The only difference is of the life of the cylinder, other than that no much difference. Now I see people complain that Goetze blocks give bad pickup and all but that's an utter rubbish, pickup depends on many factors, like proper tuning of the carburettor, clean air filter, condition of clutch assembly and the pickup coil, clean spark plug, condition of sprockets, proper functioning of the 2Tpump and oil flow inside the cylinder, etc,. One more thing when it comes to Goetze cylinders is proper chamfering of the cylinder walls and ports using port maps and last but not least proper lapping of the piston and rings to be set properly and one thing to be mentioned if any of the things are not done perfectly the bike will not perform the way it should, which in my humble opinion ,a Good mechanic either from factory of Escorts Yamaha ( like in my case), or a trained mechanic can do. One more thing is strict following of the run in period once the cylinder is done and plugged in the bike. Believe me I am running two side by side one E2 and another Goetze. No difference; condition : all of the above mentioned things must be "PERFECT"
Hi bro ... Awesome video ... Will my bike pickup increase once I rebore my G4 from 0.50 to 0.75 I also have a spare goezte standard cylinder kit with me. What would you suggest should I rebore or install the new cylinder kit?
Hi how r u? I have a very different question for u. I have seen that my rx100 is very imbalanced, i.e. when the pillion is very heavy, all the weight shifts to the back and the front wheen hardly has any grip, the bike becomes very difficult to manoeuvre and the bike loses grip. It becomes impossible to climb steep ascents! Is there any way th shift the weight of the bike to front wheel so it will feel a lot confident to ride?
@@MotoGod Thanx for replying bro, but u didnt answer my question. What if the lenght of the rear fork is increased by putting a 2-3 inch longer fork of another bike, along with increasing the length of the chain & brake rod, putting another chain cover, extending the rear mudguard, etc. I think this will shift the weight of the pillion a bit in front of the rear wheel and increase a bit more weight on the front wheel! I hope u get what i mean to say. If u dont get it, c how dirt bikes r altered which r used to climb very steep inclines. I just mean to do the same but on a smaller scale. This alteration is not that major but if it is done correctly will make any rx very stable to climb uphill with pillion! Pls reply.
No if you increase the height of rear shocks and all other mods still with pillion the front wheel will pop up and if you do all these mods the bike loses stability.....(the frame is the issue we can't do anything) what ever you do still the weight won't distribute to front in rx
Broi u r telling like increase in piston size like .25 ,.50 , after some wear n tear of clylinder.it means increase bore size .then the cc and the hp of motorcycles increases ?? After changing piston from .25 to .50mm or more than that .and if so the entire character of the engine changes right?give some detail info power changes after piston change ?!!
Hello moto God I need your help.. Am a owner of rxg so my original E1 cylinder blok it's seem to have sleeveed till 2mm so can you please calculate it out and explain it to me whether there is an option to rebored again or go for second sleve Or go for a new cylinder block what will be the solution?
Hi, I am in process to bring my Old RX135 back to life. I had been searching for OEM Block, but failed. Can you tell me where exactly can I get this Sleeve and which are the best ones. I use to do a bit off roading can these sleeve installed block take the pressure.
Bro can i ask a doubt. My rx100 will go off bad if i run for a while. It wont go above 60kmph. I think when engine gets heat. That means my cylinder is sleeved? Cause the work shop guy told like these kind of power issues comes if the cylinder is sleeved. It doesnt hav any power
Don't listen to this puncture puttar, RXK carb is a direct fit to the rx135 and you can order it direct from Mikuni. The problem is jetting and if you don't happen to have a trained mechanic at hand, you can face a lot of problems. What I suggest is, get a properly trained mechanic and not a puncture puttar who claims to be a mechanic and try different jet sizes on your current carb. You can order different sized O.E jets from Mikuni. Don't ever use Natco or some other shitty brand jets in your existing carb. There is a reason Mikuni have existed for more than a 100 years. However I would suggest this upgrade only if you have ported your bore and have an upgraded CDI. To put it simply think of your mouth as your carburetor and your food pipe as your ports, if the ports aren't big enough no matter how much you put in your mouth, the food will be restricted by your food pipe.
Ji I didn't abt this till now, I should have watched it before giving it for sleeving. My mechanic made me to sleeve the bore it was only bored till 0.50,
@@mrkiinnu Don't listen to this idiot, Goetze and mahle are ok if its a 4 speed and you barely redline it. Always go for ART or Wiseco if you want performance and reliability.
