Thank you for putting up the eye protection reminder at the end. Also, even when you're spraying the soapy water, it doesn't hurt to wear a filter mask to protect your lungs from any particles that might still escape into the air.
I absolutely love the positive dust suppression, removing the hazard (because carbon fibre dust is really nasty), instead of relying on a mask, and sending up a dust cloud around the workshop.
nice video Calvin...the soapy water and tape tips are great given the amount of times I have cut seat posts and steerer tubes! thanks for all the help over the years!
You make it look so easy, I need to do mine but I don’t have one of those fancy guides and I’m not 100% sure my old bike is set up good enough to measure off 😬
Damn, Calvin wasn't kidding when he said he was going to use a hacksaw on a carbon fiber bike! I was waiting for him to stop and show one of the cool tools he always has :-D
A lot of people are criticizing Giant's design here, but keep in mind that this is a carbon bike with Di2. Probably a racer. The weight savings is probably pretty significant. Also, Calvin, wear PPE whenever using a cutting tool!
Thank you very much for the video. Very instructive. But I have a question: What can we do if the cutting be more than necessary or if you find a second hand frame with that problem?
My seat is a little too high for 20 yrs it was fine. Not sure if it is an aging thing. I tried to lower my seat when removing the mast and saddle I was shocked to see a cut going around the carbon seat post. I have the shortest mast presently, so hopefully a 1/2 cut will do it. Of course bike shops say buy a new bike.
I love the way Calvin is always thinking about the ergonomic aspect of working on bikes. Home mechanics may have a harder time without the high tech bike station.
I don't know, my stand will rotate, and the height is adjustable. Raising and lowering the bike takes a bit more elbow grease than just pushing a button, but it can be done.
I’ll get the Propel Advanced SL in a week. Hope the Giant store works at the same level as you do! How many mm spacers can you use maximum? Just in case I need to higher the seat when I change crank length....
I have a 2014 TCR Advanced SL 0 with the same kind of seat post clamp in this viseo. I am using two spacers on top of the actual fiber carbon seatpost (part of the frame) then the clamp with the saddle. The problem I am having is a crazy creaking coming from the seatpost/clamp. I tried already using grease, carbon grease, even putting electrical tape around the carbon seatpost. Any suggestions on how to get rid of the creaking noise? Thanks in advance.
Are you sure it is not the saddle/ rails and where they attach? These seatmast caps are not necessarily known to creak but the clamp for the rails is. Remove that, clean, grease threads and re install.
Ooops! I thought,,,,,,, Nope! I'm in no hurry for this. I'm pretty sure the weight loss isn't worth it, to me. Video is excellent, but this is just too much of a pain for the return. Oh yeah, and let's acquire some more tools that I can toss with the next change.
Manufacturers that use seat masts put thought into the bike being clamped and build it to be able to be clamped. Sawing is intended my the manufacturers and the only ill effect would be if you cut too much off. Which leads you to plan b which is typically a conversion post.
@@parktool i have a 2022 tcr sl and i am goin crazy with a creaking sound ? Is it a must to use a shim? The bike Shop has put a vinyl between the seat mask and the frame to make the system work properly but there is not shim installed and i am wondering if i have also to put a shim .to avoid a y creaking sound . Thanks for your help
Perhaps you should discuss these "insignificant quantities" of carbon dust with someone who actually knows what carbon can (and will) do from a corrosive standpoint to some metals. This dust will fall down into the bottom bracket area, which could cause issues at some point, where your crank spindle and bearings live. Why on earth wouldn't you take the time to remove it to avert that possibility?
It does not take much carbon dust to cause serious health problems if you breath it in. If you cut carbon once every few years, you'd probably be fine. If you work on carbon bikes for a living, and don't take precautions, you will probably die an early death of major respiratory problems. "Insignificant" does not belong in any sentence describing a potentially fatal health hazard.
@@greenpedal370 Professional do this a LOT, mostly on steerer tubes and handlebars. If you want to expose your lungs to a carcinogen, that is your right, but encouraging other to do the same, or criticizing those who are encouraging good safety practice, is negligent and foolish.
It's a design feature intended for a more bespoke use. One rider wanting to shed every single ounce to go as fast as possible. Not really practical for typical consumer use, but very very practical for those riding competitively.
There is some adjustability in the height of the mast cap. If you really need to make it higher than possible some companies give you the option to put a standard post in. But this is not common and cutting too short is a very bad thing.
