Glad it was helpful. Lots of other bells and whistles on the radios, but most people seldom, if ever, use them. If you ever see new icons on the screen, or are having any problems operating, just go through all the menu options and make sure all the other stuff is turned off.
I just purchased a set of there radios, their great for my needs. Question: I’m having trouble getting them to talk to another UHV radio(PXTON) on the same channel. Am I doing something wrong? Appreciate the knowledge.
The FCC assigns the 22 frequencies used by all FRS/GMRS radios, but not all manufacturers assign those frequencies to the same channel numbers. Midland uses what is called the "Motorola Standard Channels" but perhaps your friend's radios are different. Try looking up the frequency channel assignments for both and compare, or transmit on one and keep switching channels on the other until you hear the signal. Also, make sure neither radio is using CTCSS or DCS tones. I have another video explaining CTCSS. Good luck!
Excellent video! However, the radio only works within a 1-2 mile range, contrary to the advertised 30+ miles, even when set to high. Are there any other tips?
Elevation is the single best way to increase range. The stated range on all radios is for a direct transmission between 2 radios with no topographic or man-made obstructions. A range of 1 - 2 miles in an urban area, or a very hilly/wooded area is pretty good. You will also get better range on high power, but elevation is still king. You can use the headset and raise the radio up with your arm like the Statue of Liberty - yes, even a few extra feet of height can make a difference. Also make sure you keep the antenna at a 90 degree angle to the ground, as not much energy is sent out from the top and bottom of the radio. Base/mobile radios are available with up to 50 watts power on channels 15 thru 22, but make sure you get a GMRS license from the FCC, Good luck!
that is G M R S side of the radio I link oi to a east coast repeter group and talk to chicago weekly my base put's out 45 watts going in to a60 watt repeter 10 miles away
Thank you very much for the video, I did not know how to configure the radios and you have explained it very well, I would only like to know what we turn off the functions BP and RB. Greetings from Mexico.
I'm glad the video was helpful! To turn the Key Beep and Roger Beep on/off press the MENU button seven times until you see "bP" on the screen, then toggle on or off (on is indicated by "on" and off by "oF") with the arrow buttons to turn the Key Beep on/off. Press one more time (while the menu is still flashing) and you will see "rb" on the menu screen. Toggle with the arrow keys to turn the Roger Beep on/off. Buena Suerte!
Great video - VERY HELPFUL AND TO THE POINT thank you - Could you show how easily remove cover to remove batteries -- we have had ours sitting on shelf and batteries low in one so replaced with 5 double a batteries ( the original battery is rechargeable will replace AA batteries with a replacement rechargeable Panasonic SJK111. ) -- ours is a Midland XtraTalk GXT785. They work GREAT.
Hey Ed: With the back of the radio facing you, remove the belt clip by sliding it up and out for easy access, then remove the Battery Cover by pressing down on the top center and sliding it down from the radio. If the batteries inside have been in a long time they may have leaked and swollen. If it is difficult to remove the battery cover you can gently push down on the cover for a few minutes until the back will release. A light tap on a tabletop might help as well, just don't bang on it too hard. For long term storage always take out the batteries, whether disposable AAs or the rechargeable pack. Good luck!
If you can't turn the options for Vox and Weather off through the normal Menu selections, try doing a factory reset by turning the radio off, and then hold down the Arrow Up button while turning the radio on. You will, of course, have to set up your menu selections and any CTCSS or DCS codes again. Good luck!
I do see some aftermarket headset mics that are listed as working for both Midland and Kenwood, but cannot guarantee a specific Kenwood 2 pin would work. Midland makes inexpensive branded models, and there are a variety of aftermarket offerings.
Thank you. Quick question. I'm confused how to select a channel or privacy mode for my two radios. The instructions inside weren't clear. I don't want anyone picking up my conversations.
Unfortunately, Privacy Mode isn't what you think it is. Watch this video for an explainer on CTCSS codes: ruclips.net/video/_9v0y0gDceM/видео.html. Good luck!
sorry that won't happen all the code does is it prevents other people from talking to you so thay only get to hear you hope this help's you understand how and why.
Great video! Our football officiating crew of 7 are using the Midland GXT 1000 any suggestions how to best set these radios for our use during games? Thank you!