He is ri8. Beware 2stroke lovers. Am stuck with sleeved cylinder on my kb125 (limited spare availability). Go for only Gud quality sleeve and piston or end up with piston seizure while running.
Don't listen to this idiot. Seizure only happens if your sleeve isn't pressed properly or if you have insufficient lubrication of if you have insufficient clearance between the bore and the piston and piston rings or if you have bad cooling or if the bore isn't honed properly or if you have metallic debris like rust from your fuel tank enter the combustion chamber. If all the above requirements are met then even the worst quality sleeves wont seize. The bore and piston will make a very rough noise but it won't seize. Again don't listen to this puncture puttar who doesn't know shit and is trying to preach people from the half baked knowledge he attained from another puncture puttar who thinks he is a certified mechanic.
Love From Bangalore ❤️ motogod 💥
Thanks
Wow! This is the first Indian Moto video that speaks English, Subscribed bro
Sir can the motorcycle perform the same power like previous condition after sleeving?
No it won't
Can you estimate the amount that cost for g-1 cylinder kit for rx100 in current year 2024
Bro plz tell about std size geotrz bore and piston for rx is best like yamaha new one ?? Plzz reply bro
The only difference is of the life of the cylinder, other than that no much difference. Now I see people complain that Goetze blocks give bad pickup and all but that's an utter rubbish, pickup depends on many factors, like proper tuning of the carburettor, clean air filter, condition of clutch assembly and the pickup coil, clean spark plug, condition of sprockets, proper functioning of the 2Tpump and oil flow inside the cylinder, etc,. One more thing when it comes to Goetze cylinders is proper chamfering of the cylinder walls and ports using port maps and last but not least proper lapping of the piston and rings to be set properly and one thing to be mentioned if any of the things are not done perfectly the bike will not perform the way it should, which in my humble opinion ,a Good mechanic either from factory of Escorts Yamaha ( like in my case), or a trained mechanic can do. One more thing is strict following of the run in period once the cylinder is done and plugged in the bike. Believe me I am running two side by side one E2 and another Goetze. No difference; condition : all of the above mentioned things must be "PERFECT"
@@sohamsinha3631 thank youbro
can we remove old sleeve and install new sleeve?
Yes
Hi bro ... Awesome video ... Will my bike pickup increase once I rebore my G4 from 0.50 to 0.75
I also have a spare goezte standard cylinder kit with me.
What would you suggest should I rebore or install the new cylinder kit?
Hi how r u? I have a very different question for u. I have seen that my rx100 is very imbalanced, i.e. when the pillion is very heavy, all the weight shifts to the back and the front wheen hardly has any grip, the bike becomes very difficult to manoeuvre and the bike loses grip. It becomes impossible to climb steep ascents! Is there any way th shift the weight of the bike to front wheel so it will feel a lot confident to ride?
I'm Good Bro 😇
Same Happens with all RX series
it happens with my 135 too
With pillion it Won't Feel confident to ride
@@MotoGod Thanx for replying bro, but u didnt answer my question. What if the lenght of the rear fork is increased by putting a 2-3 inch longer fork of another bike, along with increasing the length of the chain & brake rod, putting another chain cover, extending the rear mudguard, etc. I think this will shift the weight of the pillion a bit in front of the rear wheel and increase a bit more weight on the front wheel! I hope u get what i mean to say. If u dont get it, c how dirt bikes r altered which r used to climb very steep inclines. I just mean to do the same but on a smaller scale. This alteration is not that major but if it is done correctly will make any rx very stable to climb uphill with pillion! Pls reply.
No if you increase the height of rear shocks and all other mods still with pillion the front wheel will pop up and if you do all these mods the bike loses stability.....(the frame is the issue we can't do anything) what ever you do still the weight won't distribute to front in rx
Finally founded the video really thanks for clearing out ❤️❤️❤️❤️❤️❤️❤️❤️
God bless
Thanks bro
Broi u r telling like increase in piston size like .25 ,.50 , after some wear n tear of clylinder.it means increase bore size .then the cc and the hp of motorcycles increases ?? After changing piston from .25 to .50mm or more than that .and if so the entire character of the engine changes right?give some detail info power changes after piston change ?!!
FROM .25 TO .50 YOU WONT SEE MUCH DIFFERNCE BUT FROM .25 TO 2.25 THEN YOU WILL FEEL DIFFERENCE
Hi brother present iam used 1987 Rx in Y-1 cylinder used but sleeved in size in 1mm iam preparing re sleeved you have Any new sleeve
Hello moto God I need your help.. Am a owner of rxg so my original E1 cylinder blok it's seem to have sleeveed till 2mm so can you please calculate it out and explain it to me whether there is an option to rebored again or go for second sleve Or go for a new cylinder block what will be the solution?