At about 9:43 you can clearly see a substantial pile of carbon fiber filings inside the tube, above the Di2 unit, which should have been cleaned out before righting the bicycle and attaching the seat. Details matter, sir. Steve
@@zygmuntthecacaokakistocrat6589 Yes. Anybody wondering why can take a look at the cross section of the mast during the cutting. Very thick front and back, not so much on the sides.
No, it does not absorb water, or even grease/oil. Chemically, carbon fiber is very inert. This is one reason some sailboats and windmills are made from carbon fiber.
@@CyclingSteve The soapy water doesn't get it all. It helps, but a mask is still a good idea. You know, if you do this on a regular basis (professionals) and want to keep breathing well into old age. If those things don't apply to you, then a mask is not really necessary.
Any kind is fine. Just plain water works better than nothing as well. A vacuum would usually do the trick but most people don't have the extra hands or a fixture to go that route.
@@adriangandara4715 - You may have an IQ of 250, but you do lack some basic understanding of things. He was using the soapy water to prevent flying dust, which was in small volume as it's not a power tool process. The use of soap is weird and useless water is a lame solution to begin with, unless you are cutting masonry or some other very dirty materials with power tools blowing it everywhere, or wish to collect every bit of dust waste for reuse later. I don't like putting water near batteries (the object inside the seat tube is a battery), and the muck he creates just sits there and needs to be cleaned out anyway. So I suggest a vacuum held near the sawing action, quick neat easy done. This is standard procedure in the trades where you make dust. I love this guy, but as you can see when he refers to the "Doppler effect" he does have his limits of knowledge/understanding as do we all.
@@johnsmith1474 I ask questions about things when I want to understand them better. I've only cut a carbon steer tube and didn't use anything but a hacksaw and a vise. I asked because I know some soaps have chemicals in them. I wasn't sure if that could damage the paint or clear coat. I don't like people who make jokes or talk down to people who ask questions. Reminds me of kids who bully other kids in school, or make fun of them when they ask questions that they deem to be stupid. I know it's the internet so people feel entitled to say what they want because they're no repercussions. My name is on my account and my face is my avatar because I conduct myself online as I would in real life, like a man. It seems to me you should make your own videos since you know better than most. Then you could save your breath and wouldn't have to make quips or judge others who are actually helping people who know less than them. You also have no idea what I lack or have in abundance. If you're ever close to El Paso, TX I would love to show you.
John Smith : I’m retired 50 years of the working world still have all limbs and in good health. Just trying to keep other from dying! By the way if do use a vacuum make sure it’s hepa filter if not your going breath in carbon fiber dust
@@rjg3876 - You could rent time with one of those boxes with remote arms they have for handling plutonium. You could just cut it outside. Or if you only do it rarely, you could ignore the issue because it's not an issue and no you don't need a HEPA filter for a little say action. You are doing nothing to "keep others from dying" you are bullshitting yourself.
John Smith : have fun with your potentially bad Heathy life. I made thru 35 year in the Elevator industry. could of been killed at any time had think all time. something I don’t think you can do
You could use a Japanese saw, or razor saw. You need to have a vacuum in play, not soapy water (9:44 it looks like a pile of crap in there). It's silly to be shooting water into the frame. It's not the "Doppler effect" ha ha you are not moving at speed past the object emitting (sound) waves thus invoking a change in relative wavelength, it's just the change in resonance of the seat mast, as it is divided. When you dress it up, use a block. For someone actually doing this, consider they might not own an electric bike lift. You might have lectured on the option of making the cut with respect to adjustability (your idea of lending the bike) that is, cut it some measure shorter so that the user can both lift, or lower the seat a tad. As you cut it, it can now only be lifted, not lowered.
I may never have to use this video for a tutorial, but the videos are so dang entertaining and I can’t stop watching them
Me to i am a mtb rider i don't know why i watched this
Thank you for putting up the eye protection reminder at the end. Also, even when you're spraying the soapy water, it doesn't hurt to wear a filter mask to protect your lungs from any particles that might still escape into the air.
Nice work stand.
The bike industry has the tendency of inventing stuff to make our lives more difficult. I dig my threaded BB and 27.2 seat post.
Gabriel Miquéias they’re not really superior, just do a better job of masking the manufacturing errors that most big brands make
I absolutely love the positive dust suppression, removing the hazard (because carbon fibre dust is really nasty), instead of relying on a mask, and sending up a dust cloud around the workshop.
nice video Calvin...the soapy water and tape tips are great given the amount of times I have cut seat posts and steerer tubes! thanks for all the help over the years!
@Tom Anderson totally agree! I use mask and eye protection on all my builds.