Hey Chuck: Since you will all be in close proximity, I'd suggest using the lower power channels 8 thru 14 as they are less likely to be occupied by other traffic. You can also all use a common CTCSS code to further exclude any outside transmissions. If you find you need more power, stick to channels 1 thru 7, and avoid 15 thru 22. The higher channels 15 -22 allow up to 50 watts, and are also where repeaters will operate if there are any in your area. The odds of encountering other users is much higher on these channels. Good luck!
FRS and GMRS radios share the same frequencies. The FCC only requires a GMRS license if you are going to transmit at 5w or higher, so you could legally use the GXT1000s at Medium power without a license, or one person without a license could use their radio at Medium power while you, with your license, use it at high power on the same frequency. Remember, too, that one FCC GMRS license covers everyone in your household. Just make sure everyone follows the FCC guidelines for call sign IDs, etc. Good luck!
If you see "VOX" on the screen, upper left, that means you have voice activation turned on. Go through the menu until you see VOX and use the arrows to turn it off. If that doesn't work do a factory reset by turning the radio on while pressing and holding the arrow up button. Good luck!
Interesting. I just had a strange experience with my GTX. I installed batteries in one of mine and as soon as I turned it on, it began vibrating and buzzing. I turned it off and the buzzing and vibration continued. Until I took a battery out. Thinking maybe it was broken I put those batteries in a different GTX and immediately the same phenomena happened when I turned the unit on. Turning it off again had no effect, only removing the batteries did. I was thinking a short of some kind, then I thought what were the odds of 2 different units both developing the same short on the same day? So low in probability I decided to try different batteries. I got some more AAs and changed them. Both units now work perfectly with the different batteries. All 4 of the batteries that produced the phenomena appear to be standard AA Alkaline batteries. I have no idea why the first set of batteries produced the effect. I hadn't even known there was a vibration feature in a GTX.
No. They can be charged in the cradle, or by a mini jack that plugs into one of the side mic ports. They can take a while to charge, and if in the cradle do not leave them in there if it is unplugged. It will drain the batts. You can leave them always plugged in to the powered cradle, or take them out after fully charging. If they sit for a long time they will slowly discharge. Remove the batts if they will be unused and stored for a long period. Good idea to have an ample supply of AA Batts to use if you can't recharge with AC.
Hi Jackie! The GXT1000s have 50 "Channels" but there are really only 22 separate frequencies assigned to GMRS by the FCC. Midland loads the radio with additional Channels that are just the original frequencies with pre-assigned CTCSS or DCS codes. I don't know what is meant by 10.21, though. Perhaps your group uses both channels 10 and 21? The channels from 8 to 14 are limited in power to 0.5 watts, and are best used when the stations are in close proximity. Channels 1 to 7 have 5 watts maximum, and 15 to 22 have 50 watts max. Channel 21 would be a good channel to use for longer distances. To change channels you press the MENU button, then use the arrows to navigate to the channel you want to use. Press the PTT on the left side once you are on the desired channel. Hope this helps. Good luck!
I'm guessing that by subchannel you mean the CTCSS or DCS code your team is using. This would appear as a large number 10 with a smaller 21 to the bottom right. The 21 isn't really a subchannel, but is the CTCSS or DCS code that is programmed in to Channel 10. I have another video explaining CTCSS: ruclips.net/video/_9v0y0gDceM/видео.html If your car team is not transmitting over large distances, using Channel 10 should be fine. It is, however, limited to a transmit output power of 0.5 watts (this applies to channels 8-14). If you need greater distances try using channels 1-7 or 15-22. Good luck!
On the Midland GXT they group setting is you set ur radio to group 10 channel 10 and the ctcss or dcs tone you decide note anyone else can still hear you and the others you just won't hear them unless on the same group pl tone n radio
When I change the power output to “H” (on channel 16), and hit the PTT button to set it, it goes back to “L” power mode after I transmit. Why would it do that? Yes the unit is fully charged.
That's an odd one. Dows it happen if you just wait for the radio to exit the Menu on it's own after about 5 seconds of no button pushing? I'd try a factory reset if it persists: Turn the radio off, then power it back on while holding down the UP ARROW button. Good luck!