Rx100 ki chassis me koi other bike ka engine fit kar skate hai
Hi, I am in process to bring my Old RX135 back to life. I had been searching for OEM Block, but failed. Can you tell me where exactly can I get this Sleeve and which are the best ones. I use to do a bit off roading can these sleeve installed block take the pressure.
Location ?
Sir mare pas rx100bike hay uska block pe abhi sleev 75no ka piston chal rahi hay .next time l can re sleev or not
Sleeve bore will give pickup plz reply bro
Bro sleeving cheyinchadam best aa Goetze cylinder kit konadam best aa
I don't Prefer Both Get Used Block.
@@MotoGod Tqs bro
HOW TO IDENTIFY CYLINDER KITS SIZE ?? ..PLEASE MAKE A VIDEO
Bro can i ask a doubt. My rx100 will go off bad if i run for a while. It wont go above 60kmph. I think when engine gets heat. That means my cylinder is sleeved? Cause the work shop guy told like these kind of power issues comes if the cylinder is sleeved. It doesnt hav any power
Get it Checked Bro
Check cylinder piston clearance
What about goetze cylinder kits for rx? Are they any good?
They are good only bro
you can use it but
don't expert the same quality like original once.
@@MotoGod hi
Bro please tell the standard size for rx100 bore and tell me what is next size to standard.
Tell beginning size to ending size
Is Rebore and sleeving both process are same?
Kindly advice what quality / material sleeve shud be and availability , any manufacturer reputed???
I don't have better information on that topic so kindly visit your nearest lathe and ask them ❤️
What about goetz block kit for rx100 , is it successful?
Yes it's good
Hi bro, will you please tell us about fixing RXK carb in rx135, also please tell us about the availability of carb
Direct Fit But Its Difficult to get one in india
Don't listen to this puncture puttar, RXK carb is a direct fit to the rx135 and you can order it direct from Mikuni. The problem is jetting and if you don't happen to have a trained mechanic at hand, you can face a lot of problems. What I suggest is, get a properly trained mechanic and not a puncture puttar who claims to be a mechanic and try different jet sizes on your current carb. You can order different sized O.E jets from Mikuni. Don't ever use Natco or some other shitty brand jets in your existing carb. There is a reason Mikuni have existed for more than a 100 years. However I would suggest this upgrade only if you have ported your bore and have an upgraded CDI. To put it simply think of your mouth as your carburetor and your food pipe as your ports, if the ports aren't big enough no matter how much you put in your mouth, the food will be restricted by your food pipe.
I want Rx100 curb
Hey moto God can we resleve again by removing the old sleeve
How could we know about sleebe while buying an old rx?!
check it by opening the bore or check it by your mechanic
I want one shogun sleeve, where got it bro, any possibility, which company make is good
Sorry bro I don't have sleeve dealers who can provide ......
Which are the parts i need to change to convert rx100 to rx 135 and how much milage can be achive plezz repllyy🙁🙁🙁🙁
Crank, con rod, bore, head, piston, wiring, CDI, coil plate assy, and magnet, sprockets, carb, manifold, power box,...
@@MotoGod bro u missed the rx 135 monogram thats major 😅😅😅
Can sleeve cylinder be rebore to 75 for rx. What r the chances of success.
yes you can .75
Bro do you know any good person who does sleeving of block rxz 135, do let me know.
Message me on Instagram (_motogod_)
Bro what about goetez bore is it good or not
G1 cylinder available uh bro?
No bro not available with me
Yes its available 25 size
@@MOHAN_BOXER mobile number pls
Hey bro, how much the original bore &Piston can cost for my suzuki samurai??
2k-3k
Thanks bro..😃
Bro if we installed sleeve in rx 100 bike oru mileage will drop or not bro
Ji I didn't abt this till now, I should have watched it before giving it for sleeving. My mechanic made me to sleeve the bore it was only bored till 0.50,
Hey bro , what size of piston comes before 1.25mm ...
1mm
U mean 1.00 is that correct?
That's why I said
Good info bro but I want to know which company is the best one whether it is goedge or scott
Goetze
@@MotoGod is sam company there bro
Don't know bro
@@MotoGod Thanks bro
@@mrkiinnu Don't listen to this idiot, Goetze and mahle are ok if its a 4 speed and you barely redline it. Always go for ART or Wiseco if you want performance and reliability.
