Hey buddy.. Good video... 2 things you should say. 1. If the impact is without pressure, it makes sense to set the REC to minimum. With the PP you need less REG pressure. 2. If you secure Hammer Stop with glue or loctite, you should wait until the glue is ready. if you mount the valve spring too early, it is possible that the hammer stop will turn and the dimensions will no longer be correct ... Greetings Rick
Mooi om eens deze kant van Krale te zien. Ik ben een paar maanden geleden voor het eerst op jullie nieuwe adres geweest en moet zeggen, een geweldige winkel. Niet voor niets dat ik als lucht sportschutter, maar ook als voorzitter van onze SV iedereen doorverwijs naar Krale. Goed materiaal, volop keuze, eerlijke prijzen en eerlijk advies. Kan alleen maar zeggen, ga zo door. De groeten van SV Woensel 77.
Weet iemand hoe je aan de 6 tot 6,5 mm komt zoals beschreven in de video? Na installeren en het volledig indraaien van het oude stukje meet ik 8mm. Dus hoe dit aanpassen als dat stukje er al volledig ingevezen is?
What a very good clear example of a great video. I need to watch couple more times before I fit mine. And could not understand your language (sorry) but sub titles were very clear. Thank you.
Duidelijk en fijn dat er een goed filmpje op internet staat ! Heb het plenum vorige week succesvol zonder geïnstalleerd, en het viel erg mee ! Heb misschien één puntje, voor het dichtdraaien van het plenum heb de klepstang iets terug uit het klephuis getrokken, zodat deze niet heen en weer word gebogen.
Only thing I would do differently is not have the valve seated when screwing in the front of the power plenum. It puts stress on the valve rod and the Orings that seal where the valve rod exits the power plenum. The passage through the PP is off set so will put a bending force on the rod. The valve has to be pulled towards the muzzle to install the C1 so it makes no sense to seat it.
That is not the first time you have done that, very professional. I did not see you put the black plastic hammer spring guide back in, off camera?. thank you
@@humphreydavids mine white delron C3 bumper just arived I will replace my MkII on this weekend . And I wait for my dealer to order a Power plenum for me.
@@KraleShooting Three questions: do they have in stock? and there are versions - not original FX - that also consider the modifications to the pellet feeder and the barrel connection ... is there an improvement still pending by FX to improve the greater air flow generated by the plenum? Finally, this original internal plenum of FX is compatible at the same time using it with the external plenum ... as for a larger volume of air? or is it already unnecessary at this level? thank you very much for the help, greetings
@@marcelogalvez9516 1. This product is currently out of stock. 2. We are not aware of any upcoming updates. 3. It would be possible to install an external plenum but we would not advice to do so as there is not need to do that because the FX Power Plenum already delivers optimum power.
Hello, I am looking for information before dismantling everything 😅 on my impact MK2 I noticed a small leak, I located it at the level between the Wheel and the adjuster? what part could this come from? Thanks in advance for the advice.
Hele goede instructieve video. En erg fijn dat de juiste maten worden gegeven. Maar toch enkele vragen. Wanneer de afstand van het uitstekend gedeelte van de hammerseat niet juist is, hammerseat in of uitdraaien tot de juiste lengte? (moet je vlot zijn met die loctite) Wanneer die afstand tussen de probe en achterkant van het huis niet juist is, aanpassen op het blokje voor? Lijkt mij bij beide vragen wel nml. Ik hoop de Power Plenum kit snel binnen te krijgen en kan hem nu zeker goed monteren, er zijn toch wel dingen die fout kunnen gaan zag ik.
Krale Schietsport Kun je de FX 2 Impact ook bestellen met .22 Slug Liner 700mm, zwaardere hamer, en Plenum fabieks af al geinstalleerd. Wanneer komt de MK3 uit.
Hi, followed this but the alignment of the valve housing at one end and plenum end cap hole at the other is way out, meaning that the valve rod is not straight. Way out, like 130° out. I don't want to tighten the end cap more, and there is nothing to grip on anyway, and if I back it out by unscrewing to align the holes the rod goes through, the cap o-ring seal isn't made and air just rushes out. The alignment of the plenum end cap seems constrained by the cap and plenum thread, but that is allowing it to turn too far causing the misalignment. What am I doing wrong?
Hello Miguel, our best advice is to call our customer serivce department and have them connect you with our workshop. They can help you with your problem, but the answer is unfortunately too long to answer via text in this manner. You can find the contact info on our website. Hope this helps you with your problem.
Weet iemand hoe je aan de 6 tot 6,5 mm komt zoals beschreven in de video? Na installeren en het volledig indraaien van het oude stukje meet ik 8mm. Dus hoe dit aanpassen als dat stukje er al volledig ingevezen is?
