Y'all should drill a hole and put some type of air fitting on that fuel can so y'all can pressure it up a little to help with pressure to prime the fuel system not much maybe 2 to 3 psi to help push all the air out the system and prime it faster than gravity........... it might be a new thing the ppl that own the can patent didnt think of but ive never seen one with a air fitting yet
We worked on my 7 year old grandson’s go-cart last weekend. Watching this video, he said “maybe they should check the points.” I smiled and gave a little laugh. Shows he’s been paying attention.👍🏻 We watched a couple of videos on how a Diesel works. That kid just loves to learn!
Nearly all those old diesel engines have glow plugs. They will be hard to start or even impossible to start without working glow plugs !!! Most of the time you turn the key or start switch to the left and hold it to heat the glow plugs. Make sure they are working at least two or three of them. Next bleed the fuel lines at the injectors !!!!! Bleeding lines at the pump helps but it can take a long time to get the fuel up to the injectors from the pump. Bleed the lines at the injectors to save hours of cranking time !!!!!
I grew up fishing on that property... I am sure My Father helped build those ponds back in the late 60's... I NEVER knew it was Down there!... The Father in Law was one of My Father's Best friends... they worked together until the Man Passed... I am sure My father drove that to help them build those lower two ponds... the upper pond was built when State built the Circle.
Need five more gallons of starting fluid a d a bigger claw hammer. Not getting fuel to injectors. Need to have a small pressurized tank to hook up to line at filter and case fuel to injector lines.
My old Dad’s first crawler was a HD-6 , been many years since I’ve seen one . We cleared fourty aces of land with it , logged it and stumped and burned it . Made pasture land for our cattle . Every morning in the winter I plowed 3/4 of mile of driveway , up hill to the hyway . Using a low powered machine made you work strategically , turned me into a good cat operator . Later we got some larger cats , my experience with the smaller machine gave me the ability to run them well . 👍🇨🇦
Hank and Willie don't care how long its been sitting or how ugly a machine is their willing to do their best to get it going it's incredible what they get running keep up the great vidio's.
I remember the first time I ran a dozer and when your off loading one, square up with the ramps and stay off the steering brakes unless you use them both at the same time and let her roll. And a single chain is never as strong as a doubled up one and then old boys should have known that a LONG time ago
I retired from a Cat dealership in FL. I used ether for years. When I started for Cat, they didn't sell it or use it. They did allow gasoline. You put a rag over the intake. Squirt a tiny bit of gas. It will " pop" & jar those stuck rings loose You have everything there but compression it looks like . Gas is not as destructive., but just like ether you got to be careful.
Y’all might consider a form oil sprayer has-brass fitting to adapt and provide bypass with pressure to bleed injection pump and eliminate fuel supply problems
Hey Hank and Wiley was watching a episode the other day and you told a joke Hank about who do you not say hi to in a airport someone named Jack that is hilarious when someone says hi to me I say don’t say that in a airport love you guys love to see you guys show your faith
Glad to see you guys even though you not sent me any notes but anyway the old gasoline trick I mentioned to you worked! I knew it would! Glad to see it running on its own! You guys are always awesome and keep em coming!!!
Hi John, I`m a Brit and love my Landrover turbo diesels here, they are more common than Gas engine ones, but some years ago when fuel got expensive my old diesel ran very well on half diesel, half new bulk buy cooking oil (ECO DIESEL NOW) and a good splash of unleaded gas (petrol) it ran better than straight diesel, sounded quieter but smelled of French fries behind me -LOL.. So your give it some gas in my case was good.
It’s getting fuel now just don’t got enough compression you can hear it losing it just by the way it’s cranking and when you see smoke and dump a can starting fuel in it there’s not enough compression to fire it.
Thanks for the video. When you have one sitting for a long time, the rings stick and lose compression, the marvel mystery oil let sit in the cyclinder for a while usually will help loose things up
Did Hank mean Full Metal Jacket when he said all metal ?! Some of these would take a high-pressure sprayer to clear out the mud and leaves while they are soaking in oil. Has to help - or a powerful battery blower.
Hank and Whilley that was great enjoyed it thank you for sharing and your time was really great never saw gas in the mystery oil but it worked fantastic.
Excellent video Wiley :) , Hank :) also yes Vinegar plus alcohol in Desiel fuel help kick over motor to trying to sometimes ! Yes guys work hard this one and also thought say this never going out start threw in towel on this one!
