-opens gearbox on the wrong side. -uses tacky grease. -lowers the air volume with a faucet washer. -dosent check air nozzle compression -glues it on the cilinder head, it actually goes behind the piston head. -greases the anti-reversal latch. -dosent shim the gears. -dosent lube the piston nor the piston rails. -overtorques the crap out of the screws 😂
tbh this is an easy way to destroy your gearbox. He throws in new gears, every gear is has different tolorances even when they're the same brand. Go watch TheAirsoftTech on how to shim.
I think you opened the gearbox upside down, it seemed to work but that's at high risk of the tappet or and spring ready part to fling out and either mess up an already shimmed gearbox or just shoot things all over the place
Please for the love of god and all things good in this world like airsoft, DO NOT DO ANYTHING YOU SEE IN THIS VIDEO TO YOUR GUN. Some of the worst advice and worst work I have ever seen. Literally everything he did was wrong and miss information. The title of this video should be ”how to brake your pew in 13:1 steps”
Im questioning the PTF tape and and the aoe correction and the not new shining also the way he said just remove teeth from the position untill it gos in smoth is not a good idea I learned more about tech work bye watching negative Airsoft
@@Revan638 same same. Built a couple of guns now and the last one was my brothers tm p90. It is still a AEG and had guys at the field asking if it is HPA. it almost the same sound as a HPA just a little muffled pop using a mock suppressor.
@@MikeHuntsPewsnice did you use a tool of some kind to shim the gear box I know to get into a v2 gear box but shimming is hard for me I would try to do the bevel to pinon method but I just not good yet
@@knightairsoftwarrior if your not good at working on them I would suggest not to unless you have enough money laying around to buy a new gun if you happen brake something. No tools needed to shim other then gearbox screws driver. To do any sort of nice job on anything you need all of the tools, yes all of them.
Well do you have the etu g&g mosfet? that is capable of doing 3 round burst but usealy that in the full auto position! Not semi maybe che k and see if your cut off lever is catching fast enough if not thats exactly why it's doing that' hope that kinda helps
May be a bit late, but there is a cutoff lever that engages after one cycle when firing in semi auto mode, causing the motor to stop spinning. therefor you can use any combination of Gears and Motors and it will always stop at the right time/point
Oi coloquei engrenagem 12:1 na minha ares 013, e agora mesmo no semi ou ful ela da uns 6 tiros e para mais uns seis tiro e para de vez pra voltar do tirando a bateria e colocando denovo, sera que o ímã ficou fraco? Usei o ímã original oque vc acha?
Lemme tell you a secret, there are 4 types of SHS in China Mainland / HongKong Type 0 - HongKong Exported Type 1 - As good as Type 0 - look exactly the same as Type 0 - but will not be exported since QC is less strict. Type 2 - Lower Quality but has a decent Bevel Teeth Type 3 - The shittiest Gearset - The one you use in your video - But still you have a decent Bevel... --- Sorry but I had to tell you the truth.
-opens gearbox on the wrong side.
-uses tacky grease.
-lowers the air volume with a faucet washer.
-dosent check air nozzle compression
-glues it on the cilinder head, it actually goes behind the piston head.
-greases the anti-reversal latch.
-dosent shim the gears.
-dosent lube the piston nor the piston rails.
-overtorques the crap out of the screws
😂
You trust G&G's shimming job? Those are completely new and different gears than the G&G gears you removed. Bruhh
This
I was thinking the same thing!! No reshimming after a new gear set?!? Wild!
😂
Maybe this is just a video example of teching a v2 aeg gearbox 😅
It’ll be Alr they ain’t got to be perfect
Very helpfull video i will propably buy a new motor and a set of gears for my gun soon and will rewatch this if i need any help. Great content!
tbh this is an easy way to destroy your gearbox. He throws in new gears, every gear is has different tolorances even when they're the same brand. Go watch TheAirsoftTech on how to shim.
