Really a good work. A ported 4TL100 (as per the port dimensions of 4TL10) has a better acceleration than 4TL10. Please post a video about where they do lathe work, tinkering, painting and plating in a single place in Thamizhnadu if you find one (exclude the greedy restoration persons). I need a 'one-place-shop' where all are done in the same shop or same person/shopkeeper who takes responsibility of all these things, because I don't want to wander for all the bikes. One more important thing: please check with any lathe person whether is it possible to remove the liner/factory-sleeve completely and insert a new liner (instead of sleeving) in case of a TVS-SUZUKI cylinder, because my cylinder's inner sleeve as well as outer one are broken and the crack extends upto the snout, which is because the previous owner had given it to some inexperienced labour, for sleeving.
Thanks! Unfortunately, I am yet to find an all in one shop that does all the things you said. Everything has its own seperate place and seperate set of people. Regarding the sleeve, I think you can talk to Darshan directly about it, he'll be able to clarify your doubt properly.
@@BrattyBiker Can you please share his contact details, address ? I am from Maharashtra Raigad district, so it will be better for me. I have 1990 RX 100 and one spare block. Thanks 🙏
I'm not sure, please contact Darshan & enquire. You can find it in the description box. I think it'd be better if you send him an old original block instead of a duplicate one but check with him & decide.
Sorry, I cannot reveal the cost. But I can say its much cheaper than going for an 'unsleeved' std size block but more expensive than your typical resleeving job.
bro my rx135 4spped does 110-120 but with super vibrations and it cruses at 65-70 are there any ideas to make the crusing speed upto 80-85 and also its idleing is also a headache it incrweases with engine heating and reduces with cooling of engine is there any idea to make it more consistant btws it has been semi ported (exhaust port) and has a self made inbuilt chamber ........will appreciate any response😃
No disrespect, but I think your chamber is mainly the culprit. Please use stock exhaust, use a stock block that's not ported, use 16 34 sprocketing, make sure your carburettor is OE without having any leaks or dirt as well & your issue will be solved :)
Thanks, unfortunately I cannot reveal the exact cost, it is much cheaper than going for std size 5 speed block, but more expensive than most local resleeving services.
Thank you... Bro actually I need your assistance... I have a Yamaha libero 2006 model bike .. Bike sound is like Honda unicorn... And it gives like gada gada .. type of sound .. Actually libero gives a smooth pleasent sound .. Even tho I gave for full bore still the sound is not changed ... If i want to get original company sound What are all the parts do I need to change Like bore kit, crankshaft etc. Please suggest me ...
Sir I'm converting 135 4 speed to 5 speed. I changed it to 5 speed cylinder but using the old head (4tl00). Is it okay to use the same or do I need to replace it asap?
Get some packing material, pack it properly, write & paste to & from adress, send it via India Post/Courrier service. It'll reach him in a few days & he can get the work done for you.
Darshan is very a sweet chap. Just contacted him and he resolved my all queries. Couldn't thank you much @brattybiker i was having problems with my 89 rx100 engine & gonna get em fixed by Darshan 😁
ruclips.net/video/pydXD_-tPD8/видео.html
Resleeving information
I know Dharshan personally... nice guy & a gr8 bike enthusiasts...
Oh yes, great guy! He gifted me the Shogun handlebar, which has become my favourite for the RX
Hi, could you please share the performance with this cylinder. Like millage, pick up, sound.
Sure, yet to install and run. Will report back with a seperate video.
Due to the agressive ports, I expect a mileage of 20kmpl but great performance.
Lets call this.. Brand new😁❤🙌🏻 love from kerala😍
Ofcourse ❤️
I have ported the block of Rxg only it’s outlet but it’s top speed only 100 last
Really a good work.
A ported 4TL100 (as per the port dimensions of 4TL10) has a better acceleration than 4TL10.
Please post a video about where they do lathe work, tinkering, painting and plating in a single place in Thamizhnadu if you find one (exclude the greedy restoration persons). I need a 'one-place-shop' where all are done in the same shop or same person/shopkeeper who takes responsibility of all these things, because I don't want to wander for all the bikes.
One more important thing: please check with any lathe person whether is it possible to remove the liner/factory-sleeve completely and insert a new liner (instead of sleeving) in case of a TVS-SUZUKI cylinder, because my cylinder's inner sleeve as well as outer one are broken and the crack extends upto the snout, which is because the previous owner had given it to some inexperienced labour, for sleeving.
Thanks!
Unfortunately, I am yet to find an all in one shop that does all the things you said. Everything has its own seperate place and seperate set of people.
Regarding the sleeve, I think you can talk to Darshan directly about it, he'll be able to clarify your doubt properly.
@@BrattyBiker thank you
@@Anandkumar-hz8mn Cheers!
Is Dharshan's garage in Tamil Nadu/Kerala/KA?
Never mind, it is in MH.
Yes, Bhiwandi.
@@BrattyBiker Can you please share his contact details, address ? I am from Maharashtra Raigad district, so it will be better for me. I have 1990 RX 100 and one spare block. Thanks 🙏
Sorry ..found in your video description 😃🙏
@@devendrabagul6613 No problem, hope it helps :D
Can you give matchin workshop detels?
Bro can we porting on sleeved block
Bro npp or top pro which is better piston
big fan bhai apse 1 sawal hein
rxg 135 or rx135 kiya alag version hein
ya rxg 135 or rx 135 same hein.