@@lcect Ok so I fixed the issue. I thought it was odd as well as the battery was showing a full charge however I don't think that was the case and after placing both units on the charger overnight, they are operating normally now. Crisis averted. :)
There’s also channels 8-14. Something like that ,which are the FCC controlled radio channels that you need a license to transmit. The channels automatically stay on low. You can’t manually change it
Hi June: It sounds like you have the Weather Alert function activated. When the radio is on it will monitor the National Weather Service NOAA All Hazards channel for any emergency alerts. To disable, hold the Menu button down until you get the WX (Weather) channel, then press the Menu button again to go into the selections. I believe the first one up is the Alerts (designated Al), and if it says "on" simply use the arrow buttons to turn it to "off". Then press the PTT button on the side to exit. Good luck!
Hi Carmen: Press MENU, then keep pressinguntil you are seeing "Gr" on the diplay. Use the arrows to toggle from "oF" to "on". Once you are in Groups Mode you can set the ID. Press MENU until you see the group numbers in the lower right of the display start blinking, then use arrows to select the Group Number. Press the PTT on the side to exit.
pick a channel for all radios place same ch in all radios then pick a code and do the same for all radios you are in the code prevent's anyone out side you group to talk to you have funn
Hey DaBomb: The rule of thumb is to use the lowest power necessary to make the contact, so the answer depends on how far apart the radios will be. If the distance is short, start with channels 8 thru 14, which are fixed at 0.5w. Choose a channel and listen for 30 seconds or so to make sure it isn't in use, then try to make the contact. If that doesn't work, move to a channel from 1 thru 7, which are maxed at 5w, and try the contact again. Channels 15 thru 22 allow for up to 50w, and are used by high power base stations and repeaters, so avoid those if you can because you are more likely to encounter interference. Handheld walkies only have 5w on these channels, and are not usually able to access repeaters. Make a comm plan - start on CH8, if busy move to Ch9, etc. If no contact on 0.5w, move to CH1, and if busy try Ch2, etc. If you can't make contact on CH1-7 with 5w, the radios are too far apart. Good luck!
@@lcect I was on a higher channel and a man got on and told me to get off …it was the sheriffs line … I told him prove it and he said he’ll trace the call and come to my house 😳
@weRweekendwarriors The FRS/GMRS frequencies are set aside by the FCC for use by the public, free of charge. Their only requirement is that people using the higher channels at more than 5 watts power must get a GMRS license. Public safety agencies do not use these channels - ever. Transmissions cannot be "traced" except by complex triangulation, called "foxhunts" that require two or more stations triangulating the location. Unfortunately, there are people out there who think they can claim a channel for personal use. They cannot. If someone is using a channel, common practice is to find another open channel, but nobody can tell you not to use a frequency.
Hi Denise: No, the Midland radios operate in the FRS/GMRS band which is a much higher frequency than the CB radio band. The lower frequency of the CB band makes them better at longer-range transmission, while the higher frequency of the FRS/GMRS band makes them better at getting around obstructions as in cities. The higher frequency of FRS/GMRS also means the antennas can be much smaller, as opposed to the very long antennas required for the CB radios.
Range varies depending on the power level used and the topography between stations. On high power in an urban setting with a lot of buildings and man made obstructions you can expect between 1/2 and 1 mile. In rural, flat areas you. Might get up to 5 miles. If both stations are at high elevations, with no line of sight obstructions, you could see much longer range. Elevation is the greatest asset for long distance propagation, especially if there is clear line of sight between stations. Urban settings and hill terrain will be the most difficult.
Hola Manuel: Es posible que su radio esté en modo monitor y el silenciador esté abierto. Mantenga presionada la tecla marcada "Mon/Scan" y vea si se cierra el silenciador. Si no cambio, apague la radio y vuelva a encenderla mientras mantiene presionado el botón de flecha hacia arriba. ¡Buena suerte!
If the radio is otherwise functioning normally try removing the battery and replacing it. If that doesn't work, power off the radio and then power it back on while holding the "Up" button. This will factory reset the radio. If the radio is not working normally look to see if any of the keys are stuck.
Keep pressing the MENU button until VOX is flashing on the screen, then use the ARROW UP or ARROW DOWN button to toggle it off. If for some reason it is stuck, turn the radio off and then turn it back on while holding down the ARROW UP button to do a factory reset of the whole menu.
A good trick to have in your bag is to do a factory reset by turning the power on while holding down the Arrow Up button. This is a quick way to clear settings that might be causing a problem. Good luck!