I think it’d be pretty cool if you and Wiley could find either an older or newer D9-D-11 Cat to get cranked up! Either way I Love the content Hank!!! 👍🏼
Hank sure is having a lot of fun pushing that starter switch...maybe he got told no a lot when he was a kid whenever he asked Ooh ooh can i push the button?
Out of all the will it start this has two be the best .. I figured it was a lost cause.. That was great call with the gas it was like the hail Mary pass at the end of the game. Hank you and Wiley out did yourself..
I went into Walmart to buy some ammo. The counter girl put it on the counter and I pulled out my card when she said "Strip down, facing me". I thought "This privacy invasion is gettin' out of hand. I'm gonna write my congressman and the NRA about this crap". But I needed the rounds so I did like she said and dropped my pants and drawers and she screamed and ran off somewhere. In a few minutes the manager came up to me and explained that she was telling me how to use my card in the reader. He also told me "Please don't shop here any more". 😎
I would like to thank Hank and Wylie these guys are great love watching the show love seeing what you do you're my American mates thank you from Down Under
gasrag it wet a thick towel in gasolene stuff in breather pipe when engine fires up jerk rag out really quick it will help the engine fire after setting a long long time
I always wonder with these rescue videos if one or more cylinders has filled with water from rain or condensation getting in exhaust or intakes and getting past open valves!
fuel pump, etc doesnt mean anything if your not firing off all that starting fluid wally put in it. you guys have a compression issue. maybe rings or could be a compression release that is stuck open. Def. compression, you can hear it in the way it cranks. there is hardly a gallop to it like a normal engine would have when they come up on compression stroke.
That is a existent machan its about a D5 . I oust to own one a log with and land septet with the winch is very powerful, never gat suck .Well done boys.
Thanks for another great video. It was interesting. Wow and wow. You two gentlemen got it to run-yea!!!!!!! Nice job Wiley and Hank. Now get it loaded and out of there. Thanks guys. The Iowa Farm Boy.
Poor old girl has got a serious lack of compression on one cylinder I think. Its had a hard life and needs spannering to take her head of and look what's she's got missing. 10 out of 10 for getting it running though guys.
Has burned valve on one cylinder for sure probably needs valve seats and valves. Plus new rings maybe a cracked head By how much exhaust was coming out of the rad
![Felix "Unfair" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/Oswujxm2Ag0/mqdefault.jpg)
▶️Watch CASE BACKHOE HERE: ruclips.net/video/CtE2ndH6O40/видео.html
Hank do you have any advice on grief I have autism and lost my mom to cancer when I was driving her to doctors appointments and taking care of her
I thank you all need to take off those fuel fiftres oof they may have gaunt in it
Y'all should drill a hole and put some type of air fitting on that fuel can so y'all can pressure it up a little to help with pressure to prime the fuel system not much maybe 2 to 3 psi to help push all the air out the system and prime it faster than gravity........... it might be a new thing the ppl that own the can patent didnt think of but ive never seen one with a air fitting yet
If you guys don't know there's audio running over audio in this video
5:21pm.en Morelia Michoacán México pico del tzirate 159 colonia Santiaguito
We worked on my 7 year old grandson’s go-cart last weekend. Watching this video, he said “maybe they should check the points.” I smiled and gave a little laugh. Shows he’s been paying attention.👍🏻 We watched a couple of videos on how a Diesel works. That kid just loves to learn!
Those are the most important "points". 😀 God Bless You and Your Grandson!
Love you guys you two are truly amazing characters and when I start watching one of your videos I can’t stop watching lol ❤❤❤
Nearly all those old diesel engines have glow plugs. They will be hard to start or even impossible to start without working glow plugs !!! Most of the time you turn the key or start switch to the left and hold it to heat the glow plugs. Make sure they are working at least two or three of them. Next bleed the fuel lines at the injectors !!!!! Bleeding lines at the pump helps but it can take a long time to get the fuel up to the injectors from the pump. Bleed the lines at the injectors to save hours of cranking time !!!!!
I grew up fishing on that property... I am sure My Father helped build those ponds back in the late 60's... I NEVER knew it was Down there!... The Father in Law was one of My Father's Best friends... they worked together until the Man Passed... I am sure My father drove that to help them build those lower two ponds... the upper pond was built when State built the Circle.