Fantastic work! Very detailed and shows how needs to be done properly step by step!
Calvin is the BEST----thank you so much!!!!!!!!!!!!! ❤ 🧡 💛 💚 💙 💜
You make it look so easy, I need to do mine but I don’t have one of those fancy guides and I’m not 100% sure my old bike is set up good enough to measure off 😬
Damn, Calvin wasn't kidding when he said he was going to use a hacksaw on a carbon fiber bike! I was waiting for him to stop and show one of the cool tools he always has :-D
The blade is the cool tool. It's specially made for carbon fiber cutting.
A lot of people are criticizing Giant's design here, but keep in mind that this is a carbon bike with Di2. Probably a racer. The weight savings is probably pretty significant. Also, Calvin, wear PPE whenever using a cutting tool!
I was cringing through the whole thing - no glasses, no mask. Soapy water only goes so far...
Wow, just wow. One take! (Up to the cut)Anyone else want to risk their multiple thousand dollar bike in one take?
@parktool well done!
Thanks, I really need it, this guidance help me and now I know how to do it
Nicely done sir!
Great job park tools
Great stuff. Park Tool rocks
Thank you very much for the video. Very instructive. But I have a question: What can we do if the cutting be more than necessary or if you find a second hand frame with that problem?
This guy is amazing!
If Norm Abram, (New Yankee Workshop), had worked on Bikes
instead of solid wood, he would have done it this way. Well done.
When Calvin taped it, I was absolutely thinking about woodworking. Great way to reduce blown out fibers for a clean cut.
Like the stand
Such a total overdesign of a seatpost
Moi j'adore , merci à la prochaine . Thank you . ) 👍
My seat is a little too high for 20 yrs it was fine. Not sure if it is an aging thing.
I tried to lower my seat when removing the mast and saddle I was shocked to see a cut going around the carbon seat post. I have the shortest mast presently, so hopefully a 1/2 cut will do it.
Of course bike shops say buy a new bike.
I have the same.. But normal because the joints between ankles, knees and hip become thinner about half a cm.. Times 3
I love the way Calvin is always thinking about the ergonomic aspect of working on bikes. Home mechanics may have a harder time without the high tech bike station.
I don't know, my stand will rotate, and the height is adjustable. Raising and lowering the bike takes a bit more elbow grease than just pushing a button, but it can be done.
I’ll get the Propel Advanced SL in a week. Hope the Giant store works at the same level as you do! How many mm spacers can you use maximum? Just in case I need to higher the seat when I change crank length....
Where to do you get the spacers ? Bought one n need the post higher
Is it somehow necessary to seal the carbon after the cut?
It is not necessary but some do opt to seal the end of cut with clear fingernail polish.
Can i use a powered circular saw for this?
I have a 2014 TCR Advanced SL 0 with the same kind of seat post clamp in this viseo. I am using two spacers on top of the actual fiber carbon seatpost (part of the frame) then the clamp with the saddle. The problem I am having is a crazy creaking coming from the seatpost/clamp. I tried already using grease, carbon grease, even putting electrical tape around the carbon seatpost.
Any suggestions on how to get rid of the creaking noise? Thanks in advance.
Are you sure it is not the saddle/ rails and where they attach? These seatmast caps are not necessarily known to creak but the clamp for the rails is. Remove that, clean, grease threads and re install.
Park tools are affordable and good quality. Thanks.
Not sure about the affordability part but definitely top quality
Ooops! I thought,,,,,,, Nope! I'm in no hurry for this. I'm pretty sure the weight loss isn't worth it, to me. Video is excellent, but this is just too much of a pain for the return. Oh yeah, and let's acquire some more tools that I can toss with the next change.
What’s the product name of the integrated seat mast clamp?
should have shown us how you measure the rider height against the ISP prior to cutting.
Do you have to be careful when clamping the seat mast, would the sawing have any adverse effects on the clamped section?
Manufacturers that use seat masts put thought into the bike being clamped and build it to be able to be clamped. Sawing is intended my the manufacturers and the only ill effect would be if you cut too much off. Which leads you to plan b which is typically a conversion post.
any particular blade you like to use? Doing this later.
For carbon, 32tpi.
@@parktool Thank you so much. That blade looked completely different than a 32tpi blade was that carbon specific? Sorry to ask.
What's the battery thing that was pushed down? What is it used for?
That is to power the Di2 shifting system on the bike.
Is it okay or safe to put the seat mast on the maximum limit insertion cap? My bike is emonda, thanks
As long as you do not go past the line you are good to go.
