Bro I like your video it is very helpful, but i have a doubt , in the video u have used different digital pins for led , not as the same digital pins which is used in one board. So this make it difficult when there is a need to connect more appliances to one board cause the digital pins will be repeated in multiple boards and therefore when we give the command to a digital pin ( for example d5) using blynk platform , all the boards's D5 pin will be set high isn't it . So bro is there any remedy for this issue. If so can u make a video about this one
Hello, first of all thank you for the helpful video! I want do control a nema 17 stepmotor and parallel in other rooms I want to control relais. Know I don't know how to set up the code. Do I have to flash the code like yours with the extra part for the stepmotor on every ESP module? Or do I just have to make sure that every ESP module has the right authentication code? Thank you!
hello sir, thank you for this tutorial. i am getting started with ESP32. I am doing the project where i want to connect five ESP32 to one ESP32 and then , control all the other 5 ESP's GPIO pins with one using android app.so that i will have to connect only ESP to WIFI and not all. the connections should be 2 way so that main ESP will sent commands as well as get to know the status of others ESP. what do we call this method of connecting? how to achieve this any tutorials or reference materials?
Thanks for your technique, exceptional good video, patience and the hard working behind all of these. Is it possible to make the AC Dimmer which runs both Blynk app by using slider button (or "+ve" & "-VE" buttons instead of slider ) and two physical touch sensor switches (say 4 pcs TTP223 or 1 PCS TTP 224 for controlling 4 steps ...etc. ) for manual Control (Increasing or decreasing the bulb intensity or fan speed ) , If so please make a video particularly in coding part, It is difficult to relating the physical two buttons with Blink slider in coding part. It is more better to add 2 more button for controlling 2 ac loads (Just on and off ). Thanks
connect 220v AC Relay With Your 220V Feedback And Operate Relay Coil By The 220V Feedback Then Connect Esp8266 Ground Terminal With Relay Common And Get Gnd Output From Relay Open Point When Relay Is On
Sir nodemcu disconnect from blynk server after 8-9 hours I am running my project continuosly from 3 days. Then I have to manually reset the esp8266 board to run. Please help me out
Thanks for sharing such an Awesome project. In the last segment of this video you have shown that the same analogy can also be applied to physical switch feedback project. As you you , we have 2 position toggle switches in our light switch boards. Can you please modify & share the code to use these same switches instead of push switches show in the video. This would make this project more applicable to majority of people to be incorporated into their existing switch boards. Awaiting your earliest response. Thanks & kind regards.
Followed along with you create only one button, received the token in my email added it to the suggested sketch with SSID, USERNAME, and TOKEN. Press the PLAY button in the cell phone app and a smaller icon in the upper right-hand pops comes up with a red dot. I touch the icon with the small red dot and a small slider drops down and it contains the following note: "Wasn't online yet". Surfed the web and found many folks stuck at the same error message. How do I fix this?
Make sure your board is properly power on or your internet connection is working normally or the authentication code, wifi credentials may not be properly entered
Assalamu Alaikum, how are you dear brother? I watch the videos you make carefully. I really like your videos. Brother, you know that many bikes are stolen in our country. So to prevent this theft, can you create any such device? Which will be high security. Which will have motion sensor alarm system. Using a radio remote to control the bike. The bike can be controlled via mobile bluetooth, wifi, internet. Even the location of the bike, tracking, real time video, etc. will all be pitchers.
😍you can't imagine how I thank you for your videos❤️ I know it’s a big project, but can you make a project for making our very own application, making our own servers and everything with no need for blynk and connect it with our hardware ...to make it a market product and upload this application to google play for example.
Thank u mate for asking this question... I didn't even realise about this problem.... But after thinking a lot I found a solution... Step1: After u create your project, get into the settings page of your project. Step2: U can see a menu named "devices" , click on it.. Step3: now u can see an option named "new device", now u can define and add all of your other boards Step4: now, when u add ur widgets and define the pins, u can now select any of the board and can use all of the pins. I guess this will surely answer ur question.... But if u didn't understand any of the above, pls ask me again.. I'll answer it..
Nice Work If it is Possible their is no internet and we on off switches With mobile App And Mobile Wifi But no Internet If it possible plz help me Sir thanks
Yes u can do it by getting into your projects setting page and turn on "shared access" .. this will cost u 1000 energy, if u don't have enough u have to purchase it... Then generate a QR code, now u have to scan the QR code in your other device... But this should be scanned before logging in ur blynk account or it won't work
Bhai ek aisa video bano jisme ham jisko jisko chahe face lock dare us ko hi pahchane or koi dusra ho to Nahi pahchane. Or Bhai aap se aisa ho Sakta hai ki nodemcu me aisa program dare jisse koi bhi kuchh bhi puchhe vah us ka answer bole. Or koi koi bhi gana Ka name bole vah play Kar de us song ko . Bhai bas itna samajh lo pure Google assistant ki Tarah Kam kare. Bhai please ho sake to is par bhi ek video banao Mera to manna hai abhi tak RUclips par aisa koi bhi Nahi Jo Aapke jaisa samjhata hai.please reply kijiye ga.