Hi, I have the yellow GXT-735 model, but the house current is 220v and the model has an American and not a European switch, I don't know how to charge the batteries
Your radio is manufactured for the US market, and will require 110v to recharge the NiMH battery. You can remove the NiMH battery and use 4 disposable AA batteries until you are able to get an adaptor for the charger. Good luck!
Great video. Good videography, concise, clear narration w good audio. No annoying music. Wish they were all this quick and to the point.
Much appreciated!
Great video. You made it so easy to get it going and explained the basics without complicated lingo. 👌👌👍Thank you
Simple and easy! Perfect for me! Thanks so much!
Way better than reading directions 😂👌 thankyah sir
Glad it was helpful. Lots of other bells and whistles on the radios, but most people seldom, if ever, use them. If you ever see new icons on the screen, or are having any problems operating, just go through all the menu options and make sure all the other stuff is turned off.
great video.. knew nothing about these radios..(how to talk) Now I do. Thank you very much!
This is what people want to see....well done
Thanks! Glad it was helpful.
thank you for this easy to understand guide!
This was just the video I needed to get started. Thank you for taking the time to make this video it is extremely helpful and simple to follow.
Glad it was helpful! Good luck on the air.
best video on RUclips on this topic
I like the video I thought it was very important also I have a Midland GTX extra talk thank you very much and I will keep in touch
I just purchased a set of there radios, their great for my needs. Question: I’m having trouble getting them to talk to another UHV radio(PXTON) on the same channel. Am I doing something wrong? Appreciate the knowledge.
The FCC assigns the 22 frequencies used by all FRS/GMRS radios, but not all manufacturers assign those frequencies to the same channel numbers. Midland uses what is called the "Motorola Standard Channels" but perhaps your friend's radios are different. Try looking up the frequency channel assignments for both and compare, or transmit on one and keep switching channels on the other until you hear the signal. Also, make sure neither radio is using CTCSS or DCS tones. I have another video explaining CTCSS. Good luck!
Excellent video! However, the radio only works within a 1-2 mile range, contrary to the advertised 30+ miles, even when set to high. Are there any other tips?
when you go to your g m rs side there is your 20 mile range when the radio is set on a repeter
tower then your at 20 miles with a license
Elevation is the single best way to increase range. The stated range on all radios is for a direct transmission between 2 radios with no topographic or man-made obstructions. A range of 1 - 2 miles in an urban area, or a very hilly/wooded area is pretty good. You will also get better range on high power, but elevation is still king. You can use the headset and raise the radio up with your arm like the Statue of Liberty - yes, even a few extra feet of height can make a difference. Also make sure you keep the antenna at a 90 degree angle to the ground, as not much energy is sent out from the top and bottom of the radio. Base/mobile radios are available with up to 50 watts power on channels 15 thru 22, but make sure you get a GMRS license from the FCC, Good luck!
that is G M R S side of the radio I link oi to a east coast repeter group and talk to chicago weekly
my base put's out 45 watts going in to a60 watt repeter 10 miles away
I run a 45 watt base and have no problum reaching the tower 10 miles away
I am licensed for g m r s
Thank you very much for the video, I did not know how to configure the radios and you have explained it very well, I would only like to know what we turn off the functions BP and RB. Greetings from Mexico.
I'm glad the video was helpful! To turn the Key Beep and Roger Beep on/off press the MENU button seven times until you see "bP" on the screen, then toggle on or off (on is indicated by "on" and off by "oF") with the arrow buttons to turn the Key Beep on/off. Press one more time (while the menu is still flashing) and you will see "rb" on the menu screen. Toggle with the arrow keys to turn the Roger Beep on/off. Buena Suerte!
@@lcect Thanks a lot for the explanation!!!
read the book that came with it
Great video - VERY HELPFUL AND TO THE POINT thank you - Could you show how easily remove cover to remove batteries --
we have had ours sitting on shelf and batteries low in one so replaced with 5 double a batteries ( the original battery is rechargeable will replace AA batteries with a replacement rechargeable Panasonic SJK111. ) -- ours is a Midland XtraTalk GXT785. They work GREAT.
Hey Ed:
With the back of the radio facing you, remove the belt clip by sliding it up and out for easy access, then remove the Battery Cover by pressing down on the top center and sliding it down from the radio. If the batteries inside have been in a long time they may have leaked and swollen. If it is difficult to remove the battery cover you can gently push down on the cover for a few minutes until the back will release. A light tap on a tabletop might help as well, just don't bang on it too hard.
