The cones look OK. But if supply of spares is not available and the cone isn't severely worn. The bearing surface can usually be refurbished with a small lathe(a drill will work the lathe is better) and small grinder (Dremal with an elipsiod grind point) . Just remove the lock nut and spacers expose about 15 mm of axle and put it the exposed axle into the chuck with the cone surface facing out ( turn at lower speed not to low). Then use the grind point(high speed)to clean up the pits following the conture of the cone. Once that is clear and smooth wrap some emery cloth around a small screw driver or an awl ( that will give you a taper) and spin the cone at high speed and polish going to finer grit . This actually works pretty well I've been doing this for many decades and always my personal wheels have this done. That way I can keep Shimano cones in Shimano hubs they hold up a long time in a properly adjusted hub. Just a tiny tic of play in the rear hub a little more in the front. Once the quick release skewer is tightened the axle compresses and the play will be gone. My 🙏
14:17 you might want to put the thinnest layer of silicone gel on the inside contacting surface of these seals as they tend to rub and squeal in a very annoying way. Taking special care on rotor side, of course.
After how many Kilometres do you make these type of maintenance with new grease? And after how many Kilometres do you change/replace the bottom bracket?
The bottom bracket is replaced when it makes strange noises and cleaning no longer helps, or when there is play. This can happen after 500 km or 20,000 km, depending on the quality of the bracket itself, operating conditions, rider weight, etc. The same goes for the bushings: if the wheels spin well and the bushings do not play, it is better not to open them again.
@@NiceBikeService I'm curious is it better to use bicycle specific grease for cup and cone bearings? I've been using Shell Gadus grease on my bikes for years and so far no problems, although Shell Gadus is more oriented to industrial applications and it's more viscous.
Łt 43 firma obojętna Oryginalny smar Shimano ma taki jasno zielony kolor. Ale przepłacać za firmę nie widzę sensu. Można jeszcze zastosować EP 2 lecz cena zwala z nóg
When you do it every and bin practiced, you don't have to. I've done the same service so often, and I'm also doesn't have to remove the disc's! So when you don't know what you talking then please be silent. 😂🤦♂️
Takie piasty to miałem w rowerze kumunijnym dzisięciolecia temu a i tak lepsze bo z wiankiem a te tutaj to złom -teraz wymienia się całe łożysko a nie bawi ze smarem i kulkami bo to było wieki temu 😤
Dostępne są różne strzykawki, od 10 do 50 ml. Zamiast igły można kupić dysze do kleju lub topnika (sprzedawane na chińskich targowiskach lub w sklepach z elektroniką).
If you liked this video,
share this video with your friends ❤
it will help the development of the channel! 📈
Thank you for your comment! 😍
Nice workshop
Thank you😽
Po prostu zajebisty film. Świetnie, że niektóre momenty przyspieszone. Dla mnie Oscar :-) yyy dla Ciebe
Dziękujemy za opinię😸
The cones look OK. But if supply of spares is not available and the cone isn't severely worn. The bearing surface can usually be refurbished with a small lathe(a drill will work the lathe is better) and small grinder (Dremal with an elipsiod grind point) . Just remove the lock nut and spacers expose about 15 mm of axle and put it the exposed axle into the chuck with the cone surface facing out ( turn at lower speed not to low). Then use the grind point(high speed)to clean up the pits following the conture of the cone. Once that is clear and smooth wrap some emery cloth around a small screw driver or an awl ( that will give you a taper) and spin the cone at high speed and polish going to finer grit . This actually works pretty well I've been doing this for many decades and always my personal wheels have this done. That way I can keep Shimano cones in Shimano hubs they hold up a long time in a properly adjusted hub. Just a tiny tic of play in the rear hub a little more in the front. Once the quick release skewer is tightened the axle compresses and the play will be gone. My 🙏
14:17 you might want to put the thinnest layer of silicone gel on the inside contacting surface of these seals as they tend to rub and squeal in a very annoying way.
Taking special care on rotor side, of course.
топова дощечка з вирізом під гайку)
їй 8 год 😂
@@NiceBikeServiceДе ви знаходитесь яке місто?
це секретна лабораторія 😂😂
Well done. 👋
💁😘
Nicely done, i relubed my TREK 6000 MTB wheel bearings only last week 👍 Au BTW, Please take care 🙏
Thank you for your feedback 😽
Awesome content! What kind and brand is the light green grease that you use?