This is so helpful
Agreed
This guy is terrible there are way better videos out there
@@notlars_7891not everything he did is wrong he opens the gearbox from the wrong side lol
chill with that screw😭
I think you opened the gearbox upside down, it seemed to work but that's at high risk of the tappet or and spring ready part to fling out and either mess up an already shimmed gearbox or just shoot things all over the place
can you use bicycle grease from a hardware store or does it have to be high speed gearbox grease?
No I hope you didn’t this whole video is wrong
@@something4479 what is wrong with it?
@@zura5427 everything he doesn’t know what he’s doing or talking about all his facts are out of line
Yes you can, not on the o-rings but you totally can use bike grease on the gears.
@@A-G-F-0:42
Please for the love of god and all things good in this world like airsoft, DO NOT DO ANYTHING YOU SEE IN THIS VIDEO TO YOUR GUN. Some of the worst advice and worst work I have ever seen. Literally everything he did was wrong and miss information.
The title of this video should be ”how to brake your pew in 13:1 steps”
Im questioning the PTF tape and and the aoe correction and the not new shining also the way he said just remove teeth from the position untill it gos in smoth is not a good idea
I learned more about tech work bye watching negative Airsoft
@@Revan638 same same. Built a couple of guns now and the last one was my brothers tm p90. It is still a AEG and had guys at the field asking if it is HPA. it almost the same sound as a HPA just a little muffled pop using a mock suppressor.
@@MikeHuntsPewsnice did you use a tool of some kind to shim the gear box I know to get into a v2 gear box but shimming is hard for me I would try to do the bevel to pinon method but I just not good yet
@@knightairsoftwarrior if your not good at working on them I would suggest not to unless you have enough money laying around to buy a new gun if you happen brake something. No tools needed to shim other then gearbox screws driver. To do any sort of nice job on anything you need all of the tools, yes all of them.
@@Revan638 removing the 15th teeth is very common and most pistons shouldn't even come with the 15th tooth
Is it okay when there is too much grease?
Was this video made on April 1st ? Because it’s a joke 🤣🤣
Hey what happens if after I install 16:1 gears, on semi, my gun shoots a three round burst instead of a single shot?
That should work fine
Well do you have the etu g&g mosfet? that is capable of doing 3 round burst but usealy that in the full auto position! Not semi maybe che k and see if your cut off lever is catching fast enough if not thats exactly why it's doing that' hope that kinda helps
You need a mosfet with active braking. Your getting overspin.
May be a bit late, but there is a cutoff lever that engages after one cycle when firing in semi auto mode, causing the motor to stop spinning. therefor you can use any combination of Gears and Motors and it will always stop at the right time/point
Oi coloquei engrenagem 12:1 na minha ares 013, e agora mesmo no semi ou ful ela da uns 6 tiros e para mais uns seis tiro e para de vez pra voltar do tirando a bateria e colocando denovo, sera que o ímã ficou fraco? Usei o ímã original oque vc acha?
Ares has his own gears... that work with his own e-trigger so.... u are just making it go crazy cause it doesnt know if its working or not hahahah
Lemme tell you a secret, there are 4 types of SHS in China Mainland / HongKong
Type 0 - HongKong Exported
Type 1 - As good as Type 0 - look exactly the same as Type 0 - but will not be exported since QC is less strict.
Type 2 - Lower Quality but has a decent Bevel Teeth
Type 3 - The shittiest Gearset - The one you use in your video - But still you have a decent Bevel...
---
Sorry but I had to tell you the truth.
I know this comment is old. But how can you tell the difference? And what type are Rocket gears?
That’s not even a dsg build it’s a ssg build
Dropped the gear trying to show us angle of attack and scared me lol
no reshimming. that's a BIIIIIG no no.
Bruh that ain't the right grease and you most definitely want to re shim!! 😂😂😂
The grease could work, it looks to be too tacky but it really dosent do anything catastrophic, i would have used something thinner but anywats
I suggest doing it a little faster, it is very lengthy of a video, I think it would benefit your channel. You did good
He did a shitty job lol
lol wtf
SEM ALTERA
Install new gear set without reshimming the gears? Dude, stop, go get some help !