For long term storage always take out the batteries, whether disposable AAs or the rechargeable pack. Good luck!
I can’t get rid of vox and the WI near the battery line and the LMH thingy …I’m trying to talk to my other walkie talkie but I can’t get through😢
If you can't turn the options for Vox and Weather off through the normal Menu selections, try doing a factory reset by turning the radio off, and then hold down the Arrow Up button while turning the radio on. You will, of course, have to set up your menu selections and any CTCSS or DCS codes again. Good luck!
@@lcect thanks I’ll try that !!
read the book that came with the radio
@@donalderickson-si8wwreally ? Is that what I’m supposed to do ? Gee thanks Sherlock
Can I connect a PTT with a Kenwood 2 pin? Or would I use a PTT with a Motorola 2 pin?
I do see some aftermarket headset mics that are listed as working for both Midland and Kenwood, but cannot guarantee a specific Kenwood 2 pin would work. Midland makes inexpensive branded models, and there are a variety of aftermarket offerings.
Thank you. Quick question. I'm confused how to select a channel or privacy mode for my two radios. The instructions inside weren't clear. I don't want anyone picking up my conversations.
Unfortunately, Privacy Mode isn't what you think it is. Watch this video for an explainer on CTCSS codes: ruclips.net/video/_9v0y0gDceM/видео.html. Good luck!
sorry that won't happen all the code does is it prevents other people from talking
to you so thay only get to hear you hope this help's you understand how and why.
Great video! Our football officiating crew of 7 are using the Midland GXT 1000 any suggestions how to best set these radios for our use during games? Thank you!
Hey Chuck: Since you will all be in close proximity, I'd suggest using the lower power channels 8 thru 14 as they are less likely to be occupied by other traffic. You can also all use a common CTCSS code to further exclude any outside transmissions. If you find you need more power, stick to channels 1 thru 7, and avoid 15 thru 22. The higher channels 15 -22 allow up to 50 watts, and are also where repeaters will operate if there are any in your area. The odds of encountering other users is much higher on these channels. Good luck!
Great information! Thank you!!@@lcect
set them on same channel drop a privet code so the fans wont interfear
Thank you! For the Midland GXT, do both users have to have a FCC License for GMRS. Pardon my ignorance on this.
FRS and GMRS radios share the same frequencies. The FCC only requires a GMRS license if you are going to transmit at 5w or higher, so you could legally use the GXT1000s at Medium power without a license, or one person without a license could use their radio at Medium power while you, with your license, use it at high power on the same frequency. Remember, too, that one FCC GMRS license covers everyone in your household. Just make sure everyone follows the FCC guidelines for call sign IDs, etc. Good luck!
@@lcect Thank you, I was looking at these as a reliable communication device for drivers in a one-mile relatively flat area. Again, great intro!
anyone operating on the G M R S side need's to be licensed to do so it's 35.00dollars
for 10 years
Question. For some reason, my radio communicates without the PTT button being pressed in. How do i disable that? Thank you in advance!
If you see "VOX" on the screen, upper left, that means you have voice activation turned on. Go through the menu until you see VOX and use the arrows to turn it off. If that doesn't work do a factory reset by turning the radio on while pressing and holding the arrow up button. Good luck!
Hello, i had a question, i push to talk and for some reason it makes a beeping noise everytime i tap it
Hi CG: Are you hearing the beep on the radio you are transmitting on, or on the receiving radio?
Interesting. I just had a strange experience with my GTX. I installed batteries in one of mine and as soon as I turned it on, it began vibrating and buzzing. I turned it off and the buzzing and vibration continued. Until I took a battery out. Thinking maybe it was broken I put those batteries in a different GTX and immediately the same phenomena happened when I turned the unit on. Turning it off again had no effect, only removing the batteries did. I was thinking a short of some kind, then I thought what were the odds of 2 different units both developing the same short on the same day? So low in probability I decided to try different batteries. I got some more AAs and changed them. Both units now work perfectly with the different batteries. All 4 of the batteries that produced the phenomena appear to be standard AA Alkaline batteries. I have no idea why the first set of batteries produced the effect. I hadn't even known there was a vibration feature in a GTX.
That's an odd one! If you have any future trouble try a factory reset by turning it off, then on again while holding the arrow up button. Good luck!
Is the charge cable for the X Talker a USB C?
