Thanks my chain was making a crunching sound, so I lubed the chain & made it worse, Lucky enough I spotted it was way to loose!! Thank god for videos like this.. cheers
Had to buy a new chain & a new sprocket didn’t realise how expensive it was for another chain, but running like a dream once again!! Thanks for the advice..
There are quite a few sub-optimal things about this video. First, the chain is likely in need of replacement. When he moves the wheel you can see on the top side of the chain that the links are not aligning themselves properly. Second, a torque wrench should be used for two different reasons. The first reason is that anyone watching a video like this may be a novice, and they should not be encouraged not to torque the axle nut to the manufacturer's specification. The second reason is that V-Strom swingarms have a history of developing cracks near the axle, and excessive torque may be a factor there. Third, most folks who use the chain to keep the axle up against the adjusters while it is torqued use a soft rag or towel in between the chain and sprockets, rather than a hard tool. Also, someone suggested this guy might be from the western United States. I doubt it. He specified the chain slack in centimeters, and the accent isn't quite right.
I think in the manual it says to check the slack with the bike on the side stand. Where it would be smaller than the central stand. Also it says it's between 2 and 3 cm.
True! This is because manufactures often dont supply the bikes with centrestands. So they cant put that in their manuals. You can do it both ways :) basically the same
yes; mine doesn't have it :( but mind you it's not the same; because chain tension changes with the swing arm's travel; i guess the risk is to bottom up your back shock but not on the shock but on the chain not being able to give in more;
I'd rather have it on the loose side, 3-4cm, long travel suspension on the vstrom, if you are heavy or 2 up fully loaded I wouldn't like the chain to be too tight, puts too much stress on the output shaft.
IIRC the bike should be on the side stand when you measure the slack, otherwise the chain might end up too tight, which is worse than too loose. And if you have a torque wrench handy you should check the axle nut torque -- 100 N-m.
Peter Beens thanks for the comment! I find it easier to do it on the centre stand. I take in account to leave a little slack extra. but like all the bike maintenance. keep a close eye on your owner manual or service manual ;)
I think what Peter is saying is that with weight on the rear wheel you can see the true chain slack but if you use a center stand it may stretch a little more after you put weight on the rear wheel
regardless of bike the the swing arm should be in line with the rear axle & the swing arm pivot point and the drive sprocket centre shaft (that is normally hidden under a cover.) if you do it any other way you will over tighten the chain !
judging by how much you had to pull the wheel back, that chain needs to be replaced. But since this video is almost 3 years old, I am pretty sure that chain is gone by now :)
great effort sir but... ...chains on DL650's are adjusted on side stand, not centre stand. The measurement will be incorrect using the centre stand and be too tight. ...a chain that is is too loose is better than a chain that is too tight, obviously correct tension is better all round. NB sorry I see this has been mention before
Thanks my chain was making a crunching sound, so I lubed the chain & made it worse, Lucky enough I spotted it was way to loose!! Thank god for videos like this.. cheers
Had to buy a new chain & a new sprocket didn’t realise how expensive it was for another chain, but running like a dream once again!! Thanks for the advice..
“i’ve checked everything, to make sure everything is ok” screwdriver still hanging out of the rear sprocket.
Lool for cosmetic effect
Exactly ..what a guy
Ready let's goo
That’s just incase he needs it later ..
There are quite a few sub-optimal things about this video.
First, the chain is likely in need of replacement. When he moves the wheel you can see on the top side of the chain that the links are not aligning themselves properly.
Second, a torque wrench should be used for two different reasons. The first reason is that anyone watching a video like this may be a novice, and they should not be encouraged not to torque the axle nut to the manufacturer's specification. The second reason is that V-Strom swingarms have a history of developing cracks near the axle, and excessive torque may be a factor there.
Third, most folks who use the chain to keep the axle up against the adjusters while it is torqued use a soft rag or towel in between the chain and sprockets, rather than a hard tool.
Also, someone suggested this guy might be from the western United States. I doubt it. He specified the chain slack in centimeters, and the accent isn't quite right.
