How to removing fuel line fittings

Поделиться
HTML-код
  • Опубликовано: 27 авг 2024
  • Finely got out to the shop to do some work on the 2011 Colorado LS swap project. I was running new fuel lines from the tank to the engine and decided to show you guys how to remove these quick connect fuel line fittings.
    Thanks for watching!
    Stay Safe!

Комментарии • 23

  • @heelspurs
    @heelspurs Год назад +1

    I'm glad to see this video and his replies to those saying "just push the two tabs". Unless your fingers are really tough (not flexible tissue on your finger tips) *and* skinny I don't see how people make it look so easy to squeeze the tabs (like they do in many videos). Another video shows putting a small nut on each end of skinny needle nose pliers for the squeezing.

    • @budslife
      @budslife  Год назад

      You are so right. Those little tabs can be so hard to push in. Especially when you live in Canada, where you get a lot of snow and dirt up underneath your car. It can be almost impossible to push those little tabs in. This is a much easier way using this tool. Thanks for watching!

    • @heelspurs
      @heelspurs Год назад

      @@budslifeI broke the internal plastic tab by squeezing with the needle nose pliers so the connector is not very secure in staying connected ... big problem. Can I pry off the nylon tubing after *carefully* applying heat gun to get thequick connect off? I see videos having to use a clamping method just to push the connector onto the nylon tube so I'm afraid pulling off is an even bigger hassle...i might have to replace the whole line.

  • @CRXSLY
    @CRXSLY 3 года назад +2

    you just have to push the grey tab on those connector....you need the tool just for those close to the intake manifoil! ;o) thx for your great video..gonna help a lot in my Canyon project ;o)

  • @markmcdaniel7766
    @markmcdaniel7766 Год назад

    Do you have any videos/tips on how to change the whole fitting to the plastic/abs fuel line. Typically found on Fords?

  • @user-mj4xp7wi3p
    @user-mj4xp7wi3p 4 месяца назад

    I was watching interested to kniw how you git the fitting back on that plastic tube line

    • @budslife
      @budslife  4 месяца назад

      They usually just snap back together if you didn't destroy the fitting taking it apart.

    • @user-mj4xp7wi3p
      @user-mj4xp7wi3p 4 месяца назад

      Sorry i meant the fuel line , ive got this set up on my van and the fuel line no way would let 1 out and back in. I could cut one out the line but id not get 1 back in.

    • @budslife
      @budslife  4 месяца назад

      They usually snap back in if they don't. That usually means you've damaged a little clip inside the fitting, and you'll need to replace the whole fitting. That can be tricky, but it can be done. I'm pretty sure there are videos on youtube on how to replace these plastic fittings.

    • @user-mj4xp7wi3p
      @user-mj4xp7wi3p 4 месяца назад

      @@budslife its not the fitting id struggle with. Its getting a new fitting put into the original fuel hose. Ive had to replace the hose.

    • @budslife
      @budslife  4 месяца назад

      @user-mj4xp7wi3p try this video it might help you.
      ruclips.net/video/mT8Sne0q_2g/видео.htmlsi=fIsdv_rx7Dk8X6LI

  • @alexturner3493
    @alexturner3493 Год назад

    Do you have a link to the tool? I've taken it apart without the tool one time. One too many. Dirt builds up in there and I needed to work it with a pick.

    • @budslife
      @budslife  Год назад

      I will try and find a link to the tool. But I got this one at Canadian Tire.

  • @chumbucket1313
    @chumbucket1313 Год назад +2

    I call them pain in the ass garbage that causes me grief!

  • @HotOneRecordz
    @HotOneRecordz Год назад

    Pushing in the buttons is much easier. Lol

    • @budslife
      @budslife  Год назад

      Yeah, you would think!

  • @billquillin1952
    @billquillin1952 2 года назад

    How do you get them off if you don't have the tool?

    • @budslife
      @budslife  2 года назад +2

      There's two tabs on the end of these types of fittings that you can squeeze together. Sometimes this will work and they will pop right off but I have seen a lot of times where these tabs will not move they're seized in there so I usually just use the tool and it makes it a lot easier.

  • @jasonmorris5565
    @jasonmorris5565 10 месяцев назад

    Wow. So I’ve been doing it wrong the whole time😂😂😂

    • @budslife
      @budslife  10 месяцев назад

      No I never said anybody was doing it wrong. It's just up here in Canada, where we get lots of snow and salt on our roads, these little clips on these fittings tend to break, and no matter how hard you squeeze them, they will not come apart. This video just simply shows another way to do it, that's all.

  • @rayraysmoove4823
    @rayraysmoove4823 Год назад

    👍🏿

  • @cadillacblueband
    @cadillacblueband Год назад

    Yeah those look easy lol

  • @lwh7301
    @lwh7301 2 года назад

    Dang. You talk like you are on tranquilizers.