@jasonmangila The high beam on the headlights are generally fixed. However, you still have the option to adjust them to the height desired. Thanks and good luck.
These also come with brackets that you needed to fit onto your vehicle. did you miss that? if anything, please review this video again to see if you have missed anything.
@jasonmangila Almost all the projectors have a screw in the back that can help you adjust the low beam. There will be either two or four. For up down left right. Please check with your selling to make sure. Thanks and good luck
apologies on that, you are correct sir. but unfortunately we do not have an aftermarket tail lights on our website so therefore we couldn't give you a correct answer. but yes, the only difference from 02-04 and 06-07 are the face-lifts and pre-face lifts. tail lights are about the same unless you are driving the wagon
Once you take out your old headlights you wont have the ballast anymore so technically you wont have the factory HID's anymore. So yes youll be fine with these headlights.
@SuperRoscoe666 Sir, we do remind everyone that there is a separate installation instructions on how to wire your halos and leds, it is stated in middle of the video. our installation instructions do not provide that also.
this set is exactly what I want on my wrx, but after watching this video I see how much work is required. Based on my resources I know this would be a big pain and would just have to take it somewhere to be done for me.
This dudes video showed wayyy too many steps at the beginning, only thing you have to do to install the lights is to take off the grill and you can remove both headlights and replace them
I agree.. I'm not ire when the previous owner pit these one but the lenses are yellowed and textterd. H1s are a pain to change.. why not just use the factory style bulbs
I'm sure these will perform much better than stock, but aesthetically IMHO these are rice. the 3 LED's above the low and high beam? For what? And not 1 pair but 2 pairs of angel eyes? I've looked for a nice set of prjectors since 05' and I haven't found one yet
@Specdtuninginfo ok thanks also something i should of ask was about the high beams as well was, are these fixed like the stock assembly? not sure how high beams are aimed where your from?
NO, theres a reason why they give you a specific year because of fitment. The only way to actually make it fit is if you can convert your 02-04 to an 06 and rewire.
Ok I'm planning in getting these lights for my 05 Sti. My question is my car comes with HIDS. What bulb comes with the low beam are they gonna be able to handle the power from my stock HIDS ?
Great thanks for your feedback! Is there another hole for parking lights, because compared to factory lights again the parking orange light is located in that exact place where the indicator hole is.
This may be a silly question but are these headlights more designed for LHD, RHD or can work effectively in both WRXs. I am considering these, but thought i'd ask first.
It depends on the Web sites you get them from, the one I got them from, since it was local to me sold them in RHD, so just check the description to be safe
How does one go about replacing the 3 little led bulbs per headlight? What's the part number or bulb type and size? Tha j you. 2 of mine finally burned out
I have just bought these lights,the leds dont replace the indicators if you pause it at 8.26 you can see the indicator holes in the far corner, I have silva tec bulbs which appear silver but flash orange
Hello! I have a question about the turn signals. On the OEM headlights, the turn signal is that orange section in the top middle. With these halo lights, the 3 LED's take the place of that section. My question is, are the 3 LED's the turning signal on these halo headlights? Also, will the turn signal with the new headlights be orange? In all the photos and videos I have seen, the 3 LED are illuminated white. Please let me know. Thank you in advance!
I bought these lights for my 2005 Sti, which was said was compatible with. I attempted to install and none of the plastic clips from the new headlights would fit with the ones on my car. Am I overlooking something?
Can these housing handle 6000k Hid bulbs, I bought these and they came with hids and ballasts, and I'm curious if they will go good together and be able to handle it?
amazing how hard it is to find projector headlights for the 04-05 wrx WITHOUT those darn tri-LED things. AB-SOLUTELY ANNOYING. considering getting eyebrows with these. otherwise i have seen these as a great product! btw does anyone know what size HID bulb these take?
R Rod No HID's were installed. The headlights are equipped with H1 halogen bulbs. The high and the low beam are a simple plug and play. You will need to wire the halo and LED bulbs to your daytime running lights.
Hi, The black and white cables are for the HALO and/or LED lights in the headlights. You would have to splice and then tap them into the corner light harness or low beam harness to the corresponding wires. The black/negative wire should be tapped to a corresponding negative wire in the harness and the white/positive wire should be tapped into the corresponding positive wire in the harness.
@@akidim13 Here's an update. The connectors are all the same. It worked on my TS. I did have to splice some wires but overall it took about 20 minutes to put both headlights in. The only pain in the ass was removing the bumper which is sadly necessary.
