Hello, what a good video. It's a shame I don't speak English to appreciate it even more. I am writing to you from the translator hahahaha. Thank you very much for helping the community with your knowledge. I have a DJI Mini 3 with error 40011. Will these steps help me? thank you so much.
Hi there. Thank you for commenting! I cannot promise that this will help you. If you had an accident with your drone the issue could be hardware related but give it a try! You have nothing to loose.
@@InfinityDrones Hello Friend how are you? Download the firmware for gimbal calibration. but the drone-hacks application does not advance me in the process. remains at 0. Do you have any suggestions why? I clarify that it recognizes the drone and I can load the firmware. thank you.
@@jharrymorales1648 leave it for 10 min, if the drone did not restart during that time it did not work. Try a different machine. Make sure you have the Dronehacks driver installed and dji assistant 2 for consumer drones
@infinity drones, if you have an air 2s, an rc pro controller & an rc controller. Which controller is best to keep to maximize the hack from drone hacks? I see in their bird map that RC pro doesn't really have much hack available. But I don't see anything for RC controller. Can air 2s still have the ability to use maximum hacks available from drone hacks & be controlled by RC pro?
@@InfinityDrones o excellent 💯 that is great news. I was concerned RC pro would transmit drone ID & also lose NFZ hack capabilities. Thank you for your insight & knowledge
Thanks for all the detail steps. Did you try this on the Mavic 3 pro? In my case of Mavic 3 pro, the process stuck at 78% then the calibration is failed. Looking forward to your reply.
Follow the video and check if there firmware available for your ARB verison. I also have a video using a phyton script as well on the channel, worth a try.
Sadly no it will not. Seems like a hardware issue... Might be a roll or pitch motor but most likely your PTZ cable is starting to go. You'll have to send it in for repair as it would need to be recalibarted.
Hi, after replacing the gimbal, I can't turn on the drone after connecting the cable to the PC. How do I get into DFU mode to update the drone using the drone hack? I have DJI mini 2
So you can power on the drone? If you can you mist follow the mini process (when you open the application you'll be able to see the "mini connection process") just follow those steps
@@InfinityDrones in order for the drone to see the PC, I must first turn on the drone and then connect it via USB to the PC. Otherwise, the drone cannot be turned on, but I have already managed to update the drone, it's just that the drone does not see that the camera is connected and I only see darkness
I bought firmware version for mavic mini 2 for service but still no possible to perform calibration;( There is button Auto but is no active;/ also manual not possible.. any ideas?
@@InfinityDrones I tried the same version of ARB it's only one with 4 so there was no mistake..I changed the signal cable and maybe I put something back to tide? Not sure its possible🤔 Everything in app works good except for moving the gimbal (even by stick)
Are you trying to flash a different ARB level firmware? Remember if your Anti Roll Back version is 5, then you can only flash firmware of ARB 5 or higher.
Hi, on my DJI mini current version. 01.00.0600. I have downloaded 01.00.0320 but drone hacks require a license. which version should I download to resolve the gimbal calibration error?
@@InfinityDrones I have tried flashing with the same arb as the firmware type on the drone unit but still no results. Do you have other tools to flash firmware other than drone hack, friend?
hi dear hope you are doing well i need some help dear i have a mini 3 pro but the controller bound with my mini3 pro i lost and i conect my drone to new controller dji rc n1 its showing device bound to another account please give me some help to resolve my issue thanks
Thanks for reply dear I buy a unbind motherboard on my mini 3 pro and than gimbal calibration need only right so I can calibrate gimbal from dank drone
@@borisbahleda2989 The software can't damage you rdrone, so give it a try. But as far as I know if you change hardware you'll need to load new calibration firmware - I have a video about that too.
They are not the same, fundemental firmware changes means that the same approach on the Mini 3 pro will not necessarliy work on the Mini 3 - Also, the guys are trying their best to source calibration firmware, but DJI are keeping the system very closed - so very difficult for the guys at DankDroneDownload if dji does not officially release firmware.
hey! i have the camera calibrate error and wont let me record footage from the drone either now only from the goggles in my dji fpv drone after i changed the gimble to another onei looked at that python way to calibrate the gimble but it doesnt say it supports my dji fpv drone:( does anyone have any ideo of what i can do to fix it please? its so annoying as i use it for capturing footage:(
@@InfinityDronescamera calibration error on the goggles V2. They say you need to calibrate on assistant 2, but, when you try to calibrate there, appears message: calibration failed. That occurred with lot of people and nobody have fixed that issue. I also have this problem with my DJI o3 air unit
@@gabrielnunes159 Camera calibration error is just on the o3 if you replaced the camera. Nothing to do with your goggles. So be sure to update your dji assistant 2 for consumer drone and update the firmware to the latest.