No. They can be charged in the cradle, or by a mini jack that plugs into one of the side mic ports. They can take a while to charge, and if in the cradle do not leave them in there if it is unplugged. It will drain the batts. You can leave them always plugged in to the powered cradle, or take them out after fully charging. If they sit for a long time they will slowly discharge. Remove the batts if they will be unused and stored for a long period. Good idea to have an ample supply of AA Batts to use if you can't recharge with AC.
A must for shtf. Buy cheap ones to pass out to freinds in a shtf situation
Great video. My car group recommended this walkie using 10.21 channel. How do I program to this channel? Thank you so much.
Hi Jackie! The GXT1000s have 50 "Channels" but there are really only 22 separate frequencies assigned to GMRS by the FCC. Midland loads the radio with additional Channels that are just the original frequencies with pre-assigned CTCSS or DCS codes. I don't know what is meant by 10.21, though. Perhaps your group uses both channels 10 and 21? The channels from 8 to 14 are limited in power to 0.5 watts, and are best used when the stations are in close proximity. Channels 1 to 7 have 5 watts maximum, and 15 to 22 have 50 watts max. Channel 21 would be a good channel to use for longer distances.
To change channels you press the MENU button, then use the arrows to navigate to the channel you want to use. Press the PTT on the left side once you are on the desired channel.
Hope this helps. Good luck!
I will double check with someone else from the car group. It might have been a typo. Thank you.
Mystery solved. It’s channel 10 subchannel 21.
I'm guessing that by subchannel you mean the CTCSS or DCS code your team is using. This would appear as a large number 10 with a smaller 21 to the bottom right. The 21 isn't really a subchannel, but is the CTCSS or DCS code that is programmed in to Channel 10. I have another video explaining CTCSS: ruclips.net/video/_9v0y0gDceM/видео.html
If your car team is not transmitting over large distances, using Channel 10 should be fine. It is, however, limited to a transmit output power of 0.5 watts (this applies to channels 8-14). If you need greater distances try using channels 1-7 or 15-22. Good luck!
On the Midland GXT they group setting is you set ur radio to group 10 channel 10 and the ctcss or dcs tone you decide note anyone else can still hear you and the others you just won't hear them unless on the same group pl tone n radio
When I change the power output to “H” (on channel 16), and hit the PTT button to set it, it goes back to “L” power mode after I transmit. Why would it do that? Yes the unit is fully charged.
That's an odd one. Dows it happen if you just wait for the radio to exit the Menu on it's own after about 5 seconds of no button pushing? I'd try a factory reset if it persists: Turn the radio off, then power it back on while holding down the UP ARROW button. Good luck!
@@lcect Ok so I fixed the issue. I thought it was odd as well as the battery was showing a full charge however I don't think that was the case and after placing both units on the charger overnight, they are operating normally now. Crisis averted. :)
There’s also channels 8-14. Something like that ,which are the FCC controlled radio channels that you need a license to transmit. The channels automatically stay on low. You can’t manually change it
Why is my gxt Midland has a cloud flash how do you stop it
Hi June: It sounds like you have the Weather Alert function activated. When the radio is on it will monitor the National Weather Service NOAA All Hazards channel for any emergency alerts. To disable, hold the Menu button down until you get the WX (Weather) channel, then press the Menu button again to go into the selections. I believe the first one up is the Alerts (designated Al), and if it says "on" simply use the arrow buttons to turn it to "off". Then press the PTT button on the side to exit. Good luck!
How do I select a group number and ID number?
Hi Carmen: Press MENU, then keep pressinguntil you are seeing "Gr" on the diplay. Use the arrows to toggle from "oF" to "on". Once you are in Groups Mode you can set the ID. Press MENU until you see the group numbers in the lower right of the display start blinking, then use arrows to select the Group Number. Press the PTT on the side to exit.
pick a channel for all radios place same ch in all radios then pick a code and do the same for all radios you are in the code prevent's anyone out side you group to talk to you have funn
What's the best channel if you have 2 walkie talkies only?
Hey DaBomb: The rule of thumb is to use the lowest power necessary to make the contact, so the answer depends on how far apart the radios will be. If the distance is short, start with channels 8 thru 14, which are fixed at 0.5w. Choose a channel and listen for 30 seconds or so to make sure it isn't in use, then try to make the contact. If that doesn't work, move to a channel from 1 thru 7, which are maxed at 5w, and try the contact again. Channels 15 thru 22 allow for up to 50w, and are used by high power base stations and repeaters, so avoid those if you can because you are more likely to encounter interference. Handheld walkies only have 5w on these channels, and are not usually able to access repeaters.
