Fully Rebuilding a 5.4l 3v Triton for big boost! Twin Turbo F150 Ep.8
HTML-код
- Опубликовано: 1 мар 2022
- Thanks agian to maxpeeding rods! MaXpeedingRod turbos: bit.ly/3sz0UIj
Coupon code: Mechan(5% discounts for all orders)
as you know, this project has been in the making for quite a while now and I'm so excited to get this finished! the twin turbo f150 is going to be so insane when it's finished!
if you like the twin turbo f150 then u'll really enjoy the next video!
check out our Tiktok!
vm.tiktok.com/TTPdA87Xnd/
check out our Instagram!
mechanaholics
Link to the turbocharger in the video!
www.maxpeedingrods.com/produc...
Thank you Everyone watching.
And Keep on Boosting the Word! 
Авто/Мото
This video really just like, set the bar for me to make another bad financial decision for my truck 😂😂
He Fast forward through the learning parts!! Unless you’re just watching to be watching, this is your video!
I never knew that there much aftermarket support for upgrading the 54 3 valve
Thanks for the informative video, keep up the good work!
Cool I've never seen anyone rebuild a 3 valve 54. Are educated young man and the good work hope everything works out for you
Just watched all your 5.4 TT videos! Awesome stuff, can’t wait for the next one!
It's going to be amazing!! I cant wait to show the world! Thanks for watching! It means alot!
I’m on my 3rd build now , I’m doing the 5.4l 3v as well and super charging it
Haha never gunna find that piston pin clip now!
Love this video.
Great Vid Man!!!!❤🤟😎👍
You use the stock block?
What rods and pistons did you use?
Positive criticism on video taking only. Do your best to move the camera much slower so we don't get vertigo or motion disturbance! I loved the information you provided us! God bless my friend! 😊😊😊😊
Drink beer. It will help
🔥
Whats main and rod bearing clearence ?
👍
How much did this cost in total?
You guys back in Tejas? Do you guys work on VW/Audis?
Dude your awsone!
Where have you been
so as long as my cams and crank are set at tdc i can install the heads with the cams already installed in the heads and bolt it up without worrying about any interference from the valves to pistons?
They are a non interference engine from what I can tell so it shouldn’t matter
@@opp_slider3223 it is not a non interference engine i'm sitting here with one right beside meabout to put the heads on
@@thomasv5596 well then I must be retarded because when I did my timing chains you can spin the cam 360 degrees and none of the valves hit the pistons 😐
@@opp_slider3223 i'm not sure what your engine type is, but valves and pistons will clearly make contact if you look at the heads the valves clearly extend past the surface of the head and the pistons come almost to the top of the block, about an 1/8th of an inch from the top. as well as a simple google search and multiple forums that state clearly that the 5.4 3v is not a non interference engine, hence the notorious lash adjuster installation process.
it's an interference engine. timing chain breaks or you get it too far off, carnage
Question I have a 2004 f350 crew cab 4x4 5.4l 4700 auto trans. Has the famous ticking when starting up goes immediately away. So doing a complete timing set new camshafts and roller rockers new phasers. This is a service/utilitie body. I have a complete another truck with the 7.3l powerstroke. Basically want to take engine/trans/t case complete wiring harness ecu. I know its alot of work but got the 5.4l a nd Trans out not much for me to take the dash out and wiring harness! Would the ring and pinion need to be swapped? And front and rear shafts would they work for the diesel? 2000 year model 7.3 powerstroke auto 4x4 crew cab rolled over a d frame damaged. Have shop and lift. Got cab off diesel already. And advice? My first diesel swap. This truck spends long hours on the hwy hualing heavy tools and parts all day.
It depends on the differential you have. My f150 has a Dana 60 rear end so it can handle alot but as long as you keep both front and rear differentials it shouldn't matter as far as gear the gear difference. I would measure the distance between the 2 drive shaft plates on the front and pull both driveshafts from the rear and compare the two, and as long as you can mount the engine in the same place as the other engine it should space fine. I'm working on a new setup for the f150 and I'll be doing solid engine mounts so I'll be able to post some of that footage here soon.
What is the hp limit for a stock 5.4 3v i am contemplating doing a 5.4 3v swap in my 2010 mustang gt didn’t want to do the usual coyote swap and figured it would still look swap esp if it fits under the hood
I've heard right around 500hp probably be safe for a while at 450hp on stock internals , but don't quote me just what ive heard
Same here, 08 GT Convertible..
So I have a Lincoln with I believe the same engine (it’s a 2012 navigotor l) how much would it cost to make 600-700 whp and do a stand alone
Stand alone ecu (no real budget just trying to price things out for the build.
Do you do F-150 Ford 4.6
2006
I have a 2005 f150 that's been sitting about 10 yrs now little single cab with the 4.6 what would it cost to rebuild motor for boost and put a turbo in with a good transmission
I spent alil over 50k overall on my build and im still not finished with it. But I'd say anywhere between 20 and 40k if done right. That's why everyone Ls swaps everything because there cheap and can handle everything. But getting a good transmission is expensive and the labor and parts alone to build the engine for boost is really expensive and same with getting custom exhaust for turbocharging. There's not really any parts support with these engines, so everything has to be custom made and that makes it really expensive.
I should have the next video finished soon hopefully, it's been taking a while because my welder broke and can't finish the custom exhaust yet. I'll make an update video here soon.
It can be done cheaper but I wouldn't recommend it cus that's what I tried to do and ended up rebuilding and redesigning it 3 times to get it to where it is now. These engines are complicated lol
@@MechanaholicsCreations where’d u get your parts from?
Didn't gap your rings with that turbo install I bet.
There's a whole section in the video about gapping the rings lol
Gonna have to get the address to your shop, I'll drop my 5.4 3v for you to build a masterpiece ✨️
Definitely! I've done quite alot of 3v builds and can definitely bulletproof it for you! Email is Corbinscustoms.info@gmail.com
What about ring orientation?
Nonbinary, pretty sure.