@@InfinityDrones I didn't change the camera. I bought it from AliExpress from a seller with 100.000 followers and more than 90% of approval. I am asking help to them but the time for ask for refund has gone. I am talking to DJI support see if they can help. Don't know what to do, what I know is that DJI makes supposed good products, but they really suck when related to usability.
Hello friend, very good video, how to make the USB port recognize the Mavic 3, on my PC it appears as Libusb and it does not detect the COM port in drone-hacks. Thank you
@@InfinityDrones I think I didn't make myself understood, when I connect my Mavic 3 it doesn't recognize it on any COM port only as a Libusb device, is there a way to configure it so that it recognizes it on any of the COM ports? Thank you
@@eduardongc the mavic 3 uses a different connection method and you won't see it use a specific com port. May I ask why you want to see a come port specifically?
@@user-in7qv5rz6n like I said. Check dankdronedownloader as they store all available firmware. However, mini 4 pro has a calibration issue that dji put in on purpose that requires their software. So you will need to send it on to get the error removed and calibrated.
I do not know... if you crashed your drone (not sure what model) but gimbal stuck is most likely a gimbal motor or ribbon that is faulty. There is a whole host of other possible issues and I cannot confirm that this will work
@@InfinityDrones Thank you. The video says that the website doesn’t have the gimbal calibration firmware, and I need to download the app. Do you know the firmware version I need for a Mini 3 Pro?
@@LRC247 Hi there in the video I show how to download the firmware. Why don't you download the app? The app is the best way to see what firmware are available. Remember firmware is constantly being added to the database. But to answer your question. Yes I have downloaded several mini 3 calibration firmware versions
@@xXDannySilvaXx yeah, the Camera (that came with the drone) is already registered with the Core Board so you don't need the software to introduce to Core Board again. It works on my Mini 3 Pro. Other fixer might have another way to introduce new Camera to Core Board tho.
Thanks a lot ! Now my camera is on the right position. Juste have to check if the drone flight correctly this afternoon
Glad I could help! Thank you so much for sharing a comment :)
Hello, what a good video. It's a shame I don't speak English to appreciate it even more. I am writing to you from the translator hahahaha. Thank you very much for helping the community with your knowledge. I have a DJI Mini 3 with error 40011. Will these steps help me? thank you so much.
Hi there. Thank you for commenting! I cannot promise that this will help you. If you had an accident with your drone the issue could be hardware related but give it a try! You have nothing to loose.
@@InfinityDrones Hello, thanks for answering. It wasn't an accident. It was after changing the gimbal. I hope it works. successes on the channel.
@@Jhamoralesr mini 3 gimbal needs dji official software to recalibrate the gimbal... But give it a go and let me know if it worked for you
@@InfinityDrones Hello Friend how are you? Download the firmware for gimbal calibration. but the drone-hacks application does not advance me in the process. remains at 0. Do you have any suggestions why? I clarify that it recognizes the drone and I can load the firmware. thank you.
@@jharrymorales1648 leave it for 10 min, if the drone did not restart during that time it did not work. Try a different machine. Make sure you have the Dronehacks driver installed and dji assistant 2 for consumer drones
After changing the camera to the mini three, this method will work.
Sorry man, this method does not support mini 3 firmware flashing only mini 3 pro
Brilliant, I wonder what is happening with the drone that this vertical orientation tricks it.
Would like to know that too, but thats the steps they use in the factory as this is the factory gimbal calibration firmware.
@infinity drones, if you have an air 2s, an rc pro controller & an rc controller.
Which controller is best to keep to maximize the hack from drone hacks?
I see in their bird map that RC pro doesn't really have much hack available.
But I don't see anything for RC controller.
Can air 2s still have the ability to use maximum hacks available from drone hacks & be controlled by RC pro?
The rc pro is the best controller to use. Range etc will all be beter. You don't need to mod it at all if you've got an air 2s that's modded.
@@InfinityDrones o excellent 💯 that is great news.
I was concerned RC pro would transmit drone ID & also lose NFZ hack capabilities.
Thank you for your insight & knowledge
@@ElevatedVehicles just a pleasure man
Thank you very much! I used this method on my Mini 2 anf it works! Though there’s still error 40021 (gimbal imu error).
