines requires that 6 k miles oil change . I do 6 k high quality oil. And also best to replace oil seperator at 80k miles
air blowing out of the breather hole is normal?
I have the same. Blowing instead vacuum
Will this trigger a P0172 system reach code. Mk6 gti
No cause the fuel is to fat then