Configure Cisco Access Point using GUI Standalone/Autonomous with WPAv2 Authentication Key

#Configure_Cisco_AP #Standalone_GUI #IT_Support_People
IT Support People Facebook Page:
/ it_support-peopledeskt...
Link for Other Related Videos:
Configuring Cisco Router to Access Internet through ISP Home router:
• Connect Cisco Router ...
Configure VLAN | Allow VLANs to Access Internet
• Configure VLAN | Allow...
In this video I've shown step by step process How to Configure Cisco AIRONET 3602i Autonomous/Standalone Access Point using GUI with WPAv2 Authentication Key. I've divided the whole process into two parts which are given below:
Part 1: Accessing Cisco Aironet Access Point GUI Web Interface
• Console the Access Point with Putty (default user name and Password: Cisco)
• Resetting to factory Default Settings Using the MODE Button
• Check IP status and Assign a static IP to BVI1 interface with same subnet mask
• Go to Web Browser and type BVI1 interface IP address (keep user name blank and default Password: Cisco)
Part 2: Configuring Aironet Access Point with WPAv2 Authentication in GUI
1. In Easy Setup
Under Network Configuration
--Edit AP hostname, Static IP, Subnet mask and Default Gateway
Under In Radio Configuration
--Create SSID name WLAN_New under Radio 2.4GHz and select Broadcast SSID in Beacon
2. Apply Encryption Modes to AES CCMP
3. Enable WPAv2 and apply WPA Pre-shared Key: to SSID
4. Enable Wireless Radio Interface (Radio0-802.11N2.4GHz/ Radio1-802.11N5GHz) UP
5. Save the configuration
6. Finally check the SSID Wi-Fi connection, Security Key, IP address and browsing through internet
Cover Topic:
How to configure Cisco AP,
How to Configure Standalone Cisco Access Point,
Configure Cisco AIRONET 3602i Autonomous/Standalone Access Point using GUI,
How to Configure Cisco Standalone/Autonomous Access Point using GUI,
Cisco access point configuration step by step GUI,
How to configure standalone Cisco access point from GUI,
How to Configure a Cisco Wireless Access-Point (AP) from GUI,
How to configure standalone Cisco access point from GUI,
WPAv2 Authentication Key, Encryption AES CCMP,
Cisco AP Wireless Radio Interface Radio0-802.11N2.4GHz/ Radio1-802.11N5GHz,
Create Cisco AP SSID GUI, Enable WPAv2 and WPA Pre-shared Key,
cisco 3602i standalone configuration,
Resetting Cisco AP to factory Default Settings Using the MODE Button,
Cisco IOS Configuration Guide for Autonomous Aironet,
cisco autonomous ap configuration example,
how to access cisco ap web interface,
cisco ios configuration guide for autonomous aironet access points,
Cisco Autonomous Wireless Network - Home style configuration,
Configuring the Access Point for the First Time,
SSID on Autonomous AP Configuration Example,
Cisco Autonomous AP - Initial Setup & Open SSID Creation,
Autonomous AP - Initial Setup & Open SSID Creation,
Using the Web-Browser Interface Cisco Aironet 3600 Series,
SSID on Autonomous AP Configuration Example - Cisco,
how to access cisco ap web interface,
how to configure cisco access point without controller,
How do I assign an IP address to a Cisco access point,
How do I access my Cisco wireless access point,
how to configure cisco wireless access point via console,

[@Aarasstudio]

Your videos are highly appreciable as it is live in physical cisco devices, very useful and highly recommended for cisco learners. Waiting for all complete series. Thank You.

[@itsupportpeople219]

Thanks for watching

[@stephensugandh9035]

Masood bhai you are very clear in what ever you show , and explain. . . I really appreciate it. . . Thank you very much, please keep up you good work. . .

[@MrEDGE1984]

I appreciate you ground work, most people feel expertise in advance thisgs but they lack basic understanding of networking. Ur efforts are worthy of appreciations.. plz upload more such videos.

[@itsupportpeople219]

Thanks for watching...

[@shiabkhan6680]

Proud of you my friend. Searching some video on cisco air ap on youtube and suddenly it pops up to my screen.

[@onrizestar7062]

One of the best video for Cisco AP Really awesome... Thanks for making this video

[@md.mahtabuddin3979]

Good one and very useful for the IT people like me.