Glad it helped! Did you replace your gumball. 40021 is because the serial numbers of the camera and Coreboard doesn't match.
@@InfinityDronesruclips.net/video/B4a0mh2p5OQ/видео.htmlsi=ygghJBm_r7h0dCcr
@@InfinityDronesEu tenho o Firmware de remoção do erro 40021.
@@AeroByte360 You will need to send the drone in so that the official dji software can be used to calibrate it
thanks, works for me.!
Great! Very happy this helped you!
Thanks for all the detail steps.
Did you try this on the Mavic 3 pro?
In my case of Mavic 3 pro, the process stuck at 78% then the calibration is failed.
Looking forward to your reply.
Hi there, sadly I don't have a Mavic 3 pro to test with. Remember, this is only for error 40011 and also if it's not crash related.
Please bro it work with mini3 pro ? My 3pro didn't send any message after I replaced the gimbal but it is tilted to the right😢😢 help plz
Follow the video and check if there firmware available for your ARB verison. I also have a video using a phyton script as well on the channel, worth a try.
Great video ....How to calibrate module camera mini 4 pro?
Hi there, thank you for commenting. The mini 4 is very new and the firmware has not been release for it yet sorry.
Hello! I have a jelly effect on the video (mini 3 pro) there are no errors, will recalibrating the stabilizer using this method help?
Sadly no it will not. Seems like a hardware issue... Might be a roll or pitch motor but most likely your PTZ cable is starting to go. You'll have to send it in for repair as it would need to be recalibarted.
Will it fixed the 40002 Gimbal error?
I do not know, but worth a try :) Remember that error is not just for a single cause , you could have a faulty motor or cable or or or.
Ran the calibration firmware on my air 2 after replacing the gimbal. It completes successfully, but the error message remains.
The error can only be resolved by official dji software sadly, it's no just a ghost error though
@@InfinityDrones I resorted to using litchi. No error in it.
@@perditionluc yup, since it's a ghost error now. Good workaround 👍
@@perditionlucHi please help. Faceing thé same issue you faced. What is Litchi ? Please help
Hi, after replacing the gimbal, I can't turn on the drone after connecting the cable to the PC. How do I get into DFU mode to update the drone using the drone hack? I have DJI mini 2
So you can power on the drone? If you can you mist follow the mini process (when you open the application you'll be able to see the "mini connection process") just follow those steps
@@InfinityDrones in order for the drone to see the PC, I must first turn on the drone and then connect it via USB to the PC. Otherwise, the drone cannot be turned on, but I have already managed to update the drone, it's just that the drone does not see that the camera is connected and I only see darkness
@@vasiksv3363 then you have a ptz cable that's faulty or a faulty camera
@@InfinityDrones oh well thanks for the info
I bought firmware version for mavic mini 2 for service but still no possible to perform calibration;( There is button Auto but is no active;/ also manual not possible.. any ideas?
So in the fly app its not allowing to calibrate? Have you tried a different version of the firmware, perhaps the antirollback version was different?
@@InfinityDrones I tried the same version of ARB it's only one with 4 so there was no mistake..I changed the signal cable and maybe I put something back to tide? Not sure its possible🤔
Everything in app works good except for moving the gimbal (even by stick)
@@pawelbarge So the gimbal does not more on startup ?
Mine wont flash, ive just read that DJI have made it so its not possible to flash anymore?
Are you trying to flash a different ARB level firmware? Remember if your Anti Roll Back version is 5, then you can only flash firmware of ARB 5 or higher.
Hi,
on my DJI mini current version. 01.00.0600. I have downloaded 01.00.0320 but drone hacks require a license. which version should I download to resolve the gimbal calibration error?
If you need to flash firmware with an older anti rollback version then you need to buy a license
So will this help if i replace a broken camera/gimbal with a nother used one??
In some cases yes, but in othes dji required a dji official software calibration because the serial numbers wont match.
I'm having trouble doing it on the DJI mini 3, the firmware upload doesn't work, is there another way, friend?
Are you trying to flash firmware with the same ARB value or are they different?
@@InfinityDrones I have tried flashing with the same arb as the firmware type on the drone unit but still no results. Do you have other tools to flash firmware other than drone hack, friend?
@@pesantrenluqmanalhakim270 do the firmware flash completes? Did you have a crash?
@@InfinityDrones I didn't experience any crashes or anything like that, but when I flashed the drone hack application, there was no progress at all.
