How to Replace Driver Side CV Axle 2008-2012 Honda Accord

Поделиться
HTML-код
  • Опубликовано: 25 окт 2024

Комментарии • 34

  • @TRQ
    @TRQ  2 года назад +6

    √ Watch the Video
    √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
    √ Do it Yourself
    √ Save Money

  • @atomiclife9900
    @atomiclife9900 Год назад +11

    Just did my axel shaft. Waiting on the following days to check everything is still in order. Thank you for sharing your knowledge. Saves me at least 500

  • @gioo2961
    @gioo2961 Год назад +6

    This Honda loves you ! 😂 but in all seriousness thank you for providing these videos they have helped me a lot! Keep up the great work 👏🙏

  • @josemarrero7982
    @josemarrero7982 9 месяцев назад +3

    I love your videos man! Straight to the point, very elaborate but also quick to the point with everything and all the parts. I would love to know what digital torque wrench(s) you used tho.

  • @igor_2368
    @igor_2368 Год назад +1

    Thanks to youre video, i already replace all 4 shock struts on my 2008 Honda accord sedan

  • @ernestoavila6370
    @ernestoavila6370 Год назад +3

    Very helpful, thank you for taking the time to do the video.

  • @wilurbean
    @wilurbean 7 месяцев назад +2

    Why is the trq axle missing the balancing ring on the intermediate shaft?
    Did you guys not use new seals?

  • @unathandavis
    @unathandavis 3 месяца назад +2

    I usually leave the upper ball joint in tact and remove lower ball joint and tie rod so the whole knuckle pivots out at the bottom

  • @nathanbowers4484
    @nathanbowers4484 Год назад +2

    Well I messed up changing out my shocks and springs thanks!

  • @_MuscleRussell
    @_MuscleRussell 15 дней назад

    How you gonna do all the steps and leave out the lower ball joint ????

  • @LibertyAppliance
    @LibertyAppliance Год назад +4

    I may have missed it in the vid, but don't you have to preload the suspension before torquing everything?

  • @hieple1714
    @hieple1714 2 года назад +1

    You do very good job easy learning but I like your tools where you buy that’s tools..? Thanks

  • @danielquaternik22
    @danielquaternik22 Год назад +1

    My lower ball joint broke pulling the axle out of the metal part you are prying to get out of the transmission. It does not want to come out!! Any assistance would be greatly appreciated!!

  • @RookieHomeImprovement
    @RookieHomeImprovement 2 месяца назад

    What type of grease/brand name grease should we use on the splines that go into the hub?

  • @Jez1963UK
    @Jez1963UK 4 месяца назад

    I noticed that the old CV Axle had a damper on it while the new one didn't. How come? I'm only asking because the damper on my axle is beginning to perish and was looking at getting the damper replaced only to learn that the part is discontinued.

  • @nicholaspetre1
    @nicholaspetre1 Год назад

    superb video I must say!

  • @brandonconerty7557
    @brandonconerty7557 10 месяцев назад

    In my personal opinion after doing the hub assembly and lower ball joint on this side id remove the whole knuckle just to get it full out of the way and the axle with be easier to remove

  • @pull4adventures
    @pull4adventures Год назад

    Just installed the A1 auto axles and now I feel vibrations under load at 15-30mph. Any ideas?

  • @305tyrone4
    @305tyrone4 Год назад +4

    Does this work on the v6 too?

    • @atomiclife9900
      @atomiclife9900 Год назад

      idk about the part . but its the same process for all 2008 to 2012

  • @hoodvinesfightsclips4557
    @hoodvinesfightsclips4557 Год назад

    Great video

  • @pt280
    @pt280 8 дней назад

    I don't get it at 11 .49 the hub bearing is old but few seconds later is brand new... 11.53

  • @jimlelan4906
    @jimlelan4906 7 месяцев назад

    Seams like you would want to inspect the old axle shaft seal.. before putting it all back together…?

  • @gottosahani7571
    @gottosahani7571 9 месяцев назад

    Thanks

  • @seanpinson9030
    @seanpinson9030 9 месяцев назад

    That subframe needs sanding and a good undercoating followed by surface shield

  • @elromanicobaby
    @elromanicobaby 10 дней назад

    Mine was easier to take out because it split in half 👏🏼

  • @TheMaxima2004
    @TheMaxima2004 11 месяцев назад

    That left side rotor should be on the right side. reason those hole patterns should be spinning the downwards not upwards

  • @itstinyverdugo2571
    @itstinyverdugo2571 Год назад

    Doing this job with my brother this weekend I’ve been driving with Shot Axel Bearings since I bought the thing but once said and done it’s still a certified shit box

  • @zachrobins3763
    @zachrobins3763 Месяц назад

    Trans fluid dumped to the floor thanks

  • @chinhphan4787
    @chinhphan4787 Год назад +7

    I foresee a lot of people snapping bolts with their impacts.

  • @jacobkeyser8628
    @jacobkeyser8628 6 месяцев назад

    Firestone is want 400 for just my cv. With this and help my friend I can do it for 130 and pizza

  • @AlexofSmeg
    @AlexofSmeg Год назад +1

    Go ahead. 🤦

  • @impersonalopinion
    @impersonalopinion Год назад +1

    what a rust bucket