I did this on my old laminate countertop and it turned out soooo beautifully. Has depth and complexity too. Thank you! Btw, I recommend using a hair net to prevent hair from falling in!
I just did this on a wooden dresser that will be used as a bathroom vanity. It's still drying but right now it looks awesome. Just a tip for anyone using the kit on bare wood - apply a coat of Kilz stain-blocking primer first! I used 4 coats of the Giani primer, which covered the bare wood wonderfully, but when I spritzed the water on the veining paint, I was getting brownish puddles, which I assume was from the wood. I dabbed them up with a paper towel, but "I" can still tell they're there. Using the white highlighting paint helped cover some of the brownish areas. All-in-all, I'm happy with the way it turned out, except now I want to make everything look like marble. LOL
I did mine yesterday, super easy, I did the black which is much easier. The veins are sprayed on with white silly string type material I could have completed the entire process in an hour, it takes longer to tape than it does to apply product
Ok so how on earth did you only end up with two spots of white paint on your fingers. How many clean black T Shirts did you go through whilst filming the application of the primer?
Unfortunately this will be tricky! We recommend securing tarps with as much tape as you can, leaving no gaps for the epoxy to get through. It can also be helpful to create dams as mentioned below!
Hello, I want the exact kit that you are showing. However, I prefer my veins/marble effect to be black instead of gray. What do I do or purchase to create black veins?
The countertop and backsplash are the same formica, with a silver edge between them. Would I use the same technique on both? Would I tape off the silver edge? It's skinny, skinnier than the painters' tape.
Hello, can this work on an existing marble countertop including the wash basin? If so, can you share the instructions if different than this video, please?
Hello! You can apply the epoxy on a surface that has slight texture as long as you use enough product. If the epoxy is spread too thin, the texture will show through.
I just did this kit on my countertops. My originals were a dark green color, so it took 4 coats of primer. Turned out nice. Only thing is, trying to keep lint/fuzzes/hairs out of the epoxy while it’s curing is IMPOSSIBLE. Only thing that sucks about this.
@@RichieMain I have a charcoal lab, and honestly I didn’t get many dog hairs in it at all. Mostly just fuzzes and fibers from the air flow. It’s a bitch when it’s almost dried and you find some fuzzes or hairs that need pulled out 😫
@@TonyP-ft1tu Thx for the reply Tony. Have a lab too but also. Bernese Mtn Dog and 2 cats. lol. Have been painting cabinets and pet hair has been a challenge. I do like this method though because epoxy is just the final step.
@@RichieMain no problem! It turned out great and has been holding up nicely. Decided to give it a try before we decide to fully replace our countertops in a few years.
@@TonyP-ft1tu @RichieMain I'm sorry to hear this! If you have some texture from debris, we have a buffing technique that can help. Please reach out to info@gianigranite.com
We wanted to demonstrate a softer more natural marbling pattern. Unfortunately, it is harder to pick up on camera. You can check out our instagram for different marble applications and inspiration!
I wish you would have exaggerated the marble veining a bit more. I could hardly see it. Maybe consider an upcoming tutorial on how to make dimensional veins.
I did this on my old laminate countertop and it turned out soooo beautifully. Has depth and complexity too. Thank you! Btw, I recommend using a hair net to prevent hair from falling in!
How is it holding up after 3 months?
Have you had any issues with the epoxy yellowing?
Lynne ours have started to yellow three years in
I just did this on a wooden dresser that will be used as a bathroom vanity. It's still drying but right now it looks awesome. Just a tip for anyone using the kit on bare wood - apply a coat of Kilz stain-blocking primer first! I used 4 coats of the Giani primer, which covered the bare wood wonderfully, but when I spritzed the water on the veining paint, I was getting brownish puddles, which I assume was from the wood. I dabbed them up with a paper towel, but "I" can still tell they're there. Using the white highlighting paint helped cover some of the brownish areas. All-in-all, I'm happy with the way it turned out, except now I want to make everything look like marble. LOL
I did mine yesterday, super easy, I did the black which is much easier. The veins are sprayed on with white silly string type material I could have completed the entire process in an hour, it takes longer to tape than it does to apply product
Thank you so much! I enjoyed your video. I am about to do this exact process and Im so nervous! You make it look easy. I hope it is!
amazing work.
Ok so how on earth did you only end up with two spots of white paint on your fingers. How many clean black T Shirts did you go through whilst filming the application of the primer?
Can I apply a second coat of the prtecting clear coating after the first coat dries?
Can we use polyuethane or any other clear coat on top of the epoxy for added protection? If yes, do you have any recommendations?
Can you just wet the brush to do the veins instead of spaying water?
Do you have to use the marbling? Or can i just use the white epoxy for a plain white look?
We have a White Glass kit that will give you a solid white look! It is a simple two-step kit with white primer and epoxy!
Can you add two coats of epoxy for a stronger finish?
You can if you would like but it is not necessary! When applied correctly, one layer of our epoxy is extremely durable!
