I do a comparison of the short and tall seat for the 450MT. I also show you my 3d printed solution to the seat rubbers that fall off on both of these seats.
Yep. Took the bike for a ride with Steves_ADV and put the bike through its paces and the 3d printed pads looked brand new, but dusty where the seat doesn't press them.
Fantastic video outie you are very clever. I know mine are missing like yours, probably first time I put it back on. High seat definitely looks more comfy . Cheers Bazz.
Yep it is really good for height and extra padding for bumps. Sounds like you could do with a set of the 3d printed pads. If you want, message me on Instagram or email your postal address and I'll send a set out for you to test.
great video, thanks again for an amazing solution. what is your opinion about a customizing the normal seat and make it higher and not buying the higher one?
For me the first thing was butt comfort than seat height. The taller seat is also flatter so I can move back n forward on it. With my lower seat I did find it easy to slide up to the tank end but did not check if the front rubber caps are missing. The taller seat is a bit tougher to slide towards the tank end and I have now glued the rubber mounts to the seat. I like the 3D printer idea and have been interested in getting one and using it to print various little parts that are not easy to get or replace. I have been looking at bar raisers too. Not to raise them much but to try and move them forward a bit. I have already rolled them forward/upwards like I have on my enduro bike. It seems like everything I have thought of and been looking at doing,you have already dpne them or had similar ideas. Thanks.
Yeah it is handy having a 3d printer. I use tinkercad to make things as it's relatively easy to use. It's just a website so it's pretty basic but good enough for simple designs. I just put the bar raisers on and they are excellent.
Great video but i think it's always better to mention your inside leg length when refering to seat height as we all have different body sizes also, cheers and well done.
I thought about putting the design up for free but decided to print and sell them so I can put the small profits from each one aside to buy upgraded camera and audio gear for the channel.
Yes that should work, but a lot of people don't realise until it's too late and they have gone. Ironically having learned this when I got home with the tall seat on (dealer installed it for me during the 1000km service) I was going to do just that. But when I took the seat off they were already missing. Probably on the dealerships floor or fell out of the bike and onto the road if they were still bouncing around the battery bay.
maaaate, your 'vlog' is exceptional and i for one appreciate the 'flaws' being addressed from a fellow tall man's perspective; looks like i will add another inch (25mm) to my seat foam; hopefully there's enough cover material so that i can undo it and re-use it; if not, well it wouldn't be the first time i've needed to re-cover a bike seat.... i was thinking of your solution for the seat rubbers as soon as i realised (discovered) what the seat rubbers contact with; my immediate thought was to take the seat rubbers from the base and simply add them to the frame instead but your design is much better; to add to this 'mod', if i may make a suggestion: it would be beneficial to fill the hole where the original rubbers sit in the seat and i would (will) glue your new parts to the frame; a good contact cement should do the trick; did you make sure to re-glue all the other seat base rubbers while you're at it?....again, i would (will) when i get my 450MT; hopefully by the end of this month if the dealer is to be taken on his word; Question: do you take 'custom' work requests with your 3d printer by any chance?; i have a little project i am working on that would benefit from 3D printed parts; i just need someone i can trust to do the job; i have already made prototypes that i can send to you. Cheers!
Where the holes in the frame are, is not where the seat rubbers contact. They contact about 1.5cm towards the front of the bike, so if you do glue the seat ones in, I'd suggest glueing to the seat. The 3d printed ones fit nice and firmly and physically cannot come out when the seat is on as they are held in place by the seat as well as the lug part that goes into the hole. What is it that you're prototyping?
@@outie555 ah ok.....it's hard to know the exact situation re the frame/base rubber contact point without having seen it in the flesh; did you remove the front rubbers from the new seat? are you going to make your new 3D printed to sell? if so, i'd like a pair please; i am prototyping slot car parts; i small matchbox car size chassis and one scalextric size chassis so far with more to follow.
Depends what you mean. Obviously the high seat has a grey centre piece rather than the black of the stock. It also comes two different versions where the only difference is the colour of the little stripe on the side. Yellow or pink to match the bikes colour choice.
Great skills in 3D Printing Outie! Is there a groove cutout in the sheet metal to lock the parts in or have you printed it to be the thickness of the sheet metal tabs? I wonder if they can simply be rectangular in profile & have a wider groove tang (or 2) to squeeze in? The 870mm seat can be set to 850mm by using the lowest link in the rear shock arm🤔
The metal part has a hole in them already, probably so the same part can be used in other bikes in the cfmoto range. The 3d printed pads have a lug that just pops into them for a firm fit.