He's Dutch because we loosen de nuT and Taiten de chain 😆
I think in the manual it says to check the slack with the bike on the side stand. Where it would be smaller than the central stand.
Also it says it's between 2 and 3 cm.
True! This is because manufactures often dont supply the bikes with centrestands. So they cant put that in their manuals. You can do it both ways :) basically the same
yes; mine doesn't have it :(
but mind you it's not the same; because chain tension changes with the swing arm's travel; i guess the risk is to bottom up your back shock but not on the shock but on the chain not being able to give in more;
@@emilferent23 true. Process is the same. Just the slack should be kept in account :)
I'd rather have it on the loose side, 3-4cm, long travel suspension on the vstrom, if you are heavy or 2 up fully loaded I wouldn't like the chain to be too tight, puts too much stress on the output shaft.
Is 2-3cm with the rider on the bike? I'm abit worried with that much slack as when I sit on mine the rear shock compresses quite abit
🙏thanks. I’ve now learnt that I need to have it on the centre stand.
Thanks for the instruction! Very helpful!
IIRC the bike should be on the side stand when you measure the slack, otherwise the chain might end up too tight, which is worse than too loose. And if you have a torque wrench handy you should check the axle nut torque -- 100 N-m.
Peter Beens thanks for the comment!
I find it easier to do it on the centre stand. I take in account to leave a little slack extra.
but like all the bike maintenance. keep a close eye on your owner manual or service manual ;)
How so?
Bearded_vstromrider_reviews if you use a paddock stand you get a true reading of the chain slack.
I think what Peter is saying is that with weight on the rear wheel you can see the true chain slack but if you use a center stand it may stretch a little more after you put weight on the rear wheel
72.5 lb-ft
Great video could you do inches as well thanks
regardless of bike the the swing arm should be in line with the rear axle & the swing arm pivot point and the drive sprocket centre shaft (that is normally hidden under a cover.) if you do it any other way you will over tighten the chain !
Thanks for a helpful video.
Thanks! Great tutorial👍🏼👌🏻
Thanks!
Don't see much vids yet on the 1050xt wich i have...but this is the same applied to..
Did it first time thanks heaps 🎉🎉🎉
I’d recommend using a torque wrench on the 24mm bolt. I read 72.5 lbs in a service manual, but verify yourself for your bike . . .
So mellow.
Well done , now let's go ride.
Paul Silva, Let's do that :D
Next video: how to change a chain cover.
Good helpful video, great job. Thanks for this.
Chris Everett you're welcome glad you found it helpfull.
Never showed the slack after the job was done
Subbed to get you away from 999 😂
Surely you didn't let the chain go that slack before deciding to adjust it. That's a good way to destroy your cogs as well.
Thanks I'm guess Minnesota or South Dakota accent am I correct 🤣
bud that’s like a netherlands accent
Not in MN,IA, SD etc. I live in MN . Probably Netherlands-good basic information.
judging by how much you had to pull the wheel back, that chain needs to be replaced. But since this video is almost 3 years old, I am pretty sure that chain is gone by now :)
Man I just realised had video on 1.5x speed, I’m afraid if I put it on normal, the video will be weird
So your gonna make sure you did everything exactly perfect ,,,and then you leave the screwdriver in the chain without taking It out
That chain is shot anyhow. Links are linked. Bad x rings.
Should have taken the screw driver out. I believe your chain is to long, maybe worn or too many links
great effort sir but...
...chains on DL650's are adjusted on side stand, not centre stand.
The measurement will be incorrect using the centre stand and be too tight.
...a chain that is is too loose is better than a chain that is too tight, obviously correct tension is better all round.
NB sorry I see this has been mention before
chain should always be adjusted with bike on the ground. not on center stand.
ur ass
@@roadwarrior8560 NO! My transalp´s chain is measured in center stand!
And uh... don't forget to pull the screwdriver out before riding off XD
Yeah that would be interesting!!
hay que ser malo para tener esa holgura y encima hacer un video.......