Very innovative project.. Keep it up brother !! 👍 Such quality content is hard to find.
Bro I like your video it is very helpful, but i have a doubt , in the video u have used different digital pins for led , not as the same digital pins which is used in one board. So this make it difficult when there is a need to connect more appliances to one board cause the digital pins will be repeated in multiple boards and therefore when we give the command to a digital pin ( for example d5) using blynk platform , all the boards's D5 pin will be set high isn't it . So bro is there any remedy for this issue. If so can u make a video about this one
How many relays can esp32 wroom handle
Super,thanks for sharing. Do you have the same possibility on blynk 2.0?
A push button on the room's Esp8266 can control the Esp 8266 kitchen relay?
Sir!
Two houses are 200-300 meters away using same broadband router. How to send switch command to another house using node mcu?
Hi can we use 5 to 6 esp32 in the same manner which you have used does frequency of the esp32 makes mix match?
Hello, first of all thank you for the helpful video! I want do control a nema 17 stepmotor and parallel in other rooms I want to control relais. Know I don't know how to set up the code. Do I have to flash the code like yours with the extra part for the stepmotor on every ESP module? Or do I just have to make sure that every ESP module has the right authentication code?
Thank you!
Great work. Always waiting for your videos. 😍
can I use ESP01 instead of ESP8266 ?
hello sir, thank you for this tutorial. i am getting started with ESP32. I am doing the project where i want to connect five ESP32 to one ESP32 and then , control all the other 5 ESP's GPIO pins with one using android app.so that i will have to connect only ESP to WIFI and not all. the connections should be 2 way so that main ESP will sent commands as well as get to know the status of others ESP.
what do we call this method of connecting?
how to achieve this any tutorials or reference materials?
thanks for detailed tutorial. can u make different gerber files for 1 relay and up to 10 relays? it will really help.
Super project 👍👍👍
Thanks for your technique, exceptional good video, patience and the hard working behind all of these. Is it possible to make the AC Dimmer which runs both Blynk app by using slider button (or "+ve" & "-VE" buttons instead of slider ) and two physical touch sensor switches (say 4 pcs TTP223 or 1 PCS TTP 224 for controlling 4 steps ...etc. ) for manual Control (Increasing or decreasing the bulb intensity or fan speed ) , If so please make a video particularly in coding part, It is difficult to relating the physical two buttons with Blink slider in coding part.
It is more better to add 2 more button for controlling 2 ac loads (Just on and off ). Thanks
From where I can download the libraries because I can't program the esp8266
U r using small switch and low voltage for the feedback system but how can we use feedback for 220 v ac??
Yes Exactly. Do you know any switch like that? I'll really appreciate it if you can help us with it. Thanks.
connect 220v AC Relay With Your 220V Feedback And Operate Relay Coil By The 220V Feedback Then Connect Esp8266 Ground Terminal With Relay Common And Get Gnd Output From Relay Open Point When Relay Is On
Fine Automation didn’t understand the replay
Good luck
What is the name of the green color board in the background
But can we use all gpio pins in all nodemcu boards?
Sir nodemcu disconnect from blynk server after 8-9 hours I am running my project continuosly from 3 days. Then I have to manually reset the esp8266 board to run. Please help me out
hola como lo harías con un interruptor y no con pulsador ?? gracias
Thanks for sharing such an Awesome project. In the last segment of this video you have shown that the same analogy can also be applied to physical switch feedback project. As you you , we have 2 position toggle switches in our light switch boards. Can you please modify & share the code to use these same switches instead of push switches show in the video. This would make this project more applicable to majority of people to be incorporated into their existing switch boards. Awaiting your earliest response.
Thanks & kind regards.
Can I add energy sensor in this project?
Thank you, man! Your video is awesome!
Sir, pls uploade a vedio of home automation, it consists 16 Chanel relay, each realay control manually + IR+ BLINK
Followed along with you create only one button, received the token in my email added it to the suggested sketch with SSID, USERNAME, and TOKEN. Press the PLAY button in the cell phone app and a smaller icon in the upper right-hand pops comes up with a red dot. I touch the icon with the small red dot and a small slider drops down and it contains the following note: "Wasn't online yet".
Surfed the web and found many folks stuck at the same error message. How do I fix this?
Make sure your board is properly power on or your internet connection is working normally or the authentication code, wifi credentials may not be properly entered
Thanks 😊👍
Wie macht man das mit 4 Boards???? bei den 9Kanal?
Den 4 Kanal finde ich nur diesen für 4 Boards leider nicht. Bitte um Hilfe
Oh you are so good! I also want one but I don't know how to control 1 esp8266 from 2 phones. can you make a video tutorial Thank you very much pro
How to create our own app
Sir if you about the Flutter App development
Please make a video on these multi home automation app
Please please
I do this but this range only on WiFi range I want do anywhere from world pls help me.
Bhai ap ka kam kafi axha hy ap ki video dakh k mn ny 2 project bnay but ux mn thora issue aara hy mjhy .plz us k liy mjhy guide krna.