Hi, i'm exactly the same height. Waiting for my tall seat also to be delivered. In your opinion, what would be the ideal windscreen height to change to?
Honda put a lot of work into placement, number and material of these (sometimes having different material/density at eaxh end etc). They test various set ups on each new bike they design. It's all down to comfort and reducing noise and vibration. I get the feeling this level of detail isn't as strong with the Chinese bikes?
mate - how much is the taller seat in Oz ? Am gonna need one too. Our dealer here had no clue they existed when I ordered my bike - they chased the country importer - who also has no clue :(
I didn't have time to pose for a thumbnail so took a screenshot from the video. But I wasn't smiling so I had 39 seconds to edit it as my toddler was having a melt down and needed attending. Otherwise I would have released the video 24hrs later, once I had a chance to make a decent thumbnail.
Авто/Мото
![Gunna - back in the a [Official Video]](http://i.ytimg.com/vi/oBrbejOHjLw/mqdefault.jpg)
Waiting on my 450MT for a couple weeks now and watching your videos has been relaxing
Definitely less knee bend. You present your video's well. Thanks
Thank you. I'm no professional but I do put a lot of time and effort into it. It's great it's noticed 😄
If you keep doing what you are doing, I predict your channel will blow up ☝
Great plug design. Can you put it on Thing-i-verse for the masses. Thank u.
Great stuff Outie, I finally get to ride a 450MT at a demo day in Denver CO in July.
That's awesome! I bet you're counting the days down!
Excellent and effective solution
Glad you think so!
Very good Idea Outie if the rubbers problem comes up at the dealer I goto I can say I can get a solution!
Yep. Took the bike for a ride with Steves_ADV and put the bike through its paces and the 3d printed pads looked brand new, but dusty where the seat doesn't press them.
Quick, patent that seat rubber clip design, could be a profitable side hustle. Great detective work! 😅
Probably would be.
Definitely, make that available online and some of us here will buy it!
You’re still a funny bloke & appreciate your content 🤙
Thanks Steve
The tall seat just looks proper 👍🏻
Great solution Mate, well done.
Very nice and thorough presentation. Thanks !
Glad it was helpful!
Please can you share the CAD files for your design outie? It could help tremendously.
+1000000 pleaseee
Fantastic video outie you are very clever. I know mine are missing like yours, probably first time I put it back on. High seat definitely looks more comfy . Cheers Bazz.
Yep it is really good for height and extra padding for bumps. Sounds like you could do with a set of the 3d printed pads. If you want, message me on Instagram or email your postal address and I'll send a set out for you to test.
@outie555 Thanks mate that would be awsome.
Clever little design 👍. Gotta say that high seat is super comfortable compared to the Tenere.
It's a new seat so only time will tell once it wears in, but t so far so good
Great video
Glad you enjoyed it
Awesome, I'm 6'1 tall as well 😜
great video, thanks again for an amazing solution. what is your opinion about a customizing the normal seat and make it higher and not buying the higher one?
Excelente content …. 🤙🏽
What a blow to see already rubbers coming out of a brand new bike.
Gen 1 so not surprised but a really simple fix.
I would love to have a look at the STL. Have you uploaded it anywhere?
For me the first thing was butt comfort than seat height. The taller seat is also flatter so I can move back n forward on it.
With my lower seat I did find it easy to slide up to the tank end but did not check if the front rubber caps are missing. The taller seat is a bit tougher to slide towards the tank end and I have now glued the rubber mounts to the seat.
I like the 3D printer idea and have been interested in getting one and using it to print various little parts that are not easy to get or replace.
I have been looking at bar raisers too. Not to raise them much but to try and move them forward a bit. I have already rolled them forward/upwards like I have on my enduro bike.
It seems like everything I have thought of and been looking at doing,you have already dpne them or had similar ideas. Thanks.
Yeah it is handy having a 3d printer. I use tinkercad to make things as it's relatively easy to use. It's just a website so it's pretty basic but good enough for simple designs. I just put the bar raisers on and they are excellent.
great video, do you know your inside leg measurement?
Great video but i think it's always better to mention your inside leg length when refering to seat height as we all have different body sizes also, cheers and well done.
Good tip! No idea what my inseam is so I'll make note to mention it when I measure it.
And a business is born, or you could share the file to the world
I thought about putting the design up for free but decided to print and sell them so I can put the small profits from each one aside to buy upgraded camera and audio gear for the channel.
Or, you could just put a spot of glue inside the rubbers?