[@itsupportpeople219]

Thanks for watching

[@roshanmutha2329]

You explained so nicely man. You showed router and switch physically to understand better. Thankyou. Please teach us more

[@sabretd19]

Brilliant!!! Easy to follow Instruction... 2.4 & 5G working before video conclusion...Thank You

[@itsupportpeople219]

Thank for watching

[@edenorganics6476]

i've really gathered much here, thanks

[@Lyriks_]

I just discovered your channel ! You're a gem, keep doing what you do !

[@itsupportpeople219]

Thanks for watching

[@rider275]

I really enjoyed this video. I have a home lab but no wireless access points. Your video has helped explain how I can add an AP to my lab. Thank you!

[@Hoscorp]

Congratulations, your channel has grow up, very usefull vids. Keep it up. This vid and the reset one i will do.
Thanks for sharing.

[@ARSINDIANVLOGGER]

Nice shearing dear friend 👍

[@chimsopheak-kh]

Wow, it's the best tutorail. You have what I finding. Keep going on brother.

[@ОлексійКлименко-д3ы]

Thanks for your hard work.
Please keep making videos. It is very useful.
Forgive me, but I want to make a couple of comments:
1-Could you balance the sound in your videos? You have to constantly adjust louder\quieter.
2-Could you try to remove the noise?
3-Sometimes it seems like the video is a little too long.

[@itsupportpeople219]

Thanks for watching... Lot appreciated your suggestions

[@grahammccann8554]

Thank you for taking the time to make this video. It was very informative.

[@fred2009ification]

Cool video, man. Keep up the good job.

[@mohamedabdelkader8846]

thanks for the video :)
I have a quick question , can we use power adapter instead of POE injector in case my switch has no POE ?

[@k.j.fatema7865]

Excellent content...very informative and easy to understand...keep it up

[@itsupportpeople219]

Thanks for watching

[@ibrahimsaadansary9840]

Vaia you are too good. i am also working as system support engineer. if possible please make real life virtualization training video. very much needed. and one request please don't lower your quality when you will become famous. may Allah bless you.

[@asifmehmood123]

Thanks for recording this video. This video is very helpful. Much appricated

[@itsupportpeople219]

Thanks for watching...

[@Jagarm]

Thanks for the great video. Thanks to you, I got it all setup, but the speed is slower than my router

[@itsupportpeople219]

Thanks for watching...

[@wildcurve]

Thank you bro for the information

[@sherrillboyce7189]

Thanks! For home network, do you recommend a CISCO ASA FW to CISCO Router to Cisco Switch to VLANs for Cisco Aironet and other devices?

[@itsupportpeople219]

Thanks for watching...I reckon Cisco ASA 5505 Firewall is well enough for home network

[@mhabibtmc6399]

you well explained i would like to say thank you for this. Appreciated !!!!!

[@gugulethumoyo6284]

This is very helpful. Its practical

[@martinsenechal5379]

Great video,realy helpfull.
Can you tell us how to set both 2.4 and 5ghz with the same ssid
Thanks

[@itsupportpeople219]

Thanks for watching.. You can add 5GHz radio interface similarly like how I did for 2.4 GHz

[@amirahmed1404]

Very good explanation. Thanks you.

[@abhinavsingh9957]

Thanks for Information 🔥

[@itsupportpeople219]

Thanks for watching

[@villagedotvibes]

Thank you so much for this video. Your content is importent for real life support. Please make a video with OSPF and EIGRP routing configuration

[@itsupportpeople219]

Thanks for watching

[@pramilasingh2726]

explained everything in detail

[@itsupportpeople219]

Thanks for watching

[@rodrigosebben1084]

Thank you so much! this video help me to configure the ap.

[@luisfelipecosta9664]

Thank's , from Berazil.

[@omg2026]

Thank you sir for another great video!

[@itsupportpeople219]

Thanks for watching

[@LoveHWH]

Hello Bro, Just got a question. If I have another APs, so all the configurations will be the same in this case? Thanks

[@rashiniperera7000]

thank you so much for this content

[@NewsBroadcasting]

Good video , is it possible to use AIR-CAP27021-A-K9 as standalone?

[@chiarenwar7139]

Have same question ....

[@lkdipeolu]

Very Good. I love it. Do you have the lightweight version?

[@rasailiofficial9885]

Ok thank for infomisson sir

[@itsupportpeople219]

Thanks for watching

[@yamguerra-d3e]

thank you for your video it helps me a lot

[@mauricionava1976]

Thanks for the video!!

[@ajmusicpak3238]

nice yaar

[@himanshuyadav3380]

Bhai you have made awesome video can you make video on AP light version which will configure by wlc.

