I would say your statement may be true. I do not see any evidence that proves otherwise. However, theoretically a toothbrush is maybe not quite stiff enough to dislodge things as well.
Do you recommend avoiding Pad Washers like the Lake Country System 4000 to clean pads as you move the pad from section to section? My problem with them is, even after spinning the pad after cleaning it, the pad still has some solution, even a small amount, in the pad and I often wondered if that would interfere with the polish. I am fine with them when it is time to retire the pad for the day and you will be grabbing a clean pad to continue polishing but I have always had an uneasy feeling about using them on the go if my question makes sense.
We do not have a preference either way - I think there is a place for the pad washers for sure since it is SOOOO MUCH work to clean them after but on the fly during the job I lean towards the methods I mentioned here. It is possible and likely that any residue form the cleaning solution WILL change the polish or compound and pad SOME but in most cases it should not be a concern. Basically, I wouldn't worry about it unless you can notice a time loss or lessening of the quality of finish with a certain combo after using it.
What if we wash the pad, put it on the machine on maximum speed to rinse it off and then continue with our compound/polish again. And finish off the car with one pad. That way we always keep the pad cool as well as prevent dusting. What do you think? (this is Ivan`s method)
Thanks! Well, I try not to overthink it on the pad cleaner... Any APC you keep in your arsenal or even a microfiber cleaning soap. Have some in a bucket and then spray a little P21S total auto wash on the face of the pad when you take it off and drop to face down in the bucket. P21S because I feel like it is less likely to deteriorate the foam when sprayed directly on it... MFX from CARPRO would be even safer but maybe not remove polish residue as well. Both are good options I believe.
Hi great video and tips! Im just getting into polishing. I want to polish my car but, i don’t want to invest too much at the moment. At firsti was just going to hand polish, but after watching a few videos i realized it was going to be a long and tiring job so i decided i would just buy a cheap DA. Im not expecting much out of it but it would be 100% better then elbow grease right 😂 Will i be okay to use one pad all around the car. Giving it time to cool off after each section? I will not be using air by the way just the brush. Thank you!😊
Hi Aren, yes... WAY easier by machine. Great idea! I would get at least 2 pads. You can get by with 1 pad assuming it does not delaminate. While not optimal and certainly slower as it gets more clogged as you go, you can do it.
Dude, don't do it by hand. Harbor Freight makes a decent dual action polisher for around $50. Foam pads about $10 each. Your elbows and shoulders will thank you later.
The short answer is yes. A pad like this would be capable of both www.carpro-us.com/latest-arrivals/skys-the-limit-5-1-2-cutting-blue-spider-pad/ But if you want heavier cut then you would go even heavier on the pad like the Sandwich Spider and if you wanted optimal finish, on some paints you would be better off with the Honey Spider. All depends on your goal, and the paint. You can vary the pad, the compound, the speed, the pressure, or a combination of these to achieve those results.
Awesome 👌 video. This is exactly what I was looking for. Super good! 😊
How cool! Thank you!!!
@@SkyCarCare 😊
Merry Christmas and a great new year!
May you continue making videos.
Merry Christmas to you!!@@jaimedpcaus1 May your Christmas and all of 2024 be filled with peace, joy, and loving people!
More than a few top tips in here, solid valuable advice as usual - excellent, thank you.
Thanks Andrew!
Many thanks!! Excellent nice & short video. It confirmed the way I was doing it without those expensive liquid par cleaner pump bucket!!!
Excellent! I am grateful it was helpful!
Corey
i feel like an old tooth brush works just as well right?
I would say your statement may be true. I do not see any evidence that proves otherwise. However, theoretically a toothbrush is maybe not quite stiff enough to dislodge things as well.
Can i like soak the foam pad after 1 panel and them free spin it? would it be too wet and dilute the next polish liquid
Depends on the polish but generally speaking you can certainly do that.
Great information! Thank you for sharing this.
Our pleasure! Glad you found it useful!
Can 3inch backing plate be used in 5inch size polisher? I see no one did this.