@@GianiGranitehow long does the epoxy last ? Few years ? Does it chip easily?
Does the epoxy yellow?
We did ours three years again and we are seeing some slight yellowing in corners
How does the epoxy hold-up against yellowing?
Ours has started to slightly yellow in corners about three years out
@alexarihani2902 I ended up going with Savage Patriots' PolyKote , and am so relieved I did. It's a hybrid product, so it's non-yellowing.
I’ll look into that rec if we opt to go this route again
I have 40 sq ft of countertop in my kitchen. How much do I need to purchase?
Please email info@gianigranite.com for assistance with your measurements!
Bonjour est ce que vous livrez en France merci
What if my countertops are flush with the top of the cabinetry? How can I stop the epoxy from running over the edge of the counters?
That sounds tough. I would use a lot of painters tape and tarps
You’re S.O.L. Lol
Create a tape damn and cover everything well
Try to add a 1x2 on the edge
Unfortunately this will be tricky! We recommend securing tarps with as much tape as you can, leaving no gaps for the epoxy to get through. It can also be helpful to create dams as mentioned below!
So my countertop is already yellow. What should I do?
Did you use this kit and it yellowed??
Hello. I have a question. Can this product be used on an existing granite countertop? Thanks.
Hello! Our countertop kits can be used on granite counters. It requires additional prep, but we can provide you with the proper instructions!
@@GianiGranitecan you probide me with the additional instructions?
@@anniebell9961 Please reach out to our customer service for the instructions! You can reach them at info@gianigranite.com
My old countertop has metal edgings,would the paint adhere to metal sidings too?
Please reach out to info@gianigranite.com for assistance!
Hello, I want the exact kit that you are showing. However, I prefer my veins/marble effect to be black instead of gray. What do I do or purchase to create black veins?
Please reach out to our customer service email: info@gianigranite.com. They will help you find the right items!
Will this work on my pink salmon laminate countertop?
Absolutely!
I just finished doing this on my countertops and parts of it came out pitted....whats the best way to fix that?
I'm sorry to hear this! Please email info@gianigranite.com for instructions on how to correct this.
Will the empty-ish cans spontaneously combust if left open on the floor overnight?
We provide proper disposal instructions with the kit to help our customers avoid any hazards!
Will this adhere to a painted countertop?
It will! Just sand with #600 before prep work to promote adhesion.
The countertop and backsplash are the same formica, with a silver edge between them. Would I use the same technique on both? Would I tape off the silver edge? It's skinny, skinnier than the painters' tape.
Please reach out to info@gianigranite.com for assistance!
Hi can this be used on a marble floor?
Unfortunately, we cannot recommend applying our kits on flooring!
Can I do this on a piece of MDF?
You can, just be sure to prime! We include detailed instructions on our website and in the kits!
Hello, can this work on an existing marble countertop including the wash basin? If so, can you share the instructions if different than this video, please?
Hello! We do have instructions for this! Please reach out to our customer service at info@gianigranite.com
Can you do this on a textured formica counter that isn't smooth.
Same question
Hello! You can apply the epoxy on a surface that has slight texture as long as you use enough product. If the epoxy is spread too thin, the texture will show through.
Do you and the counter if it's granite
Hello! Our countertop kits can be used on granite counters. It requires additional prep, but we can provide you with the proper instructions!
Wow!
I just did this kit on my countertops. My originals were a dark green color, so it took 4 coats of primer. Turned out nice. Only thing is, trying to keep lint/fuzzes/hairs out of the epoxy while it’s curing is IMPOSSIBLE. Only thing that sucks about this.
I'm worried about dog hair!
@@RichieMain I have a charcoal lab, and honestly I didn’t get many dog hairs in it at all. Mostly just fuzzes and fibers from the air flow. It’s a bitch when it’s almost dried and you find some fuzzes or hairs that need pulled out 😫
@@TonyP-ft1tu Thx for the reply Tony. Have a lab too but also. Bernese Mtn Dog and 2 cats. lol. Have been painting cabinets and pet hair has been a challenge. I do like this method though because epoxy is just the final step.
@@RichieMain no problem! It turned out great and has been holding up nicely. Decided to give it a try before we decide to fully replace our countertops in a few years.
@@TonyP-ft1tu @RichieMain I'm sorry to hear this! If you have some texture from debris, we have a buffing technique that can help. Please reach out to info@gianigranite.com
How much?
Got mine on Amazon for $199
Our epoxy kits range from $114 - $199 on our website and Amazon!
You hardly have any Marble looking paint on there at all!!!! Did you not want that?!
We wanted to demonstrate a softer more natural marbling pattern. Unfortunately, it is harder to pick up on camera. You can check out our instagram for different marble applications and inspiration!
I wish you would have exaggerated the marble veining a bit more. I could hardly see it. Maybe consider an upcoming tutorial on how to make dimensional veins.
Can i also use the montana marble spray on top of the paint as well before applying the epoxy?
You can!
@@GianiGranite Thank you!