Yes that should work, but a lot of people don't realise until it's too late and they have gone. Ironically having learned this when I got home with the tall seat on (dealer installed it for me during the 1000km service) I was going to do just that. But when I took the seat off they were already missing. Probably on the dealerships floor or fell out of the bike and onto the road if they were still bouncing around the battery bay.
maaaate, your 'vlog' is exceptional and i for one appreciate the 'flaws' being addressed from a fellow tall man's perspective; looks like i will add another inch (25mm) to my seat foam; hopefully there's enough cover material so that i can undo it and re-use it; if not, well it wouldn't be the first time i've needed to re-cover a bike seat....
i was thinking of your solution for the seat rubbers as soon as i realised (discovered) what the seat rubbers contact with; my immediate thought was to take the seat rubbers from the base and simply add them to the frame instead but your design is much better;
to add to this 'mod', if i may make a suggestion: it would be beneficial to fill the hole where the original rubbers sit in the seat and i would (will) glue your new parts to the frame; a good contact cement should do the trick; did you make sure to re-glue all the other seat base rubbers while you're at it?....again, i would (will) when i get my 450MT; hopefully by the end of this month if the dealer is to be taken on his word;
Question: do you take 'custom' work requests with your 3d printer by any chance?; i have a little project i am working on that would benefit from 3D printed parts; i just need someone i can trust to do the job; i have already made prototypes that i can send to you. Cheers!
Where the holes in the frame are, is not where the seat rubbers contact. They contact about 1.5cm towards the front of the bike, so if you do glue the seat ones in, I'd suggest glueing to the seat. The 3d printed ones fit nice and firmly and physically cannot come out when the seat is on as they are held in place by the seat as well as the lug part that goes into the hole. What is it that you're prototyping?
@@outie555 ah ok.....it's hard to know the exact situation re the frame/base rubber contact point without having seen it in the flesh; did you remove the front rubbers from the new seat? are you going to make your new 3D printed to sell? if so, i'd like a pair please;
i am prototyping slot car parts; i small matchbox car size chassis and one scalextric size chassis so far with more to follow.
Great solution... The new seat has other colours?
Not that I have seen
Depends what you mean. Obviously the high seat has a grey centre piece rather than the black of the stock. It also comes two different versions where the only difference is the colour of the little stripe on the side. Yellow or pink to match the bikes colour choice.
@@shamefulmanny4542 would like something more darth vader... DARK!!!
@@mikefreitas1331 Yeah I'd prefer black too but unfortunately it looks like the tall seat only comes with the grey top.
Where can I find those 3d print rubber ? I’m from France
Great skills in 3D Printing Outie! Is there a groove cutout in the sheet metal to lock the parts in or have you printed it to be the thickness of the sheet metal tabs? I wonder if they can simply be rectangular in profile & have a wider groove tang (or 2) to squeeze in?
The 870mm seat can be set to 850mm by using the lowest link in the rear shock arm🤔
The metal part has a hole in them already, probably so the same part can be used in other bikes in the cfmoto range. The 3d printed pads have a lug that just pops into them for a firm fit.
Hi, i'm exactly the same height. Waiting for my tall seat also to be delivered. In your opinion, what would be the ideal windscreen height to change to?
Honda put a lot of work into placement, number and material of these (sometimes having different material/density at eaxh end etc). They test various set ups on each new bike they design. It's all down to comfort and reducing noise and vibration. I get the feeling this level of detail isn't as strong with the Chinese bikes?
Probably not as they are 1/3 cheaper cost compared to Honda. But if it's just those two rubbers that go wrong then it's still good.
thanks for the info! the audio of this video has some high freq artefacts that are audible and not so pleasant for the ear.
Sorry about that, one day I'll get some external mics. I don't hear it as I've got hearing damage.
mate - how much is the taller seat in Oz ? Am gonna need one too. Our dealer here had no clue they existed when I ordered my bike - they chased the country importer - who also has no clue :(
$200aud according to their accessory site.
do u even age adrian>? nice vid... I also look like im in my 20s lol
Not sure if I do, but maybe age a year for every 5 years 🧛🏽 it's good to look young though, stops us buying beer when we leave our IDs at home.
Anyone knows how much is the high seat? I am trying to see if asking a upholster to do the colour i want is better/cheaper or not. Thanks
$200aud according to their accessory site.
@@shamefulmanny4542 thats about 125€. I probably can get it upholster for 75€ in dark grey ou black. Thank you so much
Yo tambien mido 1.85 y me duele bastante la espalda con el asiento de seria :7
what's going on with these thumbails?
I didn't have time to pose for a thumbnail so took a screenshot from the video. But I wasn't smiling so I had 39 seconds to edit it as my toddler was having a melt down and needed attending. Otherwise I would have released the video 24hrs later, once I had a chance to make a decent thumbnail.