[@itsupportpeople219]

Thanks for watching

[@MahananGogoi]

Great tutorial. Thank you!

[@itsupportpeople219]

Thanks for watching...

[@jeffersoncafegarcia8215]

Good video 📸😊

[@itsupportpeople219]

Thanks for watching

[@narender1199]

So Super Sir ji

[@hoanggeneral]

@IT Support People,
I was able to get all the way and completed the set the BVI to a static IP (manual). However, when I tried to access the GUI interface in the web browser, the base just won't load.
Any clue on how to over come this?

[@TypeOneGuy03]

same

[@TrungTuyenLam]

Do you know? The GUI interface is just used for the standalone IOS version of this Cisco AP.

[@leaguebdd2053]

It really helps a lot about the Cisco AP !

[@itsupportpeople219]

Thanks for watching

[@phantran3718]

We have two band 2.4 and 5 on the Aironet. Can you make a clip how can we make them online with one SSID only. I have two aironet, is it possible to run seamless SSID in autonomous.

[@richardm7502]

Thanks for this video it's for sure helpful,, and how can I configure my Cisco AP has this version AP3G2-K9W8-M?

[@garyhedberg4318]

Will this process work with a Cisco Aironet 2602I-A-K9? I don't have PoIP but I do have an external 48vdc power supply. Would there be a firmware update that needs to be applied first? I'm just a home user. Overkill probably but I picked up 75 of these access points at a very reasonable price.

[@sadamsta5302]

Good job 👍

[@MuhammadAli-od7hd]

Oooo lovely

[@itsupportpeople219]

Thanks for watching

[@MineGamer153]

Hello, I want to ask what type of rollover cable you are using. I just bought USB-RJ45 type but I cannot connect to my LAp1142n. With WLC it works just fine. I tried different baudrate but still not working.. Thanks for any answers

[@tanmaymukherjee502]

Excellent

[@itsupportpeople219]

Thanks for watching

[@SuburbanSwadh]

Very nice 👍👌

[@itsupportpeople219]

Thanks for watching

[@danicanilbertvlog8042]

Good you're content

[@itsupportpeople219]

Thanks for watching

[@appelwoin76]

Have you confiured a dhcp server for the client IP`s and where ? When I configure 6 Standalone APs, can i configure the same SSID on every AP`?

[@PiotrWisniewski-cy2sd]

Hi. Is it possible to use Cisco 9105 awx in home instalation?
I've got 3 pcs of that AP, and i cannot do anything with that:(
Thanks for your answer.

[@mohammadshahfaisal427]

Suppose I don't have a console cable, can i configure direct access point

[@yourictmyedu5783]

Thanks

[@owaisraja5325]

Very nice

[@PatrickGuerrisi]

when I try to make my ssid I get the following "encryption already exists in interface, enable vlan"

[@Adnankhan-rx6xo]

Well done

[@itsupportpeople219]

Thanks for watching

[@RajaRaja-sc2xb]

Thank you sir

[@makmalbalouch7810]

Nice

[@itsupportpeople219]

Thanks for watching

[@mimegajet6346]

nice content

[@shiva___pavi]

bro thank you so much

[@itsupportpeople219]

Thanks for watching

[@Fun--knowledge]

good and samble

[@wajahatullah3626]

Hi Masood, I've configured the Cisco AIR-LAP1042N-N-K9 through static IP and also added the radio 2.4 & 5 GHz & enabled in network interface but still I haven't found the Wlan in my WIFI list. The AP is showing green light instead of blue, it's mean that no one is connected through this AP. Can you please tell me what to do to make ensure that WIFI is working.?

[@itsupportpeople219]

Thanks for watching...
Make sure you selected the option "Broadcast SSID in Beacon" in the Radio Configuration area.
You can try under SSID Configuration "mbssid guest-mode" instead of "guest-mode"
Thanks

[@rkbusiness5952]

Very nice beautiful😍 😊 ❤

[@davidnagapn6075]

Great videos, I am looking for the autonomous firmware for a AIr-CAP3702i-A-K9. If no one has it, do you know where I can get it? I can't download from Cisco.

[@ratechunlimited]

Thats great

[@itsupportpeople219]

Thanks for watching

[@ironmen9983]

Hi, could you please have a video for Cisco VOIP configurations. Thanks

[@ahmetgure1506]

Thanks for video,
When i press apply 19:21 it says; *WPA requires 'network eap' or 'open authentication' with eap or 'open authentication' with 'wpa pre-shared key'.
How can i solve this problem?