RXG came before 135. Same engine as 135, but the magnet coil, primary gear clutch bell & chain sprocketing were different.
How much cost
How much cost for resleved
Will the seleeve get loose while heating
Nope. I'm running it on my bike currently, did a 1100km highway round trip with full throttle for long periods and absolutely no issues.
Nice vedio bro good information 👍👌
Thanks :D
Can we installed with a new sleeve again an again after the last stage of piston no.
Not really. Everytime you want to insert a sleeve, the block has to be honed, beyond a point, the sleeve will be too loose.
@@BrattyBiker ok thank you for the suggestions will be I n touch in with you when ever I got problems
Is the sleeve an Indonesian import?
No, it's made locally in India. Btw, Yamaha doesn't sell sleeves seperately, because it is not press fit, the cylinder is cast around the sleeve.
Bratty bro waiting for your restoration video 😍😍😍
Thanks bro, coming soon :D
What is the best sleeve for 5speed?
Give it to Darshan.
For a new cast iron sleeve to be installed inside the original cast iron bored sleeve, what is the interfearance fit in microns?
Very good question, something I don't know the answer of. I think it depends on who is doing it on what block & what sleeve.
@@BrattyBiker I feel it should be between 0.035 upto 0.055 mm interfearance fit considering cast iron being prone to cracks under stress.
That's cool, thanks for the info!
friend what about goetze cylinder kit pls reply
I'm not sure, please contact Darshan & enquire. You can find it in the description box.
I think it'd be better if you send him an old original block instead of a duplicate one but check with him & decide.
How much cost for this sleeve ?
Sorry, I cannot reveal the cost. But I can say its much cheaper than going for an 'unsleeved' std size block but more expensive than your typical resleeving job.
bro my rx135 4spped does 110-120 but with super vibrations and it cruses at 65-70 are there any ideas to make the crusing speed upto 80-85 and also its idleing is also a headache it incrweases with engine heating and reduces with cooling of engine is there any idea to make it more consistant btws it has been semi ported (exhaust port) and has a self made inbuilt chamber ........will appreciate any response😃
No disrespect, but I think your chamber is mainly the culprit. Please use stock exhaust, use a stock block that's not ported, use 16 34 sprocketing, make sure your carburettor is OE without having any leaks or dirt as well & your issue will be solved :)
Good stuff, What was the cost of this job at your friend's place?
Thanks, unfortunately I cannot reveal the exact cost, it is much cheaper than going for std size 5 speed block, but more expensive than most local resleeving services.
Bro can a E-1 4TL00 head fits YP-1 Cylinder kit?
Yes.
Bro rx135 reed value change pannanum but price High so rx100 reed 135 la podalama edchai drawback varuma
No problems, they are the same reeds. Don't change it if your current reeds are clean and are sealing fine.
Ok Thanks Bro
Cheers!
Thank you... Bro actually I need your assistance...
I have a Yamaha libero 2006 model bike ..
Bike sound is like Honda unicorn...
And it gives like gada gada .. type of sound ..
Actually libero gives a smooth pleasent sound ..
Even tho I gave for full bore still the sound is not changed ...
If i want to get original company sound
What are all the parts do I need to change
Like bore kit, crankshaft etc.
Please suggest me ...
Sorry sir, absolutely no idea. I'd suggest you get it rebuilt properly.
Piston sleeve is which quality?
It looks & feels high quality. Material used is cast iron & thickness is 4mm.
Sir I'm converting 135 4 speed to 5 speed. I changed it to 5 speed cylinder but using the old head (4tl00). Is it okay to use the same or do I need to replace it asap?
It's OK to use the same, but the 5 speed head will net you better performance as it is for higher compression.
Hey bro you do really information vlogs and I think you can do it tamil as many don’t do such vlogs in tamil❤😅
Thanks, I wanted to do everything in English so that the channel will have a better reach. Shall occassionally make something on Tamizh :)
How to send to darshan
Get some packing material, pack it properly, write & paste to & from adress, send it via India Post/Courrier service. It'll reach him in a few days & he can get the work done for you.
Hi bri
Can u make a new sleeve for my shogun cylinder. And where s your garage.
Please contact Darshan, he is located in Thane, Mumbai. He can help you give new life to the Shogun block!
Bro any problem if put 4ah battery in rx135 .
Or 2.5 ah is better.
Extra fog lights is need using
No idea bro. People cut the air filter box to accomodate bigger batteries, I would not do it. It puts extra load on the entire electrical system.
Bro what material was used for sleeve, iron ?? If it is iron it will over heat quickly
Yes, cast iron, just like the factory block.
This is Indonesia make cylinder
No. Indian cylinder
Sleeve is succsess or not
Very much a success. Running it right now, satisfied with the performance. I still need to perfect the jetting, but midrange is excellent.
Number of dharshan
Kindly given me darshan garage full address with contact number i am from Kolkata....so i send him my rx100 block
The contact details are in the description box of this video :)
Darshan is very a sweet chap. Just contacted him and he resolved my all queries. Couldn't thank you much @brattybiker i was having problems with my 89 rx100 engine & gonna get em fixed by Darshan 😁
Cheers! Hope it gets resolved :)
Contact number plz
You can contact me via Instagram : @brattybiker.
Darshan's contact number is present in the video's description below.