Vielen Dank für Ihren Kommentar! 😍 wenn dir dieses Video gefallen hat, teile dieses Video mit deinen Freunden ❤️ es wird die Entwicklung des Kanals unterstützen! 📈
Good job servicing the hub. I especially liked how you adjusted the bearings at the end. Thats the proper way to do the adjustment of a QR hub. A couple comments: it's better to clean the hub's cups without removing the dust covers. Yes it'll be trickier but you avoid damaging the dust covers. Also, you might consider replacing the bearing balls instead of cleaning them. They are cheap enough.
well define cheap enough. according to many bike shops it´s cheap enough to buy a whole new wheel hub included (in case of cheaper parts) instead of cleaning it. I definitely appreciate even the balls cleaned up and reused in the video but a note along that that part of the job isn´t so much worth it could do well indeed
@tomaskozler4856 Good point. Just cleaning and greasing the balls is better than no service at all. But its really hard to tell whether balls are getting worn. And since one took their time to service hub/freewheel, they might as well replace the balls.
olá. obrigado pelo vídeo. fez ótimo trabalho. bom amigo, por gentileza, se você souber. eu gostaria de saber quantos "mm" tem a passagem da agulha que você usa na seringa? "diâmetro interno".
Obrigado pelo seu comentário. A seringa não é uma agulha de farmácia, mas um bocal para cola ou fundente. Não me lembro exatamente do diâmetro interno, cerca de 1,5-2 mm.
@@NiceBikeService obrigado por responder. entendi. embora não seja agulha de uso humano ou de farmácia, o tal bocal é compatível no encaixe com a seringa usada. pode-se visto que você usa uma seringa de uso humano. em seu país ou cidade, em que tipo de comércio você encontrou o bocal pra vender ou você comprou na internet?
Guten Tag. Normales Lagerfett ist ausreichend. Wenn Sie wirklich wollen, können Sie Silikonfett verwenden, um die Dichtungen selbst ein wenig zu schmieren
Its already at the stage of breaking out the hub, have a check and maintenance for every 4 to 6 months depending on how often you ride on your bike.. always clean your bike after long ride..
You can apply a little grease to the balls of the bearing under the dust cover. Although usually these bearings are simply replaced, and the new ones already have factory grease
A visual guide to maintaining the bushing is good, but it is better to use a bushing with sealed bearings. At least that's what I do, since I got a rather ungrateful and dreary repair of bulk bearings.
OK, Bruder, wunderbares Video, Daumen richtig hoch. Hab alles so vorgefunden, wie von Dir beschrieben, nur viel dreckiger. Deswegen muss ich ja ran. Mein Problem ist aber noch eins: Mein Freilauf klemmt und ich krieg ihn nicht runter. Kennst du da einen Trick? Gibt es einen Abzieher? Gruß, Börny
@@NiceBikeService Das mag schon damit gehen. Bei mir ging der Dichtring aber von Hand ab. Nur der zu tauschende Freilauf war extrem festgebrummt. Der 12er Inbus musste leiden. Wenn er aber bis 200 Nm fest war, ist das Losbrechmoment trotzdem irgendwie gefühlt geringer. WD40 und mehrere Hammerschläge haben zum Glück geholfen.
1 thing about cup & cone system that most dont understand The ball is so much more harder than the cone & the cup. That meaning if the ball was broken then the cup&cone is useless , dont just change the ball , change the whole thing 😅
myślę że piasty na łożyskach wcale nie są lepsze od tych na konusach z dużymi kulkami - bo te stare QR9 o wiele dłużej służą a łożyska trzeba bez przerwy wymieniać ponieważ mają maluteńkie kuleczki w sobie i duży nacisk na małą powierzchnię. Jedyny plus tych łożyskowych to tylko sztywność ale jak ktoś nie jest grubasem jakimś to i na QR9 jest elegancko z dobrymi zaciskami...
Masz rację, tanie tuleje z łożyskami są gorszej jakości niż klasyczne ze stożkami. Shimano ma większość tulei z kulkami i stożkami luzem i działają one bardzo długo.
Nie mam dobrych wspomnień poserwisowych z tego typu rozwiazaniem na konusach. Serwis jest prosty, ale ustawienie odpowiedniego luzu to już jest katorga. Jeden błąd wg mnie robisz. Smar kładziemy też na bieżnię w piaście.
If you liked this video,
share this video with your friends ❤
it will help the development of the channel! 📈
Thank you for your comment! 😍
Sehr gute Kamera Führung, man schaut dem Meister über die Schulter und lernt. Sehr schön.
Vielen Dank für Ihren Kommentar! 😍
wenn dir dieses Video gefallen hat,
teile dieses Video mit deinen Freunden ❤️
es wird die Entwicklung des Kanals unterstützen! 📈
Amo seu canal. Aqui realmente é possível aprender sem deixar dúvidas ou gerar alguma insegurança nos leigos. Parabéns.