@@0yCrazyb cool bro I appreciate it , gonna get me them too, how you like them so far, also what wires did you have to splice ? Was it the daytime running lights one ??
![How To Retrofit Your 04/05 WRX/STI Headlights! [Full Walk-through]](http://i.ytimg.com/vi/oBgXV22Jy-0/mqdefault.jpg)
![How To Retrofit Your 04/05 WRX/STI Headlights! [Full Walk-through]](/img/tr.png)
@jasonmangila The high beam on the headlights are generally fixed. However, you still have the option to adjust them to the height desired. Thanks and good luck.
These also come with brackets that you needed to fit onto your vehicle. did you miss that? if anything, please review this video again to see if you have missed anything.
You have to splice the halo and led wires to your running lights. one positive one negative for each
Yes.. there should be screws located behind the housing to adjust it
It is impossible to adjust when installed on the vehicle. The adjustment bolts are not accessible when installed on tye vehicle.
@jasonmangila Almost all the projectors have a screw in the back that can help you adjust the low beam. There will be either two or four. For up down left right. Please check with your selling to make sure. Thanks and good luck
wire your halo and led wires together, if your LEDs are working, go ahead and splice your halo wires into your led wires.
Been looking for this answer lol😂thanks!!!
@minhsteve09 Thank you , we agree, they did come out a lot nicer than expected.
Why the 3 leds in the middle, throws the look completely off. Then for the hawkeye yall make the lights perfect.
apologies on that, you are correct sir. but unfortunately we do not have an aftermarket tail lights on our website so therefore we couldn't give you a correct answer.
but yes, the only difference from 02-04 and 06-07 are the face-lifts and pre-face lifts. tail lights are about the same unless you are driving the wagon
Would love to see a light adjustment video for these lights.
Just broke one due to lack of knowledge
How did you do it buddy? I'm trying to do this as we speak!
Same
@AbhLafiel yes our video's are mainly for people that want to DIY. but we strongly recommend consulting a body shop for professional installation
Once you take out your old headlights you wont have the ballast anymore so technically you wont have the factory HID's anymore. So yes youll be fine with these headlights.
@SuperRoscoe666 Sir, we do remind everyone that there is a separate installation instructions on how to wire your halos and leds, it is stated in middle of the video. our installation instructions do not provide that also.
There are screws behind the housing of your headlights to adjust your beams. Not sure if high beams will have them tho.
this set is exactly what I want on my wrx, but after watching this video I see how much work is required. Based on my resources I know this would be a big pain and would just have to take it somewhere to be done for me.
This dudes video showed wayyy too many steps at the beginning, only thing you have to do to install the lights is to take off the grill and you can remove both headlights and replace them
Whoever decided it was a great idea to use H3 and H1 bulbs for the design is an idiot. They're primary FOG LIGHT bulbs.
I agree.. I'm not ire when the previous owner pit these one but the lenses are yellowed and textterd. H1s are a pain to change.. why not just use the factory style bulbs
It's not ricing at all I think, but what do I know? They look awesome!
What size are the leds in the halo and the three top led lights?
Thanks, you help me out alot
I'm sure these will perform much better than stock, but aesthetically IMHO these are rice. the 3 LED's above the low and high beam? For what? And not 1 pair but 2 pairs of angel eyes? I've looked for a nice set of prjectors since 05' and I haven't found one yet
@Specdtuninginfo ok thanks also something i should of ask was about the high beams as well was, are these fixed like the stock assembly? not sure how high beams are aimed where your from?
Aside from the lo-beam harness having to be moved from the stock lights to the new ones, do these halos require any additional wiring to be done?
she is so beautiful.
NO, theres a reason why they give you a specific year because of fitment.
The only way to actually make it fit is if you can convert your 02-04 to an 06 and rewire.
I'm sure you felt the same way about Euro Clears when they atarted popping up everywhere.
the oem turn signals have 4 pins when you turn to lock them in and the aftermarket ones only have 3? do i have to order different ones or am i dumb
Ok I'm planning in getting these lights for my 05 Sti. My question is my car comes with HIDS. What bulb comes with the low beam are they gonna be able to handle the power from my stock HIDS ?
had those lights WOW THE BIGGEST shits i ever bought.
I'm thinking of getting these. Why are they so bad? I don't want to waste my money on trash.
Still can't find the relay harness hid install video. My projectors only work on high beam....low beam are highs...even swapped the 2....
Great thanks for your feedback!
