Hey Manny, I have the swiftXL with the new 10inch screen. How do I change the parameters on this machine because it doesn’t seem to be the same way as this machine.
Hey there. The hooping was done off-camera but we are pretty sure that Manny did use a stabilizer. If he didn't is because the cap was a very tough structured cap and didn't need it.
From my understanding, the cap driver can embroider 270 degrees around. What is the maximum width in inches for digitizing? What is the maximum number of the x-axis settings on the machine? What if I have an image that I would like to embroider on the front of the cap and another image on the side of the cap by using only one digitized image so that I don't have to keep stopping and changing .dst files?
Hi Ricardo, the maximum width is 12 inches for digitizing and the maximum width of the x-axis on the machine is 320º. Yes, you can setup multiple designs on your digitizing software in one file. You can set up a template in your digitizing software with the maximum dimensions of the cap embroidery area, which is 12" wide and the height depends on the type of cap that you want to embroider (typically it ranges from 2.2" to 3"). Once you set up your template just place your main design in the center for the front of the cap and then place your other design on the left or right side depending on which side you would like to have it embroider on the cap. Make sure to run a test to make sure you get the spacing just right. I hope this helps, let us know if this helps :) Also, we have a facebook group with a community of experienced embroiderers that post their work and help answer each other's questions. If you would like to join you can check it out here: facebook.com/groups/embroiderymastery/
so basically you can't make the machine move automaticaly to the side with the digitizing software? also I don't like when I want to optimize trace a design on caps but first of all I have to trace it normally.
Im totally new to this but can this be done by hand and if so will it be as good as this and how long would it take if the design is kinda more detailed?
Hi there! Thanks for watching. Hand embroidery is possible on caps, but it will take a lot longer, especially if the design is more detailed. Machine embroidery can be completed in minutes, on the other hand. There is also more of a learning curve associated with hand embroidery, especially since it's an artistic ability, whereas with machine embroidery the machine does the work for you and you get a clean, professional finish. Hand embroidery stitches tend to be larger and less "tight" than machine embroidery stitches so creating detail is harder.
@@ricomatv thanks for the reply i don't have the money for a machine which i think the good 1s are like 300- 1k let alone the space to store it but i wanna try making my own patches for my hats and jackets as the patches i buy cost 20 n up for large and detailed pics im pretty good at drawing was thinking of like doing a large back patch of snoopy which imo would be a easy as its a pretty simple design to make for a beginner
Hi, how I can embroider on my ricoma TC using cap driver, design larger than 2" ??? I have seen a lot of custom caps embroidered with monograms in size about 3 or 3.5 inches? My machine doesn't allowe me to go more then 2"
If you go to "Emb Param", then "Frame", and change the Y size on caps to "75" that's roughly 3 inches, but we do not recommend maxing out. Try to keep it under 2.75 inches max for best quality.
Hi there, thanks so much for watching. This is a great question to ask in our Facebook support group, Embroidery and Custom Apparel Mastery. This group is meant for all lovers of embroidery with lots of resources and more members discussing topics and helping each other out and learning about Ricoma machines and other brands! We recommend you join this group as we'd love to have you! facebook.com/groups/embroiderymastery
hola, tengo una duda con respecto al ancho de bordado de un diseño, ojala me puedas ayudar, te comento, haber si me explico. tengo una letra que tiene un ancho de 15mm le he quitado la opcion de division en las propiedades de la puntada satinada, pero cuando llega a bordar a esa area, la maquina se para continuamente marcando un error, le vuelvo a dar comenzar para que continúe bordando pero se vuelve a parar con error, no se si sea porque el ancho de la letra en sus columnas sea mayor a los 12mm recomendado . Espero haberme explicado bien. gracias
Hi. If you have a Ricoma machine please contact tech support department for assistance. They will help you resolve your issue. www.ricoma.us/tech-support
![ARGENTINA vs. PERÚ [1-0] | RESUMEN | ELIMINATORIAS SUDAMERICANAS | FECHA 12](http://i.ytimg.com/vi/xtI25ENDDSY/mqdefault.jpg)
Hey Manny, I have the swiftXL with the new 10inch screen. How do I change the parameters on this machine because it doesn’t seem to be the same way as this machine.
SETTINGS/EMB PARAMETERS
I was actually wanting to see how you set up the cap
Hi! Are you referring to the hooping portion?
Can u make a video how to do lettering with a regular hoop on side of a hat?
That's a great idea, thanks for your recommendation!
Can a Ricoma MT1501 embroider baseball gloves and mitts?
Hi there! Absolutely.
Did you use backing paper for this?
Hey there. The hooping was done off-camera but we are pretty sure that Manny did use a stabilizer. If he didn't is because the cap was a very tough structured cap and didn't need it.
Hello I would like to know which are the frame in size x size y offset x offset x y and corner r to embroder a cap thank you very much !
Hi, the parameters are different depending on the size/type of cap. Estimated measurements are Y to 85, and X to 300-400. Remember to always trace!
Your videos are excellent
Glad you like them! Thanks for watching (:
Hello do you have a video on how to embroider the left or right panel of a hat off center not the sides?
I have the same question
Hi! We found this video from a tutorial we did, hopefully it helps.
ruclips.net/video/hCjEfRBHsUI/видео.html
From my understanding, the cap driver can embroider 270 degrees around. What is the maximum width in inches for digitizing? What is the maximum number of the x-axis settings on the machine?
What if I have an image that I would like to embroider on the front of the cap and another image on the side of the cap by using only one digitized image so that I don't have to keep stopping and changing .dst files?
Hi Ricardo, the maximum width is 12 inches for digitizing and the maximum width of the x-axis on the machine is 320º.