ASMR Bike Tools. Could listen to it for hours! 😄😄
glad to be of service! thanks for your feedback 😘
Iești un profesor mulțumesc
Good job servicing the hub. I especially liked how you adjusted the bearings at the end. Thats the proper way to do the adjustment of a QR hub.
A couple comments: it's better to clean the hub's cups without removing the dust covers. Yes it'll be trickier but you avoid damaging the dust covers. Also, you might consider replacing the bearing balls instead of cleaning them. They are cheap enough.
well define cheap enough. according to many bike shops it´s cheap enough to buy a whole new wheel hub included (in case of cheaper parts) instead of cleaning it.
I definitely appreciate even the balls cleaned up and reused in the video but a note along that that part of the job isn´t so much worth it could do well indeed
@tomaskozler4856 Good point. Just cleaning and greasing the balls is better than no service at all. But its really hard to tell whether balls are getting worn. And since one took their time to service hub/freewheel, they might as well replace the balls.
I enjoyed the good video. I am curious about disassembling and assembling the hub sealed bearing. Thank you.
@@NiceBikeService Thank you. More precisely, it means replacing the hub sealed bearing.
Hola, saludos desde Argentina, porqué no le ponés rulemanes en vez de bolitas, todos estan cambiado
Así es más fácil cambiar las ruedas directamente, ya que sólo se pueden poner bolas en este buje.
No, se le pone ruleman, no se usa más eso lo que haces@@NiceBikeService
Boa noite, ótimo trabalho! vc teria esses vedantes para venda? estou a procura de vedantes que sirvam em um cubo traseiro shimano claris center lock.
Olá. Não sei onde as pode comprar, fizemo-las a partir de peças sobressalentes avariadas
The tool that loose the disc cap is the same of the BB 52? Thanks!
Yes, the tool is the same for this lock ring
@@NiceBikeServicethank you very much!
olá. obrigado pelo vídeo. fez ótimo trabalho.
bom amigo, por gentileza, se você souber. eu gostaria de saber quantos "mm" tem a passagem da agulha que você usa na seringa? "diâmetro interno".
Obrigado pelo seu comentário. A seringa não é uma agulha de farmácia, mas um bocal para cola ou fundente. Não me lembro exatamente do diâmetro interno, cerca de 1,5-2 mm.
@@NiceBikeService obrigado por responder. entendi. embora não seja agulha de uso humano ou de farmácia, o tal bocal é compatível no encaixe com a seringa usada. pode-se visto que você usa uma seringa de uso humano.
em seu país ou cidade, em que tipo de comércio você encontrou o bocal pra vender ou você comprou na internet?
you not servicing the pawl too?
and this was a separate video clip, I separated the two stories. check it out on my channel)
How do you pack the hub with extra grease to make it quieter? My hub is so noisy. Thank you.
it all depends on the model of the wheel hub
Muss man zum Fetten Silikonfett nehmen (wegen der Gummidichtungen), oder reicht normales Kugellagerfett?
Guten Tag. Normales Lagerfett ist ausreichend. Wenn Sie wirklich wollen, können Sie Silikonfett verwenden, um die Dichtungen selbst ein wenig zu schmieren
Parabéns. Gostei muito desse vídeo. Bem visível a demonstração. Forte abraço. Sergio. Cidade Sapucaia do Sul - Brasil.
Obrigado pelo seu feedback. É bom saber que somos observados do outro lado do mundo😽
Superbe video , dont j'avais bien besoin , ayant quasiment le même montage merci beaucoup 👍
Je suis heureux d'être utile ! Merci pour votre commentaire 😘
Please write the name of the black part in German at the 11:00 minute.
Staubdichtung der Freilaufnabe freehub dust seal oder freehub dust seal auf Englisch
Please tell me the name of the green lubricant
Also known as Shimano premium grease.
Motorex Bike Grease 2000
Zefal’grease also
i think you can use anything grease out there
I love it. short and silence.
thank you for your comment!
Share my videos with your friends, it will help the development of the channel! 😘
Its already at the stage of breaking out the hub, have a check and maintenance for every 4 to 6 months depending on how often you ride on your bike.. always clean your bike after long ride..
Thank you for your feedback! 😘
What about bearing free hub like ARC MT009
Did you use grease or lub sir?
Thank you
You can apply a little grease to the balls of the bearing under the dust cover. Although usually these bearings are simply replaced, and the new ones already have factory grease
@@NiceBikeService and the pawl sir? What is your experience with hub pawl?
Ferramenta é a arte do profissional.
thank you for your comment!
Fazer uso do imã pra remover as esferas , muito bom .
