This is very poor job of re-sleeving a cylinder head, the actual process is very different bcz it involves heating the cylinder and shrinking the sleeve with cold it takes a precise amount of calculation and almost ration of heat and cold for re sleeving cylinder and perform effectively.
Nooooooo You must warm the cilynder and male the sleeve col. Than it will go inside with free play to align. In just 5 second than you align the port.. Why this people don t sue the head...
OMG No! No! that sleeve is so loose it will not be able to dissipate its heat to the cylinder for cooling, and the worst is that sleeve will "Walk" and push out the head gasket. please nobody do this its a hack butcher job. great installation information can be had from either LA Sleeve or my boys at Advanced sleeve around the corner.
Sleeve installation kay baad kesi performance hoti hy RX115 ys 135 ki. Kuch loog kehtay hein 2stroke mein sleeve successful nahi rehti pick aur power mein faraq aajata hy. Aur piston bhi seize hota hy
This is very poor job of re-sleeving a cylinder head, the actual process is very different bcz it involves heating the cylinder and shrinking the sleeve with cold it takes a precise amount of calculation and almost ration of heat and cold for re sleeving cylinder and perform effectively.
Absolutely
Nooooooo
You must warm the cilynder and male the sleeve col.
Than it will go inside with free play to align.
In just 5 second than you align the port..
Why this people don t sue the head...
OMG No! No! that sleeve is so loose it will not be able to dissipate its heat to the cylinder for cooling, and the worst is that sleeve will "Walk" and push out the head gasket. please nobody do this its a hack butcher job. great installation information can be had from either LA Sleeve or my boys at Advanced sleeve around the corner.
Wrong method.fitment also loose
എന്ത് തേങ്ങാ ആണ് ചെയ്യുന്നേ ഇങ്ങനെ ആണോ sleeve ചെയ്യുന്നേ. അപ്പോൾ കുറെ കാലം കിടക്കും.
Once sleev is last over size what's next
Can i use that block or not
not
How much it does cost
Sleev cost 1500
@@surajliferocks I want to put new sleeve on my 5speed block It will be alright?
Where is this shop?
Sleeve installation kay baad kesi performance hoti hy RX115 ys 135 ki. Kuch loog kehtay hein 2stroke mein sleeve successful nahi rehti pick aur power mein faraq aajata hy. Aur piston bhi seize hota hy
Port matching ho toh kuch problem nahi hoti hai
@@rishigovekar1419 right
@@rishigovekar1419yes a 💯 right
Thank you 💛
Bro Yamaha RX100 bike la sleved and unsleved yaepadi kandu pudikaradhu konjam busy. Very urgent.
Bore ulla porting pannirukanu pakanum bro
Suzuki shaolin cyinder port pannuma ?
No sir sleeve not available ...
Price
Ekdum badiya bro 👌👌👍
சூப்பர் bro
Tell us what's standard size and sleeve size
0.25 mm bro
@@Deepakgs-bu6mx if in micrometre it says 50.23mm then till what size ull do honing
@@akibkumbari3790 the next size will be 0.75
@@Deepakgs-bu6mx bhai agar 50 mm ka block size hai n oversize piston 0.25mm ka hai to aap isko kitta boring n honing karoge
@@akibkumbari3790 bhai standard size hai 0.25 agar honing karoge toh next piston size apko market mai 0.50 hoga
Ahh the good old swing press
Bro can you tell me what is the procedure of removing an old sleeve
heat it up in a oven and carefully tap it out with a block of wood
Nice work
Evolavu Aachi bro
How much cost bro
Super
🚮 Total waste job cleanly recorded on cam 🤣
Successful hota hai kya ye sleeve rx135 mei
Ha bhai sahi tarike se hoga to acha kam karta hai...original jaisa to nahi lekin dum hota hai
bro ethu avlo price bro sollunga en bike ku change pannanum
3800
Not a proper work.. Old process this is
Poor Sleev Work Pasting With Araldite
Bhaiya apna shop ka address batao
No perfection 😂😂
Murder done
Yamaha new bike 2002 chahiye kallu
Number bron
It's not successful
Full video post pannu ga bro
100 Persent saaf kam
number
Ggg
Tumhara number bhai