Have you ever tried the flash on the DJI Mini 3, friend?
hi dear hope you are doing well i need some help dear i have a mini 3 pro but the controller bound with my mini3 pro i lost and i conect my drone to new controller dji rc n1 its showing device bound to another account please give me some help to resolve my issue thanks
Sorry... can't help with bound controllers :( I wish dji would just remove this silly bind issue
Thanks for reply dear I buy a unbind motherboard on my mini 3 pro and than gimbal calibration need only right so I can calibrate gimbal from dank drone
@@JawadAhmed-v8f oh ok.
Hi dear please tell me if I buy i new unbind motherboard for my mini 3 pro Whats error comes and the error have solution or not Thanks❤
@@JawadAhmed-v8f you'll still have the 40011 error but it won't affect anything
My mini 3 pro doesn't want to pair with my RC-N1 after flashing calibration firmware. Any ideas why? Thanks.
The calibration firmware is just for calibration, its not meant to fly with. You must flash normal firmware before flight
@InfinityDrones oh I was trying to connect it to the dji fly app so that I can perform the calibration as shown in the video
Hi, did it work? I changed yaw motor on my mini 3 pro, so i dont want to damage drone
@@borisbahleda2989 The software can't damage you rdrone, so give it a try. But as far as I know if you change hardware you'll need to load new calibration firmware - I have a video about that too.
for the dji mini 3 is the same !!!!!! if not possible at this time to flash with this software....why
They are not the same, fundemental firmware changes means that the same approach on the Mini 3 pro will not necessarliy work on the Mini 3 - Also, the guys are trying their best to source calibration firmware, but DJI are keeping the system very closed - so very difficult for the guys at DankDroneDownload if dji does not officially release firmware.
seem good for me to change some value but not flashing .....stay 0% ...but flashing ok with dji assistant
Is there software for mavic 3 vision sensor calibration?
I've not had a mavic 3 in yet, but I'm sure if you follow the steps in the video and check DankDroneDownloader you might be lucky.
Hi, what firmware is for calibrating mini 1 with ARB2?
Hi there, I don't know it off by heart. My video does show you exactly how to find out though.
hey! i have the camera calibrate error and wont let me record footage from the drone either now only from the goggles in my dji fpv drone after i changed the gimble to another onei looked at that python way to calibrate the gimble but it doesnt say it supports my dji fpv drone:( does anyone have any ideo of what i can do to fix it please? its so annoying as i use it for capturing footage:(
What error message are you seeing?
@@InfinityDronescamera calibration error on the goggles V2. They say you need to calibrate on assistant 2, but, when you try to calibrate there, appears message: calibration failed. That occurred with lot of people and nobody have fixed that issue. I also have this problem with my DJI o3 air unit
@@gabrielnunes159 Camera calibration error is just on the o3 if you replaced the camera. Nothing to do with your goggles. So be sure to update your dji assistant 2 for consumer drone and update the firmware to the latest.
@@InfinityDrones I didn't change the camera. I bought it from AliExpress from a seller with 100.000 followers and more than 90% of approval. I am asking help to them but the time for ask for refund has gone. I am talking to DJI support see if they can help. Don't know what to do, what I know is that DJI makes supposed good products, but they really suck when related to usability.
Will this fix also work with IBU database error?
IBU database error? worth a try... but I've never heard of that error before
Its keep getting stuck at 2/2 at 46%... dont know what to do anymore... its for my mini se 1. I tried every firmware update there is
Did you have a crash? It might be a hardware issue then...
When I try to flash firmware it starts but doesnt load even after 10 mins
Do you have dji assistant 2 for consumer drones installed?
i got all the way to running the gimbal calibration on my Mini 2, but it just hangs at 0%
Dis you have a crash?
Hello friend, very good video, how to make the USB port recognize the Mavic 3, on my PC it appears as Libusb and it does not detect the COM port in drone-hacks. Thank you
You need to have a dji assistant 2 for consumer drones installed
@@InfinityDrones I think I didn't make myself understood, when I connect my Mavic 3 it doesn't recognize it on any COM port only as a Libusb device, is there a way to configure it so that it recognizes it on any of the COM ports? Thank you
@@eduardongc the mavic 3 uses a different connection method and you won't see it use a specific com port. May I ask why you want to see a come port specifically?
The commenter above probably wants to calibrate his Mini 3 Pro using Pyserial. @@InfinityDrones
i need air 2s gimble calibration flash file can u plz share is for me ?