I despise those Shimano hubs with the entirety of my soul. Every single rainy ride i had to service it 🙄🙄
You did a really neat job :)
Thank you for your comment! ❤️❤️❤️
Share this video with your friends,
it will help the development of the channel! 📈😘
Ładnie pokazane, a co za smar wyciskamy ?
Dziękujemy za komentarz. Do smarowania używamy gęstego smaru wapniowego Divinol
Boa tarde video com ótima ilustração de fácil entendimento , não para não achei top .
Co to za klucz nasadkowy do tarcz 🤔Szukam takiego głębokiego właśnie 🤔
Sam klucz jest zwykłym kluczem ze sklepu z narzędziami, a głęboka dysza została wyprodukowana przez X17
Hey, brother. What is the grease injector you are using?
Hello! An ordinary syringe from a pharmacy with a nozzle for flux or glue
A visual guide to maintaining the bushing is good, but it is better to use a bushing with sealed bearings. At least that's what I do, since I got a rather ungrateful and dreary repair of bulk bearings.
Stock bushings in most cases have balls inside, so we work with them🐱
Wie viele kostet Hinterrad reparieren?
20-50$
Thanks!
glad to be of service! thanks for your feedback 😘
Muito bom o vídeo.
Thank you for your feedback 😽
OK, Bruder, wunderbares Video, Daumen richtig hoch. Hab alles so vorgefunden, wie von Dir beschrieben, nur viel dreckiger. Deswegen muss ich ja ran. Mein Problem ist aber noch eins: Mein Freilauf klemmt und ich krieg ihn nicht runter. Kennst du da einen Trick? Gibt es einen Abzieher? Gruß, Börny
Fucking excellent! This video is about exactly what I wanted. Thank you so much for uploading this video.
I want 2 or more videos like this every day!!!!
muito bom perfeita explicação, obrigado parabens
die Metalltabletts, fast wie beim Chirurgen um die Ecke 😆😅
GL-B63R-SB/CL-X12 ?
Dziś ładna maszyna ,też mam w takim kolorze. Pozdrawiam
6:18 Das nennt man Werkzeug zweckentfremden. 😆Diese Zange ist für das Anbringen/Entfernen von Sicherungsringen Welle/Bohrungen DIN 471/472. 🤨
Aber sie leisten gute Arbeit bei verschiedenen Aufgaben😺.
@@NiceBikeService Das mag schon damit gehen. Bei mir ging der Dichtring aber von Hand ab. Nur der zu tauschende Freilauf war extrem festgebrummt. Der 12er Inbus musste leiden. Wenn er aber bis 200 Nm fest war, ist das Losbrechmoment trotzdem irgendwie gefühlt geringer. WD40 und mehrere Hammerschläge haben zum Glück geholfen.
1 thing about cup & cone system that most dont understand
The ball is so much more harder than the cone & the cup. That meaning if the ball was broken then the cup&cone is useless , dont just change the ball , change the whole thing 😅
Мені подобається це.
🔥🔥🔥
Thank you for your feedback! 😘
myślę że piasty na łożyskach wcale nie są lepsze od tych na konusach z dużymi kulkami - bo te stare QR9 o wiele dłużej służą a łożyska trzeba bez przerwy wymieniać ponieważ mają maluteńkie kuleczki w sobie i duży nacisk na małą powierzchnię. Jedyny plus tych łożyskowych to tylko sztywność ale jak ktoś nie jest grubasem jakimś to i na QR9 jest elegancko z dobrymi zaciskami...
Masz rację, tanie tuleje z łożyskami są gorszej jakości niż klasyczne ze stożkami. Shimano ma większość tulei z kulkami i stożkami luzem i działają one bardzo długo.
nao vai trocar o eixo
desta vez não 😺
j'aurais bien aimé la même mais avec un axe traversant (vtt)sur moyeux shimano 🤔
⚠ ❓ ⚠
*ASK YOUR QUESTIONS*
👇👇👇
ich habe das gleiche problem
dieses Video-Tutorial wird Ihnen helfen).
what's better than bikes and cars? The Caucasian lady sitting next to me. 🤑🤑🤑🤑🤑🤑🤑🤑😍🤪🤪🤪❤💯
😸😉👍
Spoko ale dlaczego cały film jest niemy
Jest to format wideo bez słów. Niektóre objaśnienia znajdują się w napisach
All that effort, why not do the freehub while you're there?
Nie mam dobrych wspomnień poserwisowych z tego typu rozwiazaniem na konusach. Serwis jest prosty, ale ustawienie odpowiedniego luzu to już jest katorga. Jeden błąd wg mnie robisz. Smar kładziemy też na bieżnię w piaście.
Dziękujemy za opinię😽
Dźwięk kluczy jest jak muzyka dla pięknej, tańczącej, skompo ubranej niewiasty.
Co za interesujące porównanie👍