Is there another hole for parking lights, because compared to factory lights again the parking orange light is located in that exact place where the indicator hole is.
This may be a silly question but are these headlights more designed for LHD, RHD or can work effectively in both WRXs. I am considering these, but thought i'd ask first.
It depends on the Web sites you get them from, the one I got them from, since it was local to me sold them in RHD, so just check the description to be safe
Is it possible to change color on the angeleyes with another bulb? :-)
5:25 what did you do with yhe black and white wire on the bottom?
How does one go about replacing the 3 little led bulbs per headlight? What's the part number or bulb type and size? Tha j you. 2 of mine finally burned out
I can't find which harness I need to remove from the OEM assembly on 04 STI. Any assistance would be appreciated.
I have just bought these lights,the leds dont replace the indicators if you pause it at 8.26 you can see the indicator holes in the far corner, I have silva tec bulbs which appear silver but flash orange
are these headlights adjustable? up down left right?
Hello *****
Yes you should see some phillips head screws, they will help you adjust the projector headlights.
How did you get the light inside the halo on the outer sides of the light to be white like the others ?
Hello! I have a question about the turn signals.
On the OEM headlights, the turn signal is that orange section in the top middle. With these halo lights, the 3 LED's take the place of that section. My question is, are the 3 LED's the turning signal on these halo headlights? Also, will the turn signal with the new headlights be orange? In all the photos and videos I have seen, the 3 LED are illuminated white. Please let me know. Thank you in advance!
I need to know where are the adjustment screws I can't find them?
Are these illegal?
I bought these lights for my 2005 Sti, which was said was compatible with. I attempted to install and none of the plastic clips from the new headlights would fit with the ones on my car. Am I overlooking something?
Can these housing handle 6000k Hid bulbs, I bought these and they came with hids and ballasts, and I'm curious if they will go good together and be able to handle it?
can the low beam projectors be aimed for different countries???????
in order to replace your headlights
so I bout a 02-04 subaru tail lights and I was woundering would it fit my 06 wrx? And if it doesnt fit is there a way I can make it fit? please reply!
The bolts at 5:13 what are they called, I need to order a set.
These are halogen projectors right?
amazing how hard it is to find projector headlights for the 04-05 wrx WITHOUT those darn tri-LED things. AB-SOLUTELY ANNOYING. considering getting eyebrows with these. otherwise i have seen these as a great product! btw does anyone know what size HID bulb these take?
Did you do a full HID conversion or was it just plug and play??
R Rod No HID's were installed. The headlights are equipped with H1 halogen bulbs. The high and the low beam are a simple plug and play. You will need to wire the halo and LED bulbs to your daytime running lights.
Do these fit/work on an 05 2.5rs?
Hello consult the black and white cable of the angel eyes where I connect, since in the video tutorial do not show that
Michael did you figure it out yet?
Where do the black & white wires go????????????????????
Hi,
The black and white cables are for the HALO and/or LED lights in the headlights. You would have to splice and then tap them into the corner light harness or low beam harness to the corresponding wires. The black/negative wire should be tapped to a corresponding negative wire in the harness and the white/positive wire should be tapped into the corresponding positive wire in the harness.
Where are the turn signals? they got replaced with that led strip?
Do u have to remove front bumper to change the park light globe ?? Does anyone no ?
Paul Wynne no
@WarMonkey99 wow lmao headlights dnt make a car look like a ricer!
What is that tool called that was used to pry those tabs??
just use a screwdriver
The bulbs are propitiatory so i dont believe so.
WHY TAKE THE FRONT BUMPER OFF DID MINE WITH OUT TAKING FRONT BUMPER OFF HE`S HEAVING A LAUGH
iF YOU plan on buying those expect to replace every year
I'm thinking of getting these, why would you need to replace them? Are they made very cheaply?
@@bradleykindness3080 the angel eyes burn out, just after the warranty of 30 days
Does this work for the TS WAGON? (2004)
Literally about to ask this too
@@akidim13 Here's an update. The connectors are all the same. It worked on my TS. I did have to splice some wires but overall it took about 20 minutes to put both headlights in. The only pain in the ass was removing the bumper which is sadly necessary.
@@0yCrazyb cool bro I appreciate it , gonna get me them too, how you like them so far, also what wires did you have to splice ? Was it the daytime running lights one ??
@@akidim13 Theres a black and white wire for the halos. The running lights. All of the OEM bulbs will fit properly
@@0yCrazyb I’m gonna buy these now thanks! Couldn’t find anywhere online that said if they fit the 04 ts wagon