No, 3" plate will not work right on a 5" machine.
How many pounds of pressure would you recommend on the compressor? I’m thinking lower is safer. Thanks
I completely agree, it doesn't need a huge amount of pressure.
Do you recommend avoiding Pad Washers like the Lake Country System 4000 to clean pads as you move the pad from section to section? My problem with them is, even after spinning the pad after cleaning it, the pad still has some solution, even a small amount, in the pad and I often wondered if that would interfere with the polish. I am fine with them when it is time to retire the pad for the day and you will be grabbing a clean pad to continue polishing but I have always had an uneasy feeling about using them on the go if my question makes sense.
How long and what speed are you spin drying your pads?
@seventysschev As fast as possible to remove as much liquid as possible.
I use ONR in my pad washer and it works great being slightly damp!
When I use a foam pad after the pad washer the pad feels softer and I think it decrease the cutting capabilities. But it cleans the pad amazingly good
We do not have a preference either way - I think there is a place for the pad washers for sure since it is SOOOO MUCH work to clean them after but on the fly during the job I lean towards the methods I mentioned here. It is possible and likely that any residue form the cleaning solution WILL change the polish or compound and pad SOME but in most cases it should not be a concern. Basically, I wouldn't worry about it unless you can notice a time loss or lessening of the quality of finish with a certain combo after using it.
What if we wash the pad, put it on the machine on maximum speed to rinse it off and then continue with our compound/polish again. And finish off the car with one pad. That way we always keep the pad cool as well as prevent dusting. What do you think?
(this is Ivan`s method)
Some pads may work fine like that but there are also some that may be more prone to delamination if you introduce water to the pad while polishing.
@@SkyCarCare Delamination of what? The velcro?
Yes@@flowinthrou
@@SkyCarCare Thank you, you are very helpful
love those velcro buttons, never seen them before. what are you using as a pad cleaner ?
Thanks! Well, I try not to overthink it on the pad cleaner... Any APC you keep in your arsenal or even a microfiber cleaning soap. Have some in a bucket and then spray a little P21S total auto wash on the face of the pad when you take it off and drop to face down in the bucket. P21S because I feel like it is less likely to deteriorate the foam when sprayed directly on it... MFX from CARPRO would be even safer but maybe not remove polish residue as well. Both are good options I believe.
Hi great video and tips! Im just getting into polishing. I want to polish my car but, i don’t want to invest too much at the moment. At firsti was just going to hand polish, but after watching a few videos i realized it was going to be a long and tiring job so i decided i would just buy a cheap DA. Im not expecting much out of it but it would be 100% better then elbow grease right 😂 Will i be okay to use one pad all around the car. Giving it time to cool off after each section? I will not be using air by the way just the brush. Thank you!😊
Hi Aren, yes... WAY easier by machine. Great idea!
I would get at least 2 pads. You can get by with 1 pad assuming it does not delaminate. While not optimal and certainly slower as it gets more clogged as you go, you can do it.
Dude, don't do it by hand. Harbor Freight makes a decent dual action polisher for around $50. Foam pads about $10 each. Your elbows and shoulders will thank you later.
Can one pad be used for both compound and polish? Assuming you cleaned in between...
The short answer is yes. A pad like this would be capable of both www.carpro-us.com/latest-arrivals/skys-the-limit-5-1-2-cutting-blue-spider-pad/
But if you want heavier cut then you would go even heavier on the pad like the Sandwich Spider and if you wanted optimal finish, on some paints you would be better off with the Honey Spider. All depends on your goal, and the paint. You can vary the pad, the compound, the speed, the pressure, or a combination of these to achieve those results.
All talk and no demo
Sorry it was not what you were expecting! Hopefully we described it clearly enough to offer some tips.
You got a punch on the side of your face
No, but good guess!
@@SkyCarCare
Road Rash from skate boarding or from skiing on hard pack snow.
Lol, Gua Sha from my doctor to free my nasal congestion from a bug I had @@optimoprimo132
Black eyes club😮