Yes, you can setup multiple designs on your digitizing software in one file. You can set up a template in your digitizing software with the maximum dimensions of the cap embroidery area, which is 12" wide and the height depends on the type of cap that you want to embroider (typically it ranges from 2.2" to 3").
Once you set up your template just place your main design in the center for the front of the cap and then place your other design on the left or right side depending on which side you would like to have it embroider on the cap.
Make sure to run a test to make sure you get the spacing just right.
I hope this helps, let us know if this helps :)
Also, we have a facebook group with a community of experienced embroiderers that post their work and help answer each other's questions. If you would like to join you can check it out here: facebook.com/groups/embroiderymastery/
so basically you can't make the machine move automaticaly to the side with the digitizing software? also I don't like when I want to optimize trace a design on caps but first of all I have to trace it normally.
Hi there, we recommend reaching out to our customer service team so they can try to provide you with suggestions/alternatives. --->service@ricoma.com
did you use stabilizer?
Hi! For this specific cap we didn't use a stabilizer.
hallo please show how to hoop correctly for the sides please
Hi, please check out these videos that can help you --->ruclips.net/user/results?search_query=hooping+side+caps+ricoma+
What size would you recommend for a five letter name I can’t figured it out in millimeters height and weight please help
Hi there, our techs will be able to help you with that! ricoma.com/us/tech-support
Im totally new to this but can this be done by hand and if so will it be as good as this and how long would it take if the design is kinda more detailed?
Hi there! Thanks for watching.
Hand embroidery is possible on caps, but it will take a lot longer, especially if the design is more detailed. Machine embroidery can be completed in minutes, on the other hand. There is also more of a learning curve associated with hand embroidery, especially since it's an artistic ability, whereas with machine embroidery the machine does the work for you and you get a clean, professional finish. Hand embroidery stitches tend to be larger and less "tight" than machine embroidery stitches so creating detail is harder.
Hope that helps! Let me know if any other questions. Check out my latest videos for more on machine embroidery!
-Laura
@@ricomatv thanks for the reply i don't have the money for a machine which i think the good 1s are like 300- 1k let alone the space to store it but i wanna try making my own patches for my hats and jackets as the patches i buy cost 20 n up for large and detailed pics im pretty good at drawing was thinking of like doing a large back patch of snoopy which imo would be a easy as its a pretty simple design to make for a beginner
Do y’all have a hoop to embroider on sleeves?
HI there, we highly suggest using the 8-in-1 device for embroidering sleeves. You can check it out here: shop.ricoma.com/products/8-in-1-device
will that be the same for a tc1500
Yes, same process!
How do I ensure the cap is set correctly? I seem to be outside the trace line
Hi! We did a tutorial on how to do this, check it out --->ruclips.net/video/eIqpTe5usHA/видео.html.
Can I embroider Center of hat and side of hat at the same time ?
Hello. No. You will have to do the front and sides separately.
Hi, how I can embroider on my ricoma TC using cap driver, design larger than 2" ??? I have seen a lot of custom caps embroidered with monograms in size about 3 or 3.5 inches? My machine doesn't allowe me to go more then 2"
If you go to "Emb Param", then "Frame", and change the Y size on caps to "75" that's roughly 3 inches,
but we do not recommend maxing out. Try to keep it under 2.75 inches max for best quality.
I’m so high I thought this was a joke about not having a Ricoma TC machine thing lol
How do you do it to for the Melco bravo
Hi there, thanks so much for watching. This is a great question to ask in our Facebook support group, Embroidery and Custom Apparel Mastery. This group is meant for all lovers of embroidery with lots of resources and more members discussing topics and helping each other out and learning about Ricoma machines and other brands! We recommend you join this group as we'd love to have you! facebook.com/groups/embroiderymastery
Is this method possible on the TC machine also?
Yes it is.
Can you extend the y axis as well?
Yes!
Amazing
Thanks!
great video! thank you.
Thanks for watching :)
How do I embroidery on the side with the em 1010?
HI there, you can follow along with this video using your EM-1010. Just be sure to adjust your parameters and trace your design before embroidering.
hola, tengo una duda con respecto al ancho de bordado de un diseño, ojala me puedas ayudar, te comento, haber si me explico. tengo una letra que tiene un ancho de 15mm le he quitado la opcion de division en las propiedades de la puntada satinada, pero cuando llega a bordar a esa area, la maquina se para continuamente marcando un error, le vuelvo a dar comenzar para que continúe bordando pero se vuelve a parar con error, no se si sea porque el ancho de la letra en sus columnas sea mayor a los 12mm recomendado . Espero haberme explicado bien. gracias
Hola Alfonso, por favor llene el formulario en esta página con más detalles para poder ayudarle:
www.ricoma.us/tech-support/es
Hello, good afternoon I am from Argentina, I have a Ricoma EM-1010, my question is, if those parameters are compatible with my machine. thank you
can you do this on the EM-1010?
Yes! You can embroider the side of hats on your em-1010!
Is this method possible on the EM1010?
Yes it is.
@@ricomatv please explain how EM 1010 don't go past 200%
how much can you extend the y axis?
Hi! for help with this, we suggest calling tech support -> ricoma.com/US/tech-support
Subscribed
Thanks for watching!
How can I fix a cutter error 257 help!!!
Hi. If you have a Ricoma machine please contact tech support department for assistance. They will help you resolve your issue. www.ricoma.us/tech-support
flawless
Thanks! :) We have many other great videos planned going forward. Is there any topic in particular that you would like to see us cover?
Aga videos en espanol tanbien gracias
¡Gracias por los comentarios! Esperamos hacer esto en el futuro.
How many times can you use the word “actually “??? Way too many!
Roy Are You American?
Sometimes silence says more.
"Actually"
7 8 loo l loo
You seem Afghan
Is this for the Em1010 machine also?
yes!
Thank you