Need five more gallons of starting fluid a d a bigger claw hammer. Not getting fuel to injectors. Need to have a small pressurized tank to hook up to line at filter and case fuel to injector lines.
Those electric fuel pumps require being primed or a slight gravity feed. They are not a suction pump
Hank and willie both looking well
If a diesel wont hit on starting fluid, it lacks compression. As long as that machine has been setting, rings and valves are likely stuck.
That’s what that red bottle is for little extra fluid pressure lol
They shouldn't have use either to begin with. Cylinder walls and piston rings are so dry lacking oil from sitting so long.
@@OldFarmAcresJoelK. This is why I use silicone spray
WD40 only.
The starter is spinning the motor to easy. No compression. Rings stuck. Need to free them up and use some heavy oil to get some compression.
My old Dad’s first crawler was a HD-6 , been many years since I’ve seen one . We cleared fourty aces of land with it , logged it and stumped and burned it . Made pasture land for our cattle . Every morning in the winter I plowed 3/4 of mile of driveway , up hill to the hyway . Using a low powered machine made you work strategically , turned me into a good cat operator . Later we got some larger cats , my experience with the smaller machine gave me the ability to run them well . 👍🇨🇦
Hank and Willie don't care how long its been sitting or how ugly a machine is their willing to do their best to get it going it's incredible what they get running keep up the great vidio's.
Thank you
I remember the first time I ran a dozer and when your off loading one, square up with the ramps and stay off the steering brakes unless you use them both at the same time and let her roll. And a single chain is never as strong as a doubled up one and then old boys should have known that a LONG time ago
I retired from a Cat dealership in FL. I used ether for years. When I started for Cat, they didn't sell it or use it. They did allow gasoline. You put a rag over the intake. Squirt a tiny bit of gas. It will " pop" & jar those stuck rings loose
You have everything there but compression it looks like . Gas is not as destructive., but just like ether you got to be careful.
Its got a really strong starter..its got plenty of life in it
That allis chalmer is a 1926 187 model AAA only 1,568 of them were made during that year
Y’all might consider a form oil sprayer has-brass fitting to adapt and provide bypass with pressure to bleed injection pump and eliminate fuel supply problems
Hey Hank and Wiley was watching a episode the other day and you told a joke Hank about who do you not say hi to in a airport someone named Jack that is hilarious when someone says hi to me I say don’t say that in a airport love you guys love to see you guys show your faith
lol
I absolutely love coming along with yous all on these crazy adventures don’t give up i am certain it will run
We're glad you spent some time with us tonight!
Those black lever handles were the must have for the gearstick in ya truck back in the day
Glad to see you guys even though you not sent me any notes but anyway the old gasoline trick I mentioned to you worked! I knew it would! Glad to see it running on its own! You guys are always awesome and keep em coming!!!
Hi John, I`m a Brit and love my Landrover turbo diesels here, they are more common than Gas engine ones, but some years ago when fuel got expensive my old diesel ran very well on half diesel, half new bulk buy cooking oil (ECO DIESEL NOW) and a good splash of unleaded gas (petrol) it ran better than straight diesel, sounded quieter but smelled of French fries behind me -LOL.. So your give it some gas in my case was good.
Looks similar to an Allis Chalmers that I have sitting out at my ranch since 1985. It is from the 50's. The one I have has a 3 cylinder Detroit.
Boy oh boy!! I’ll tell you what, fellas that was brutal to watch. Wow!! That was one of y’all’s best episodes yet. 😎👍🏻🙏
Hank see that round ball lever it’s the shutdown lever work it hard back and forth in is to run.
Probably the marvel oil freed up the rings and helped with creating a little better compression.
Always amazed at this old heavy duty equipment that gets abandoned in the woods, lots of these videos out there!
GOOD JOB GUYS, YOU GUYS CAN START JUST ABOUT ANYTHIN' FUN VIDEO, THANX... PEACE FROM CREEL CHIHUAHUA, MEXICO
It’s getting fuel now just don’t got enough compression you can hear it losing it just by the way it’s cranking and when you see smoke and dump a can starting fuel in it there’s not enough compression to fire it.