For lube, we use thick calcium grease Divinol
After how many Kilometres do you make these type of maintenance with new grease?
And after how many Kilometres do you change/replace the bottom bracket?
The bottom bracket is replaced when it makes strange noises and cleaning no longer helps, or when there is play. This can happen after 500 km or 20,000 km, depending on the quality of the bracket itself, operating conditions, rider weight, etc.
The same goes for the bushings: if the wheels spin well and the bushings do not play, it is better not to open them again.
Can you fit bearings in this same hub ...bcoz i am using the same hub
We can, but our workshop is located in another country😺
Hey! I really like your content! Do you have other social medias? I couldnt find them on your yt profile.
Thank you for your feedback. For now, only RUclips 🐱
안녕 하세요 질문 하나 드릴게요 ... 저도 6각볼트 디스크 패드 사용하는데 볼트 6개중 한개가 철물점 자동차 정비소 ... 자전거 수리점 까지 갔지만 빠지질 않네요 ㅡㅡ ,,,,, 추천 하는 방법좀 알고 싶어서요 ^^
어떻게 적합한 볼트를 찾지 못하셨나요?
@@NiceBikeService 볼트 남은거 하나가 풀리지를 않으니 난감하네요... 나사산도 뭉그러진거 같은데 ,,,,,
예, 그럴 수 있습니다. 하지만 경험이 많은 자전거 정비사라면 쉽게 수리할 수 있습니다.
@@NiceBikeService 방법을 물어보고 싶어요 ㅠㅠ
채널을 계속 지켜봐 주세요. 곧 이 주제에 대한 동영상이 게시될 예정입니다.)
Скажіть будь ласка, яку змазку ви використовуєте для підшипників?
divinol
@@NiceBikeService дякую
У нас в майстерні кальцієвий Divinol
Is that Shimano premium grease?
yeas
@@NiceBikeService I'm curious is it better to use bicycle specific grease for cup and cone bearings? I've been using Shell Gadus grease on my bikes for years and so far no problems, although Shell Gadus is more oriented to industrial applications and it's more viscous.
A more viscous one will ruin the roll of the bike's wheels. And a more viscous one will leak out from under the hub dusters.
❓❔❓
*Ask your questions in the comments*
👇👇👇
dziekuje za ciekawy film. Jaki to jest smar do łożysk?
Też bym chciał wiedzieć
@@marcinkowalski8353 Wygląda na Motorex FETT 2000
Łt 43 firma obojętna
Oryginalny smar Shimano ma taki jasno zielony kolor. Ale przepłacać za firmę nie widzę sensu.
Można jeszcze zastosować EP 2 lecz cena zwala z nóg
Dziękujemy za opinie i komentarze😺. Używamy gęstego smaru wapniowego "Divinol"
my cones are damaged can they be replaced ?
Only the Cones at the Axle. The cones inside of the hub can't replaced.
Yes, you also need to replace the balls
Working with grease and dont remove the disc first!
Well done! 😂
When you do it every and bin practiced, you don't have to. I've done the same service so often, and I'm also doesn't have to remove the disc's! So when you don't know what you talking then please be silent. 😂🤦♂️
A little training and you will succeed😸
Bhai where do you live? 🚴🚴😳
Hello. We live in Ukraine 🐱 🇺🇦
@@NiceBikeServicehy bro nice your video i learn ❤
if you liked this video,
share this video with your friends ❤️
it will help the development of the channel! 📈
Takie piasty to miałem w rowerze kumunijnym dzisięciolecia temu a i tak lepsze bo z wiankiem a te tutaj to złom -teraz wymienia się całe łożysko a nie bawi ze smarem i kulkami bo to było wieki temu 😤
Dopóki koła się kręcą, można się nimi bawić 😺.
Jaka igłę masz to strzykawki jaki jej rozmiar stosujesz?
Dostępne są różne strzykawki, od 10 do 50 ml. Zamiast igły można kupić dysze do kleju lub topnika (sprzedawane na chińskich targowiskach lub w sklepach z elektroniką).
@@NiceBikeService zastosowałem jeszcze coś innego tańszym kosztem jeszcze
✅
@@NiceBikeService ja sobie zastosowałem wężyk gumowy i też daje radę
Najważniejszy jest wynik, a mogą być różne sposoby👍
Ця втулка не потребувала обслуговування 😊
Її власник вирішив інакше😸
Do you use any regular type of degreaser to clean parts?⚙️🔩🚲
I use isopropanol and camp fuel