How are you friends, recently I received my rifle mkII power plenum .25 to how many bars should I adjust the regulator to optimize autonomy and precision with 25 grains? thanks for help.
This is not the proper way to assemble it. The part that goes in to the trigger housing needs to be assembled first alone and tightened with the dimple right in between the clamp gap. Otherwise it will never align properly. Sure it will look ok but the barrel insertion and removal will be almost impossible and you will cause permanent damage to the entire parts of the rifle. Thre was an ernest rowe video on how to do it but I think FX has taken it down probably to make more money for the dealers. I tried this method and failed. The Ernest Rowe method worked like a charm the first time.
Thats very professional demo..no missy screws lying on top of the table..full detail instruction one by one..viva Deutsman..
The most clear and easy procedure to disassemble and assemble the new PP. the English language text is great 👍. Thanks
Definitely my favorite series of 'How to Install' videos for the Impact, thanks so much and please keep them coming !!!
Hey buddy..
Good video...
2 things you should say.
1. If the impact is without pressure, it makes sense to set the REC to minimum. With the PP you need less REG pressure.
2. If you secure Hammer Stop with glue or loctite, you should wait until the glue is ready. if you mount the valve spring too early, it is possible that the hammer stop will turn and the dimensions will no longer be correct ...
Greetings Rick
Mooi om eens deze kant van Krale te zien.
Ik ben een paar maanden geleden voor het eerst op jullie nieuwe adres geweest en moet zeggen, een geweldige winkel.
Niet voor niets dat ik als lucht sportschutter, maar ook als voorzitter van onze SV iedereen doorverwijs naar Krale.
Goed materiaal, volop keuze, eerlijke prijzen en eerlijk advies.
Kan alleen maar zeggen, ga zo door.
De groeten van SV Woensel 77.
Bedankt voor uw positieve feedback!
Weet iemand hoe je aan de 6 tot 6,5 mm komt zoals beschreven in de video? Na installeren en het volledig indraaien van het oude stukje meet ik 8mm. Dus hoe dit aanpassen als dat stukje er al volledig ingevezen is?
What a very good clear example of a great video.
I need to watch couple more times before I fit mine.
And could not understand your language (sorry) but sub titles were very clear.
Thank you.
Duidelijk en fijn dat er een goed filmpje op internet staat ! Heb het plenum vorige week succesvol zonder geïnstalleerd, en het viel erg mee ! Heb misschien één puntje, voor het dichtdraaien van het plenum heb de klepstang iets terug uit het klephuis getrokken, zodat deze niet heen en weer word gebogen.
Excellent Teacher and very highly skilled - Thanks for sharing your Knowledge with us.
Excellent video, just fitted my kit following your instructions and it works a treat.
Thank you very much
Excellent demonstration
Only thing I would do differently is not have the valve seated when screwing in the front of the power plenum. It puts stress on the valve rod and the Orings that seal where the valve rod exits the power plenum. The passage through the PP is off set so will put a bending force on the rod. The valve has to be pulled towards the muzzle to install the C1 so it makes no sense to seat it.
Excellent step by step guide
This guys a machine on the Impact, thanks for such an informed video. Now can you get some in stock so I can buy mine please. 👍
That is not the first time you have done that, very professional.
I did not see you put the black plastic hammer spring guide back in, off camera?.
thank you
That's because it's not going in again. This part is not needed anymore. ;)
Nice job! Thank you so much for your video sir.
Is there no more buffer oring ?(C3 bumber) Very nice and helpful Video thanks foe making this.
I would put in a new white delron C3 bumper. The old blue o-ring one wears out easily. I just replaced mine. Very cheap on Ebay.
@@humphreydavids mine white delron C3 bumper just arived I will replace my MkII on this weekend . And I wait for my dealer to order a Power plenum for me.
yea, i think he forgot to put the c3 bumber o-ring.
@@humphreydavids Please can you give me a link? I am just starting to learn.
huw mauh
congratulations, excellent images and detailed step by step upgrade.
Thanks, we aim to please. 😉
@@KraleShooting Three questions: do they have in stock? and there are versions - not original FX - that also consider the modifications to the pellet feeder and the barrel connection ... is there an improvement still pending by FX to improve the greater air flow generated by the plenum? Finally, this original internal plenum of FX is compatible at the same time using it with the external plenum ... as for a larger volume of air? or is it already unnecessary at this level?
thank you very much for the help, greetings
@@marcelogalvez9516 1. This product is currently out of stock. 2. We are not aware of any upcoming updates. 3. It would be possible to install an external plenum but we would not advice to do so as there is not need to do that because the FX Power Plenum already delivers optimum power.