I was wondering if I could run the seat mask without shims? Will it damage the seat mask?
Always check with the manufacturer
@@parktool i have a 2022 tcr sl and i am goin crazy with a creaking sound ? Is it a must to use a shim? The bike Shop has put a vinyl between the seat mask and the frame to make the system work properly but there is not shim installed and i am wondering if i have also to put a shim .to avoid a y creaking sound . Thanks for your help
The funniest thing about these comments are the hysterical remarks regarding insignificant quantities of carbon dust.
Perhaps you should discuss these "insignificant quantities" of carbon dust with someone who actually knows what carbon can (and will) do from a corrosive standpoint to some metals. This dust will fall down into the bottom bracket area, which could cause issues at some point, where your crank spindle and bearings live. Why on earth wouldn't you take the time to remove it to avert that possibility?
It does not take much carbon dust to cause serious health problems if you breath it in. If you cut carbon once every few years, you'd probably be fine. If you work on carbon bikes for a living, and don't take precautions, you will probably die an early death of major respiratory problems. "Insignificant" does not belong in any sentence describing a potentially fatal health hazard.
Good grief we are talking someone cutting a seat post, not industrial applications. Like I said Hysterical.
@@greenpedal370 Professional do this a LOT, mostly on steerer tubes and handlebars. If you want to expose your lungs to a carcinogen, that is your right, but encouraging other to do the same, or criticizing those who are encouraging good safety practice, is negligent and foolish.
@@backpacker3421 Oh please.
Ohhhh, Metric, always love Calvin using Metric, American must be losing it watching this!
Great video... sure seems like a bad design that unnecessarily limits the bike's sizing.
It's an engineers delight.
It's a design feature intended for a more bespoke use. One rider wanting to shed every single ounce to go as fast as possible. Not really practical for typical consumer use, but very very practical for those riding competitively.
1:38 Loan it to a friend?
🤣 Calvin you must be joking! Are you on drugs?
So what to do if you HAVE to make higher .. can I stack or do I have to replace the post
There is some adjustability in the height of the mast cap. If you really need to make it higher than possible some companies give you the option to put a standard post in. But this is not common and cutting too short is a very bad thing.
@@parktool how higher i can adjust the mast cap? What if i cut to low 2-3cm?
Oh my god, I almost cried when he lowered the bike stand electronicaly. I was expecting a crushing sound :|
At about 9:43 you can clearly see a substantial pile of carbon fiber filings inside the tube, above the Di2 unit, which should have been cleaned out before righting the bicycle and attaching the seat. Details matter, sir.
Steve
Thanks for your concern Steve.
Great thought by giant marketing. Hmmmm one bike fits possibly one person = more sales = kills the secondhand market 🤔
Yhea, you really don't want to use the caliper to scribe on stuff. Calibers precision comes from how sharp their blades at the tips are.
Mainly when putting things together
But what happens if you buy this bike you have to get the seat post for your hight but you grow higher then what happens?
Thought you weren't supposed to clamp down on carbon like you're doing with the workstand clamp on the seatmast.
If you're careful, you can clamp on almost anything. See this video for more of our thoughts on the matter: ruclips.net/video/ix_e6LWvap0/видео.html
@@zygmuntthecacaokakistocrat6589 Yes. Anybody wondering why can take a look at the cross section of the mast during the cutting. Very thick front and back, not so much on the sides.
Cutting a steerer tube to slam the stem in one thing. But having to cut the frame adjust saddle height. No thanks Giant.
doesn't carbon arbsorved water?
No, it does not absorb water, or even grease/oil. Chemically, carbon fiber is very inert. This is one reason some sailboats and windmills are made from carbon fiber.
What if you need an extra 1mm
no mask?
Please. Find a safe place.
Soapy water...
@@CyclingSteve The soapy water doesn't get it all. It helps, but a mask is still a good idea. You know, if you do this on a regular basis (professionals) and want to keep breathing well into old age. If those things don't apply to you, then a mask is not really necessary.
@@johnsmith1474 I'm sorry, did Rich's concern for proper safety trigger you?
Good video, but I would have liked for you to mention the reason it's important to keep the carbon fiber dust out of the air: It's carcinogenic.
Which is why using soapy water AND a mask is a very good idea. Soapy water prevents most dust from reaching the air, but not all.
Can you cut a carbon fiber post?
Yes, certainly. Measure a couple of times first. Finish the end with sandpaper.
What kinda soap? Dish? Does it matter? Thanks.
Are your joking? Just use a vacuum.