It's on the list as per the video. You can just follow the steps
Wondering if the air 3 is available on this application
The Air 3 is still very very new.. you can try and see if the firmware files have been release, but I doubt it will be
There is a calibration firmware for Air 3 but only for ARB 0 (anti rollback value). I doubt you still use old firmware with ARB 0.
Does anyone knows if the DJI Mini 4 pro calibration firmware already available?
Best place to check is dankdronedownloader
Hi, do you test it? which firmware correct?
@@user-in7qv5rz6n like I said. Check dankdronedownloader as they store all available firmware. However, mini 4 pro has a calibration issue that dji put in on purpose that requires their software. So you will need to send it on to get the error removed and calibrated.
Help Me Progress status is showing 0% even after several minutes
Have you tried a different machine?
i crash my drone it will fix it ?( gimbal stuck and calibrate error, not broken)
I do not know... if you crashed your drone (not sure what model) but gimbal stuck is most likely a gimbal motor or ribbon that is faulty. There is a whole host of other possible issues and I cannot confirm that this will work
@@InfinityDronesDji mini 2 se, I accidentally dropped it on the floor.
@@ewyowt Yeah... I think you have a motor or ribbon issue
@@InfinityDronesneed repair?
@@InfinityDronesneed repair? how much repair?
Help! I have gimbal stuck error Error Codde 1D010002 how to fix please??? DJI mini 3 pro
Did you have an accident?
@@InfinityDrones Yes, I had a fall with tree:))
@@s3quatro then I think you have a mechanical problem...
Any FCC or NFZ hack Known for the DJI Mini 4 Pro ?
It's still too new. They still trying to find a workaround for the mini 3... So mini 4 I think won't happen any time soon
No because there is no SDK
what about for mac?
No support for mac sorry.
Dank Drone Downloader won't download on my Macbook Air, do I needa Windows computer for this?
It's a pc app, but they also have a website where you can get everything
@@InfinityDrones Thank you. The video says that the website doesn’t have the gimbal calibration firmware, and I need to download the app. Do you know the firmware version I need for a Mini 3 Pro?
@@LRC247 Hi there in the video I show how to download the firmware. Why don't you download the app? The app is the best way to see what firmware are available. Remember firmware is constantly being added to the database. But to answer your question. Yes I have downloaded several mini 3 calibration firmware versions
@@InfinityDrones It’s not letting me download it on my MacBook :(
@@LRC247 As per the video... mac is not supported. Sorry man
do you have for mavic air 2?
Hi there, check out this video of mine. Should sort you out :)
@@InfinityDronesI already downloaded dankdrones. I don't know what to firmware to download for the mavic air 2 calibration firmware
@@InfinityDronesthis is quite helpful. Thanks! The only question I have is that do I have to buy drone-hacks license to do that?
@@DulaangLaagan no need to buy a license. Watch the video and you'll see you might have to buy the calibration firmware for 1 pound.
@@InfinityDronesI already have 2 credits for this👌 gonna do this later. I am waiting for the gimbal assembly I ordered.
How to remove 40021 error??
This does not sorry. That you'll need to send it because your replaced the camera. The serial numbers don't match...
I did try put back the original camera with the new gimbal (not the whole new gimbal + camera combo) and the errors are gone.
@@yekru7so u just took out the camera out the old broken gimbal housing and put it inside the new gimball housing and that fixed ur problem?
@@xXDannySilvaXx yeah, the Camera (that came with the drone) is already registered with the Core Board so you don't need the software to introduce to Core Board again. It works on my Mini 3 Pro. Other fixer might have another way to introduce new Camera to Core Board tho.
Will this work if you replace the whole gimbal part?
Has anyone had success on a mini 3? Drone hack gets stuck.
did you replace your gimbal or have an accident?
i replace the gimbal. i work fine but it 's a little on the left. i have no error on dji fly @InfinityDrones @@InfinityDrones
@@InfinityDrones yes, but my problem is mini 3 doesn't connect to DH
@@johnsmotors Did you follow the steps of connecting a Mini to the PC? The turn on, wait for chime then only connect the cable?
You need drivers - just install DJI Assistant 2. If it connects then you are ready for DH.
help me, my country not support to donate😢
Hi there, whar do you mean?
After changing the camera to the mini three, this method will work.
Mini 3 pro it might, but this method does not support flashing mini 3 firmware
@@InfinityDronescan you please explain better? Is it possible to calibrate mini 3 pro or not?