Thanks for the videos. You helped me get get far in my diagnosis of a gm e37 no com. It has .5v on both can channels and 1.1v on 5v reference. Watching your videos and using a known good ecu I was able to apply 5v to the back of , what I think is a mosfet. And the ecu now can communicate!! Wow great experience. Now to find out where the problems actually is lol
Great job thanks for sharing. You are correct, we all learn by doing. I am playing with some projects that I fint have the answers for and this pushes me to learn.
Is it possible for a ECU from a company that programs them could have not left the ecu in the proper mode. I have powers and ground. 5 volt ref all seem fine on the sensor ports. The wires from the ecu for the relay have power when hooked to the ecu. I was able to engage the relay with 2 testlighs when the ecu was unhooked. But it seems like my ECU is the issue. I have no comm with my scanner to the system. U1000’s on all modules. I’m at a lost. Feel like I should send the ecu back to the company for Testing!
Another great video, thanks. I usually come across pcms that are bad on Hondas mainly due to water/moisture damage, and just 2 days ago I have to replace one on a 2009 Accord. Most of the time the symptoms are no communication and immobilizer key light flashing. But the recent Accord didn't even light the immobilizer key light. I wanted to learn how to repair these pcms and right now I have 2 sitting around and playing with them to learn more about how they work. I wanted to suggest if you find it acceptable to ship one to you for a video on repairing. Btw I am from Nigeria, thanks
1/2 voltage might indicate a single diode failure if there is a two diode control circuit to provide the 5vdc ref? Of course you'd need a true schematic of the circuit layout to know for sure.
My 2015 Nissan frontier's door locks randomly go crazy any thoughts ? I put in a plug and remote start kit and it started starting an shutting of randomly and I had to remove it ?
Can you diagnose a 1995 jaguar XJR, the supercharged 4.0 inline 6 ? Car super tricky to get running and will run beautiful, start a few times and then not start again . Told by local shop that ECM is a ceramic board ? and it’s cracked and bad and cannot be fixed . Car is quite rare but no good not working . Located in Ontario Canada
Hi saw your video ...sir I have also. ECU WLAE18881c. .the problem no 5volts of 3pins in crankshaft sensor ...what the ECU work what's parts of ECU check .. thanks from Philippines.
@@DKr475You can test them like any other component but to do it right and simulate running engine then you just add a immobilizer setup to your test bench.
Hey friend. After watching your videos. I find that you are very suitable to review our led headlight bulb, are you imterested? But I don't know how to contact you. Hope to hear from you, thanks.
@@MaicSalazarDiagnostics Thank you. I have sent the collaboration email to you, the subject is Boslla Headlight Bulb Collaboration, look forward to your reply.
Thanks for the videos. You helped me get get far in my diagnosis of a gm e37 no com. It has .5v on both can channels and 1.1v on 5v reference. Watching your videos and using a known good ecu I was able to apply 5v to the back of , what I think is a mosfet. And the ecu now can communicate!! Wow great experience. Now to find out where the problems actually is lol
Amazing setup & knowledge you have!!!
I appreciate that! Thank you so much my dear friend.
Thanks for taking care of it for me buddy. I appreciate it.
Nice video. Ive been keeping modules to try to fix one. This is great info. Thank you for being a quality content provider.
Great job thanks for sharing. You are correct, we all learn by doing. I am playing with some projects that I fint have the answers for and this pushes me to learn.
Gracias Maic, sigo aprendiendo mucho y poniéndole bastante, buscando información cada día pura vida!
Bendiciones
@@MaicSalazarDiagnostics igualmente, saludos!
Good job on the video Maic, you mentioned @3:54 providing a link in the description for Automotive Universal Test Platform?
Maic thank you for sharing! Excellent video!
Is it possible for a ECU from a company that programs them could have not left the ecu in the proper mode. I have powers and ground. 5 volt ref all seem fine on the sensor ports. The wires from the ecu for the relay have power when hooked to the ecu. I was able to engage the relay with 2 testlighs when the ecu was unhooked. But it seems like my ECU is the issue. I have no comm with my scanner to the system. U1000’s on all modules. I’m at a lost. Feel like I should send the ecu back to the company for Testing!
Yes it is possible. And you should definitely contact them.