Bro in rx100....if we sleeve the kit pick-up and milage will be dropped ah bro????
If you install a sleeve .... then you completely messed your cylinder block ...(don't do it)
@@MotoGod bro I am having some doubts bro.....I want to ask u.... How can I contact u bro..... Because I need to do engine work so only
@@MotoGod instagram?
I have a question sir
Oo thank you for this knowledge bro very helpful for my max 100 project i have 75 piston now machine tel me for sleeving
Bro I have rxg which cylinder kit will be best
I-1, I-2 series
which copny piston is beyter for shaolin
Goetze piston
@@MotoGod thanks broo
Bro i just restored my rx but in first gair not get pickup
Wait for first thousand kilometres
Good manufacture makes pistons to 1mm like goetze 🔥🔥🔥
Bro how many km we ride rx135 without break
Depends on how you ride it and on rider
@@MotoGod 60 km / hr speed bro
Yes you can ride it
Best channel for 2stroker..
Thanks for your support bro 😊
Bro what is the difference between rx100 and rx135
Cc is different and power output is different
Which is best for drive 100 km per day rx100 are Rx135
135
Hlo bro i have suzuki sholin but the bore size is 2.jk
Bro you have Shogun piston 1.25
Message me on instagram (_motogod_)
Ok bro
Then sir how to increase the cc of the bike...
Over size the cylinder to it's max then the CC Will bump up
K
@@MotoGod but in your vlog you told that it's not good.?? Shall I do boring ?? Or not
Bro you have a rx100 sleeve
Shogun cilynder kit available ah bro?
No bro not available for sale
Kaveri Spare parts Kolhapur may have aftermarket ones, check with them
Bro i need standard piston for rx100
Message me on Instagram (_motogod_)
Hai bro can i get std size shogun bore
By doing sleeve on rx100 can make mileage drop
No
Hi .bro I want Shogun standard bore
Good information bro👍.
Try to give other 2stroke bike information like jawa-yezdi kawasaki rd 350 😀
Sure bro I'll do it very soon
Thanks for suggesting it to Moto god.... i want to know see and know more about RD 350 👍😁
Sleeving cost??
I got RX100 I-2 new block 36L10 98cm3 old stock with yamaha box.. last week .. and as u said i paid alot 😭
Sleeve lagana ma kitna karch aya
Apporx 3500
Thanks for the detailed information.
thanks for knowledge
Bro post an video on
Video on ?
@@MotoGod on the banned dates of 2-stroke
Sure bro I'll do it very soon 😊
He is ri8. Beware 2stroke lovers. Am stuck with sleeved cylinder on my kb125 (limited spare availability). Go for only Gud quality sleeve and piston or end up with piston seizure while running.
Thanks bro 😊
And Thanks for sharing your thoughts
Anytime bro ✌️
Don't listen to this idiot. Seizure only happens if your sleeve isn't pressed properly or if you have insufficient lubrication of if you have insufficient clearance between the bore and the piston and piston rings or if you have bad cooling or if the bore isn't honed properly or if you have metallic debris like rust from your fuel tank enter the combustion chamber. If all the above requirements are met then even the worst quality sleeves wont seize. The bore and piston will make a very rough noise but it won't seize. Again don't listen to this puncture puttar who doesn't know shit and is trying to preach people from the half baked knowledge he attained from another puncture puttar who thinks he is a certified mechanic.
informative video make more such videos bro
Bro plz a video on rx z 5 speed plz
Sure bro very soon 😊
Informative vidio bro Thanx❤❤❤❤❤
Thanks bro for taking your time and commenting on the video
Really it means a lot for me 😊
Informative if you want to f**k up your bike.
Very good useful video.
Glad it was helpful!
Well English what u r education if don't mind
Degree drop-out
Good video very informative
Thanks bro 😊
Good video 👌😁
Thanks 😊
Thank you 💛
My rx 135making noice after slive
Nice 👍
Thanks bro 😊
Very good video 🙏
Thanks 😊
Thanks macha
👍👌
😊
Good brother
Thanks brother 😊
👍🏽❤️
❤️
If we installed sleeve our mileage will be dropped
Rx 100 G1 block standard size
❤️
Hi bro ☺️🙂
Hi bro 😊
Bhai hindi me bolo
Hindi me video banao
50piston he good &bad he
Hindi me bol
Sorry This Channel is all about English Content
🤮🤮🤮
Bro how to fix piston noise🥲🥲
Nice 👍
Thank you! Cheers!
Bro how to fix piston noise🥲🥲