[@PatrickGuerrisi]

Man I set this up ages and I am tryin gto disable it. When get into the
Network Interfaces: Radio1-802.11AC5GHz Settings settings. I click disable next to ( enable radio ) and it just goes back to enable automatically'? I cannot disable it

[@silaskalonzoke3038]

Nyc 🥰

[@KHANQTR81]

i am trying to download ios image for " Cisco Aironet 1140 Series Access Point"
but can't. will u help me please. thanks

[@Vandelroy1]

thank you for your video! But it does not work for me, I check my config with your multiple times, but it is the same. If I try to connect with my Windows 10 Client, I get directly the message that no connection is possible with the network, also I get no field to type the password. If i change to open Wifi with no cipher the connection works. Can you help me?

[@taimoorsaleem8080]

Dear please tell me how to configure AIR-CAP2702l-E-K9 cisco access point setting. I try but it's configuration not display.

[@MuhammadAli-rf2jo]

goood

[@itsupportpeople219]

Thanks for watching

[@ervindarya]

would this work with Cisco Aironet 2702I AIR-AP2702I-UXK9 IEEE 802.11ac 1.32 Gbps Wireless Access Point also?

[@monkeybluesMMA]

do we need a switch to enable and connect to a cisco access point?

[@Tommy-oj4hd]

I only see: GigabitEthernet0 interface, can't see anything else like Radio or BVI1. I am running: "C3500 Software (AP3G1-RCVK9W8-M)" any ideas?

[@pernord26]

can you do a video with Cisco Mobility Express

[@md.jobaerf7248]

Which country are you from brother

[@riyas2khan]

hi bro, can we setup guest access with limited time access ?

[@alexanderamores1760]

Good bro,..please make another video of Cisco Voip PHONE connected to Cisco switch., thank you.

[@itsupportpeople219]

Thanks for watching...

[@leading4Him]

Skip to 4:00 if you actually came here to see how to setup the AP.

[@firmanprtama]

Hello,
How many SSID does this access point support?

[@CorNiger]

I think support two one in 2.4ghz and other in 5ghz

[@lucksin]

Bro, Good Video, however when i setup 5ghz, the clients are getting disconnected every 2 seconds. I have tried resetting the hardware and its the same. Any help would be appriciated. 2.4Ghz works fine.

[@lucksin]

I checked the logs and it says "Interface Dot11Radio1, Deauthenticating Station 748f.3cbf.xxxx Reason: Previous authentication no longer valid"

[@itsupportpeople219]

Thanks for watching... If 5 GHz doesn't work on GUI then you can try CLI. You can try the following video
ruclips.net/video/JkUfTXuwj2U/видео.html

[@argenisvalero8461]

Buenas amigo una consulta tengo este asepoint cisco aironet 1252ag ak9 nesecito orientacion ya que me llego uno y quiero saber si la consola de trabajo es la misama para el reseteo que sotwere nesecito y si el proceso es el mismo en este modelo con referencia del video publicado

[@yuprulesing]

You should put the model # of the Access point in the title so people can find the video more easily.

[@itsupportpeople219]

Thanks for watching

[@animalsvideosalltypes.6005]

good

[@dennisdoubek4329]

I have a problem, every time I want to access my access point "ap:" is displayed in Putty, but in your video "ap.home.>" every command I enter is played with unknown CMD. what am I doing wrong?

[@SamMehnaz]

I have the same issue! Did you figure it out?

[@trujillobb]

@@SamMehnaz maybe put command "ena" as enable then the password.

[@opendebate]

Please make a video to upgrade the firmware from GUI

[@irineuromanato]

Hi
Please do you have informations about ap2802i-z-k9 to convert to standalone. This is a equip that I´m using in my lab. I cant find the right image to apply.

[@leonpetterson219]

Hi Irineu.... Wondering if you were able to setup your device

[@fahimuddinsafi9958]

Hi Sir,
Can access the AP from Browser cannot make any changes to it through GUI says 404 not found
any solution please
thank you,

[@MrMARIF786]

Hello Dear i hv cisco air ap2802i-e-l9c there is wireless option setting is disable in web console i can't add multiple Ap in on console ...plz u can help me about this there is some command in CLI mode to activate wireless setting. if u more information i can send u screenshot. thank u

[@PPL9420]

Plz tell for wlc and Ap different network in possible