Make a comm plan - start on CH8, if busy move to Ch9, etc. If no contact on 0.5w, move to CH1, and if busy try Ch2, etc. If you can't make contact on CH1-7 with 5w, the radios are too far apart. Good luck!
@@lcect alr that makes sense. Thanks! 🙏
all 22 channels will work for you
@@lcect I was on a higher channel and a man got on and told me to get off …it was the sheriffs line … I told him prove it and he said he’ll trace the call and come to my house 😳
@weRweekendwarriors The FRS/GMRS frequencies are set aside by the FCC for use by the public, free of charge. Their only requirement is that people using the higher channels at more than 5 watts power must get a GMRS license. Public safety agencies do not use these channels - ever. Transmissions cannot be "traced" except by complex triangulation, called "foxhunts" that require two or more stations triangulating the location. Unfortunately, there are people out there who think they can claim a channel for personal use. They cannot. If someone is using a channel, common practice is to find another open channel, but nobody can tell you not to use a frequency.
👍
Are they CB ?
Hi Denise: No, the Midland radios operate in the FRS/GMRS band which is a much higher frequency than the CB radio band. The lower frequency of the CB band makes them better at longer-range transmission, while the higher frequency of the FRS/GMRS band makes them better at getting around obstructions as in cities. The higher frequency of FRS/GMRS also means the antennas can be much smaller, as opposed to the very long antennas required for the CB radios.
What is the range up to on the walkie talkies
Range varies depending on the power level used and the topography between stations. On high power in an urban setting with a lot of buildings and man made obstructions you can expect between 1/2 and 1 mile. In rural, flat areas you. Might get up to 5 miles. If both stations are at high elevations, with no line of sight obstructions, you could see much longer range. Elevation is the greatest asset for long distance propagation, especially if there is clear line of sight between stations. Urban settings and hill terrain will be the most difficult.
ALL F R S radio's have a 2 watt transmiter it is for short range 2 miles communition's
yes 1 mile or line of site in the country you may get 2 miles
Mi radio tiene en la pantalla las letras RX y suena como interferencia siempre
Hola Manuel: Es posible que su radio esté en modo monitor y el silenciador esté abierto. Mantenga presionada la tecla marcada "Mon/Scan" y vea si se cierra el silenciador. Si no cambio, apague la radio y vuelva a encenderla mientras mantiene presionado el botón de flecha hacia arriba. ¡Buena suerte!
How do I turn off the weather mode?
Just press the PTT button on the left side of the radio.
read the book it will tell you everything
back light on screen won't turn off
If the radio is otherwise functioning normally try removing the battery and replacing it. If that doesn't work, power off the radio and then power it back on while holding the "Up" button. This will factory reset the radio. If the radio is not working normally look to see if any of the keys are stuck.
Now how do I get the vox of that why I’m here lol
Keep pressing the MENU button until VOX is flashing on the screen, then use the ARROW UP or ARROW DOWN button to toggle it off. If for some reason it is stuck, turn the radio off and then turn it back on while holding down the ARROW UP button to do a factory reset of the whole menu.
Uhm one is collecting static till sending something and the other will not receive anything. Their on the same channel. What now
Nevermind they finally worked together lol
Thanks for everything
A good trick to have in your bag is to do a factory reset by turning the power on while holding down the Arrow Up button. This is a quick way to clear settings that might be causing a problem. Good luck!
Men
Nothing on how to insert the headset into your head... Nice!
open the flap on the radio and look should be a large port and small port match them up
This doesn’t show anything
read the book it will explain everything
@@donalderickson-si8wwI did. Book is trash too.
User friendly? No.
Hi, I have the yellow GXT-735 model, but the house current is 220v and the model has an American and not a European switch, I don't know how to charge the batteries
Your radio is manufactured for the US market, and will require 110v to recharge the NiMH battery. You can remove the NiMH battery and use 4 disposable AA batteries until you are able to get an adaptor for the charger. Good luck!
@@lcect Thank you :)
or go to your locial battery shop buy your rechargeable batterys
and two wall charger's charge over night in stall and go