@@KraleShooting thanks for answering. Much success to the store. Greetings from Chile
Is there a break in period if the power plenum is newly changed?
Hello, I am looking for information before dismantling everything 😅 on my impact MK2 I noticed a small leak, I located it at the level between the Wheel and the adjuster?
what part could this come from?
Thanks in advance for the advice.
Excellent video!
Hele goede instructieve video. En erg fijn dat de juiste maten worden gegeven.
Maar toch enkele vragen.
Wanneer de afstand van het uitstekend gedeelte van de hammerseat niet juist is, hammerseat in of uitdraaien tot de juiste lengte? (moet je vlot zijn met die loctite)
Wanneer die afstand tussen de probe en achterkant van het huis niet juist is, aanpassen op het blokje voor?
Lijkt mij bij beide vragen wel nml.
Ik hoop de Power Plenum kit snel binnen te krijgen en kan hem nu zeker goed monteren, er zijn toch wel dingen die fout kunnen gaan zag ik.
Super uitgelegd, hartelijke dank.
Can somebody get this guy a wireless microphone. I cant watch this.
Baie goeie en mooi stap vir stap video !! Dankie !!
Rubber ball 6,35 NBR90 missing on valve adjustment spring 🤔
Dans di neiger is brace brace over dare , don’t forget to tighten di vuuuuuuuulve
Hi, do you sell the orings for the power plenum? I need the white pur oring
Buen vídeo se puede poner el plenun a una crown
HI, which green Loctite should I be using for this please?
Excellent! Thanks!
Mooie uitleg voor de installatie van Plenum, maar groene loctite of bedoel je blauwe loctite als later hammerseat nog los wilt krijgen. ;-)
What happen to the buffer oring and plastic spring guide for the hammer?
Buffer is now a delrin attached to the hammer and the old spring guide is replaced with a new one
Goede video, complimenten!
Krale Schietsport Kun je de FX 2 Impact ook bestellen met .22 Slug Liner 700mm, zwaardere hamer, en Plenum fabieks af al geinstalleerd. Wanneer komt de MK3 uit.
Excelente manutenção é customização au mesmo tempo feis ais duas excelente trabalho like
Hi...the new power plenum kit should include the pur o ring and the normal one..because I didn't find it in my kit?
AHMED A I thought the same as you but I eventually found them already seated in position 👍
Hi, followed this but the alignment of the valve housing at one end and plenum end cap hole at the other is way out, meaning that the valve rod is not straight. Way out, like 130° out. I don't want to tighten the end cap more, and there is nothing to grip on anyway, and if I back it out by unscrewing to align the holes the rod goes through, the cap o-ring seal isn't made and air just rushes out. The alignment of the plenum end cap seems constrained by the cap and plenum thread, but that is allowing it to turn too far causing the misalignment. What am I doing wrong?
Hello Miguel, our best advice is to call our customer serivce department and have them connect you with our workshop. They can help you with your problem, but the answer is unfortunately too long to answer via text in this manner. You can find the contact info on our website. Hope this helps you with your problem.
my mag wont fit when i mesure to 44.4 to 44.7
Weet iemand hoe je aan de 6 tot 6,5 mm komt zoals beschreven in de video? Na installeren en het volledig indraaien van het oude stukje meet ik 8mm. Dus hoe dit aanpassen als dat stukje er al volledig ingevezen is?
How are you friends, recently I received my rifle mkII power plenum .25 to how many bars should I adjust the regulator to optimize autonomy and precision with 25
grains? thanks for help.
You should have put the power wheel to minimum before firing it to empty reg.
this rifle is impact X or impact mk2 ?
Impact X
Siêu phẩm 👍👍👍
This is not the proper way to assemble it. The part that goes in to the trigger housing needs to be assembled first alone and tightened with the dimple right in between the clamp gap. Otherwise it will never align properly. Sure it will look ok but the barrel insertion and removal will be almost impossible and you will cause permanent damage to the entire parts of the rifle. Thre was an ernest rowe video on how to do it but I think FX has taken it down probably to make more money for the dealers. I tried this method and failed. The Ernest Rowe method worked like a charm the first time.
mantap👍👍👍
Roses are red, violets are blue, the title is in English, so the video should be too.
Ban oi cho minh sinh cay sung do nha cam on truoc nhe gui ve viet nam cho minh di
I believe, it is a very good air gun, and, a price ... ok, when you want a "ferrari", you don´t care about the price . . .
WEL GEDAAN
As easy as that 🤣🤣🤣🙄🤔😳
Perfect! Thank you!!!