@@johnsmith1474 no I wasn't joking. I guess I'm not as smart as you.
Any kind is fine. Just plain water works better than nothing as well. A vacuum would usually do the trick but most people don't have the extra hands or a fixture to go that route.
@@adriangandara4715 - You may have an IQ of 250, but you do lack some basic understanding of things. He was using the soapy water to prevent flying dust, which was in small volume as it's not a power tool process. The use of soap is weird and useless water is a lame solution to begin with, unless you are cutting masonry or some other very dirty materials with power tools blowing it everywhere, or wish to collect every bit of dust waste for reuse later. I don't like putting water near batteries (the object inside the seat tube is a battery), and the muck he creates just sits there and needs to be cleaned out anyway. So I suggest a vacuum held near the sawing action, quick neat easy done. This is standard procedure in the trades where you make dust.
I love this guy, but as you can see when he refers to the "Doppler effect" he does have his limits of knowledge/understanding as do we all.
@@johnsmith1474 I ask questions about things when I want to understand them better. I've only cut a carbon steer tube and didn't use anything but a hacksaw and a vise. I asked because I know some soaps have chemicals in them. I wasn't sure if that could damage the paint or clear coat. I don't like people who make jokes or talk down to people who ask questions. Reminds me of kids who bully other kids in school, or make fun of them when they ask questions that they deem to be stupid. I know it's the internet so people feel entitled to say what they want because they're no repercussions. My name is on my account and my face is my avatar because I conduct myself online as I would in real life, like a man. It seems to me you should make your own videos since you know better than most. Then you could save your breath and wouldn't have to make quips or judge others who are actually helping people who know less than them. You also have no idea what I lack or have in abundance. If you're ever close to El Paso, TX I would love to show you.
Xe đẹp .
How to know if you cut it too short? is there like a danger area for these types of seatpost? I have an emonda SL5 and I need to cut it :(
What happens when your mate gives you the bike back and you want to return it to its original height 🤷🏻♂️😉
Dont lend you seat mast equipped bike to your buddy ;)
Park Tool exactly right
26 for MTB life. Old school 27 1/2 inch rims for road.
I just losen the bolt and remove it and ride my bike til it loose
Shouldn’t you have an respiratory device on when cutting carbon fiber?Remember your teaching people
he showed in the video he wet it with like water to keep the carbon dust from flying every where
I suggest the use of a vacuum not water. But I must your generation is lost in fear. What the hell are you going to do to survive in a working world?
John Smith : I’m retired 50 years of the working world still have all limbs and in good health. Just trying to keep other from dying! By the way if do use a vacuum make sure it’s hepa filter if not your going breath in carbon fiber dust
@@rjg3876 - You could rent time with one of those boxes with remote arms they have for handling plutonium. You could just cut it outside. Or if you only do it rarely, you could ignore the issue because it's not an issue and no you don't need a HEPA filter for a little say action. You are doing nothing to "keep others from dying" you are bullshitting yourself.
John Smith : have fun with your potentially bad Heathy life. I made thru 35 year in the Elevator industry. could of been killed at any time had think all time. something I don’t think you can do
Can you guys sell your company products to Nepal please here is not available tools to make my cycle run please reply
Shops and customers looking for our products in Nepal should contact our distributor in India. HAPPY EARTH ENTERPRISES LLP
Do I need to seal the cut carbon fiber with something?
You could use clear nail polish if it made you feel better. I've never been told to need anything more than cleaning up the edges
@@mrfailure93 Thanks!
@@mrfailure93 - Every guy has that around.
@@johnsmith1474 Just like every video has a troll!
@@mrfailure93 - Nice to see you self identify.
Adds about £300 for the bike manufacturer every time you need a replacement. Don't you just love modern engineers 🤬
worst design ever
You could use a Japanese saw, or razor saw. You need to have a vacuum in play, not soapy water (9:44 it looks like a pile of crap in there). It's silly to be shooting water into the frame. It's not the "Doppler effect" ha ha you are not moving at speed past the object emitting (sound) waves thus invoking a change in relative wavelength, it's just the change in resonance of the seat mast, as it is divided. When you dress it up, use a block. For someone actually doing this, consider they might not own an electric bike lift. You might have lectured on the option of making the cut with respect to adjustability (your idea of lending the bike) that is, cut it some measure shorter so that the user can both lift, or lower the seat a tad. As you cut it, it can now only be lifted, not lowered.
Fuck thats funny
I laugh at the way he talks every last word comes up in tone and volume . have a listen drama guy for sure