Thanks for the tips. Appreciate the guidance
How do you determine what power and grounds are needed. Do you have a video on how to determine what wires are needed from breakout box?
Nice breakout box and test kit! What test leads do you recommend for ECM pin connections?
Another great video, thanks. I usually come across pcms that are bad on Hondas mainly due to water/moisture damage, and just 2 days ago I have to replace one on a 2009 Accord. Most of the time the symptoms are no communication and immobilizer key light flashing. But the recent Accord didn't even light the immobilizer key light.
I wanted to learn how to repair these pcms and right now I have 2 sitting around and playing with them to learn more about how they work.
I wanted to suggest if you find it acceptable to ship one to you for a video on repairing. Btw I am from Nigeria, thanks
1/2 voltage might indicate a single diode failure if there is a two diode control circuit to provide the 5vdc ref? Of course you'd need a true schematic of the circuit layout to know for sure.
the intelligent fuse box might end up on your bench next. 🤣
thank you very much maic!
nice set up
Great setup, Good work
My 2015 Nissan frontier's door locks randomly go crazy any thoughts ? I put in a plug and remote start kit and it started starting an shutting of randomly and I had to remove it ?
Can you diagnose a 1995 jaguar XJR, the supercharged 4.0 inline 6 ? Car super tricky to get running and will run beautiful, start a few times and then not start again . Told by local shop that ECM is a ceramic board ? and it’s cracked and bad and cannot be fixed .
Car is quite rare but no good not working . Located in Ontario Canada
Sorry no help on that.
Amazing video 🙂🙂🙂👌
Thank you Mr. Salazar .
Hi saw your video ...sir I have also. ECU WLAE18881c. .the problem no 5volts of 3pins in crankshaft sensor ...what the ECU work what's parts of ECU check .. thanks from Philippines.
Can u say where do you get datasheet for that type of ic ? For example bosch type.
Please can you send me the reference voltage for 1mz PCM? The scanner isn't communicating with the Avalon.
It would be cool to see the part replaced. Thanks.
Is a ecu repair business possible in 2021
Great video but still am wondering how the ECM works with the simulator without immobilizer?
The ECM is on not running. You can comunícate even with out the inmo.
@@MaicSalazarDiagnostics but how i can test output of injectors or coils with immobiliser on?
@@DKr475You can test them like any other component but to do it right and simulate running engine then you just add a immobilizer setup to your test bench.
@@ecurepair yeah. Thats the Point.
Hii Maic....plzzz let me know from what website i can get the wiring diagrams of ECU???? plzzz advice...thank you
This is very helpful
Making real sence what to do
Interestingly, the microcircuit was warming up? Could the malfunction have been detected by the thermal viewer?
Usually yea
Amazing Video
if i send you my ecu and you repair it can i just plug it back in and my xterra start? without having to do anything else?
That is correct
What is the problem with the ECM? I need you to send me the diagnostic report from your mechanic. Please email me at info@maicsalazardiagnostics.com
@@MaicSalazarDiagnostics any chance I can have your email for info about a ecu for 08 nissan pathfinder
@@Steve-pf8tb sure it is maic@maicsalazardiagnostics.com
do you repair ecu's whats the price?
email me at maic@maicsalazardiagnostics.com please let me know year and model and what module you need to repair.
Where do you get the power board
Power board is from WEIXY Electronics
Well done buddy
You have Subscribers from pakistan too...
Welcome to the channel!!
Like to learn that it's my dream
Can you verginize modules?
Depends the manufacture
@@MaicSalazarDiagnostics m.B
@@MaicSalazarDiagnostics I think its a 2002 c500
@@MaicSalazarDiagnostics cl
Hey friend. After watching your videos. I find that you are very suitable to review our led headlight bulb, are you imterested? But I don't know how to contact you. Hope to hear from you, thanks.
info@maicsalazardiagnostics.com
@@MaicSalazarDiagnostics Thank you. I have sent the collaboration email to you, the subject is Boslla Headlight Bulb Collaboration, look forward to your reply.
wer is your location boss?
I am located in Herndon VA. Any other information you need please email me at maic@maicsalazardiagnostics.com
Thanks
Man you ard the one
Ur a college brother without no fees
Impression setup man
Ford Everest my car
Impressive setup!