Changing the Light Bulb in an Above Ground Pool | Aqualuminator
HTML-код
- Опубликовано: 22 май 2024
- In this video, Mark goes over how to replace the bulb for your above ground aqualuminator light made by Pentair.
⏩ HAVE A QUESTION FOR MARK? ⏪
If you have a question you'd like answered or would like to book a 1 on 1 phone session with Mark, then consider checking out our Patreon page!
/ hallmarkpoolsupplies
Visit hallmarkpoolsupplies.com for all your pool supplies, and needs
Like us on Facebook: / hallmark-pool-supplies...
Video Timestamps
00:00 - Intro
00:38 - Disconnecting power
01:43 - Removing the old light
02:56 - Installing the new light
03:44 - Rewiring the light
Changing the bulb in your in-ground swimming pool light: • Changing the Light Bul...
Need any parts for your aqualuminator? Check out these links below!
Video Links:
Complete Light: hallmarkpoolsupplies.com/p-10...
Light Bulb: hallmarkpoolsupplies.com/p-10...
Bulb O-ring: hallmarkpoolsupplies.com/p-10...
Flow Director: hallmarkpoolsupplies.com/p-10...
Threaded Wall Flange: hallmarkpoolsupplies.com/p-10...
Wall Gasket: hallmarkpoolsupplies.com/p-10...
Convertible Fitting Body: hallmarkpoolsupplies.com/p-10...
AQUALUMINATOR Nut: hallmarkpoolsupplies.com/p-11...
Music: zachs_tape
Thank you
Thanks for the video. Is it possible to replace the bulb with an LED version? And if yes, do you have a suggestion or a link to order?
The Aqualuminator light is only made one way.
When installing the light should you be able to turn the body on the outside of the pool or does that mean it's not tight enough
If you can turn the body on the outside it’s not tight enough, try tightening a little more but do not over tighten. You also want to make sure that your gaskets are in place as well. Thanks for watching.
How do I replace a light return with a non light return? I’m concerned about the liner pulling away or the new return not sealing well. Thanks.
The Aqualuminator light and the return cut out on your pool use the same size opening, you can switch from one to another. If you have any questions feel free to contact me, I will be glad to help.
@@HallmarkPoolSupplies thanks. So any danger in having the liner pull away from the hole when I swap out?
@@sc29229 If the pool is full of water you will be fine, but you may get a little wet.
How restrictive is this light? Are there any specs for flow?
The aqualuminator has good flow, as far as the specs you would have to check with the manufacturer.
Hi my light is leaking from around the outside the light
The seal isn’t good anymore it’s 20 years old how can I fix it
We do carry the whole entire light and all the parts for the Aqualuminator, I am not sure what you need but if you contact me I will be able to help.
I just replaced a bulb on this unit an still no light...just a few days ago everything was working just fine...can you point me in the right direction....could it be the box where the button to turn on the the light ...or did I get a bad replacement bulb.
If your bulb is good then it might be the transformer, if you have a volt meter you can test it to see if you have power. If you have any questions feel free to contact me I will be glad to help.
@@HallmarkPoolSupplies it is not the bulb I tested the old one and it still lights up . so there it pointing towards the box where the button on and off switch is at or (transformer) how do I get ahold of you to trouble shoot this
You can contact me by phone, the number is on our website.
ok will do ..whats operation hours and whi am I speaking with
Contact me between 10 to 5 EST. Tuesday-Saturday. This is Mark.
How do you install that type of light to your above ground pool?
I have not made a video on that yet. This light is installed in the existing return. This is a light/return combination and is easy to install. The light comes with detailed instruction for installation. Feel free to contact me if you have any questions.
Do you still sell the parts for this?
Love your videos, do you recommend any other above ground pool lights