Home automation king
Thank you for the code !!! Subbed
Appreciated your work
Sir ihave faced 1 problem when i upload blynk code in my nodemcu uploading is done but error
Leaving
Hard resetting with rst button or nodemcu
Assalamu Alaikum, how are you dear brother? I watch the videos you make carefully. I really like your videos. Brother, you know that many bikes are stolen in our country. So to prevent this theft, can you create any such device? Which will be high security. Which will have motion sensor alarm system. Using a radio remote to control the bike. The bike can be controlled via mobile bluetooth, wifi, internet. Even the location of the bike, tracking, real time video, etc. will all be pitchers.
Loved It just awesome
😍you can't imagine how I thank you for your videos❤️ I know it’s a big project, but can you make a project for making our very own application, making our own servers and everything with no need for blynk and connect it with our hardware ...to make it a market product and upload this application to google play for example.
Very nice video bhai 👍
Is there a way to uniquely identify one of the four ESP8266? Because ports used in esp#1 will not be usable in esp#2. Thanks in advance :D
Thank u mate for asking this question... I didn't even realise about this problem.... But after thinking a lot I found a solution...
Step1: After u create your project, get into the settings page of your project.
Step2: U can see a menu named "devices" , click on it..
Step3: now u can see an option named "new device", now u can define and add all of your other boards
Step4: now, when u add ur widgets and define the pins, u can now select any of the board and can use all of the pins.
I guess this will surely answer ur question.... But if u didn't understand any of the above, pls ask me again.. I'll answer it..
Jabardast waiting for ur silver play button
By the way in which college do you study?
Nice Work
If it is Possible their is no internet and we on off switches
With mobile App And Mobile Wifi
But no Internet
If it possible plz help me
Sir thanks
How to know which devices are online??
Really appreciative bro
Can u make video's to understand aurdino software
How to use 30 channel relays
Sir, can i used 1 or 3 cellphone as monitoring for this kind of automation project?
Yes u can do it by getting into your projects setting page and turn on "shared access" .. this will cost u 1000 energy, if u don't have enough u have to purchase it... Then generate a QR code, now u have to scan the QR code in your other device... But this should be scanned before logging in ur blynk account or it won't work
And another method is to login your blynk account in another device and use your project
3 to more device use in one nodemcu ???
What can do??
Amazing bord
From indonesia 👍👍👍
can u do a video on unlimited drone range plz using nodemcu and mini wifi router
My conly problem is the my priject runs on esp32 nd the board disconnects from wifi aftr 20 to 30 mins
Is it work without net
Bhai ek aisa video bano jisme ham jisko jisko chahe face lock dare us ko hi pahchane or koi dusra ho to Nahi pahchane.
Or Bhai aap se aisa ho Sakta hai ki nodemcu me aisa program dare jisse koi bhi kuchh bhi puchhe vah us ka answer bole.
Or koi koi bhi gana Ka name bole vah play Kar de us song ko . Bhai bas itna samajh lo pure Google assistant ki Tarah Kam kare.
Bhai please ho sake to is par bhi ek video banao Mera to manna hai abhi tak RUclips par aisa koi bhi Nahi Jo Aapke jaisa samjhata hai.please reply kijiye ga.
How i learn aurdino software
16 channel relay can control esp32 wroom
Please make a ESP 32 wroom 16 channel relay control module 👍
Waiting for your response 😜☺️
I am watching lots of video but not find esp 32 wroom 16 channel relay control module 👍
Pls make a multiple room lock using aurdino with blynk
Life estimation of nodemcu or esp32
Buddy apni website pe ek comment section dalo jishe ki aagr koi error ho toh resolve ho jaye
Very smart !!!!! bro
Pleae make project to control Air conditioning temperature and fan speed
Hi make a Alexa automation with feedback with buttons from Alexa app
I will try it soon😃👍
Try Sinric
Super
Circuit diagram and files ...plz share
great work!
if your app created with android studio it is very useful ..
Nice
Hi sir,do u teach also
please Make a project on "ARDUINO UNO with ESP8266 & 8 CHANNEL RELAYS" and program it..... 🙏🙏🙏🙏🙏
Tengo 3 esp para mi casa en mi caso las controlo con alexa
please make a “PROGRAMMING" video on “ARDUINO UNO with ESP8266 $ 8 CHANNEL RELAYS" and control by Android phone....🙏🙏🙏
I like that u didn't write a single line of code u smartas* :D
Do
You
Know
Who
Can
Do
Arduino projects & Electronics projects etc
In
perfect
Manner
With
proper
Explanation
In
RUclips
Hint :- See the second line
Please share code
I like it :) Good Video :)
Good luck
nice
Garbar file de sakte hai
boy you should use single nodemcu if u are not going to use same pins on other nodemcu's
Who needs resistors? Certainly not you.
I see you don't answer any questions below
💓💓
Not much info
Please use hindi
Damn✌️
Без скетча полная шляпа.
SCAMMERS --- DOESN'T WORK... DON'T BE FOOLED
Nice video,,bhai aapna number send kar sakte ho
Bhai ap ka kam kafi axha hy ap ki video dakh k mn ny 2 project bnay but ux mn thora issue aara hy mjhy .plz us k liy mjhy guide krna.
nice