Thanks for the video. When you have one sitting for a long time, the rings stick and lose compression, the marvel mystery oil let sit in the cyclinder for a while usually will help loose things up
Unbelievable! I love folks who can fix stuffs.
Did Hank mean Full Metal Jacket when he said all metal ?! Some of these would take a high-pressure sprayer to clear out the mud and leaves while they are soaking in oil. Has to help - or a powerful battery blower.
Hank and Whilley that was great enjoyed it thank you for sharing and your time was really great never saw gas in the mystery oil but it worked fantastic.
Thank you sir
Sounds good at least it runs. I think it might of been flooded had way to much fuel in the cylinders
Excellent video Wiley :) , Hank :) also yes Vinegar plus alcohol in Desiel fuel help kick over motor to trying to sometimes ! Yes guys work hard this one and also thought say this never going out start threw in towel on this one!
I think it’d be pretty cool if you and Wiley could find either an older or newer D9-D-11 Cat to get cranked up! Either way I Love the content Hank!!! 👍🏼
Hank sure is having a lot of fun pushing that starter switch...maybe he got told no a lot when he was a kid whenever he asked Ooh ooh can i push the button?
lol. I'm sure that happened a lot 😂
Out of all the will it start this has two be the best .. I figured it was a lost cause.. That was great call with the gas it was like the hail Mary pass at the end of the game. Hank you and Wiley out did yourself..
Thanks. It was fun
@@HamiltonvilleFarm I feel like it had water in the diesel fuel or the filters
It was a long time coming but puff puff puff and finally the it runs now the better it will get well done gentleman 👍👋🇨🇦
I went into Walmart to buy some ammo. The counter girl put it on the counter and I pulled out my card when she said "Strip down, facing me". I thought "This privacy invasion is gettin' out of hand. I'm gonna write my congressman and the NRA about this crap". But I needed the rounds so I did like she said and dropped my pants and drawers and she screamed and ran off somewhere. In a few minutes the manager came up to me and explained that she was telling me how to use my card in the reader. He also told me "Please don't shop here any more". 😎
That was a good one lol
Good one 😅😅😅😅
Great video. Thanks for sharing. Glad you guys still do WILL IT START
I would like to thank Hank and Wylie these guys are great love watching the show love seeing what you do you're my American mates thank you from Down Under
You have stuck exhaust valves. You need to check either, believe you got some dead stuff
That hissing when he’s crankin it tells us there’s valve issues
It’s an AC I had no doubt it would start! Great job guys!👍
propane torch heat the block/manifold up since de glow plugs not be working theirs is a light that glows red
My great grandfather worked for Allis Chalmers he had a WD45 and a deutz allis as his personal tractors
Cool👍
When I see a new video uploaded, I get excited 😅!!!! You fellas do a great job keep ‘em
Comin Wiley and Hank!!!!
Its like watching abbot and Costello..! Lol..
We appreciate that! Thank you
I think it might run 🏃 the both of you should have a good day
if it isn't locked up, I believe you two fellas can get anything diesel running again. Great job as always. Kerry
Once it starts spinning good release the compression release.
Hank, how many times did you walk past the moccasin laid up by that pine tree. Wily missed it too!
😳
Wow that was the best will it start . Do a part 3 to see if you can get it to move
I absolutely love seeing what y'all get yourselves into!! Great job y'all, don't give up, God Bless y'all and stay safe!! Y'all act like brothers 🤣🤣🤣
gasrag it wet a thick towel in gasolene stuff in breather pipe when engine fires up jerk rag out really quick it will help the engine fire after setting a long long time
With a diesel of this age doesn't it have glow-warm coils?
Wow! That was amazing! Great job, guys. Great job, both of you!
Good job guys you all got it going that's what counts
I always wonder with these rescue videos if one or more cylinders has filled with water from rain or condensation getting in exhaust or intakes and getting past open valves!
You’re an awesome team!, thanks for posting your videos! God blessed you!
Thank you! You too!
Watching you in Hiddenhausen Germany 😊
I got to ask what is up with Wiley’s hat?? YES. lol
It's the Col.Hank and Wiley show!...was waiting for an update on these rigs sittin' out there..
Right on! This is a good episode
Thank you 4 the appreciation Hank
The oil on the dipstick is a VERY good sign. It is an Allis Chalmers, after all.
fuel pump, etc doesnt mean anything if your not firing off all that starting fluid wally put in it. you guys have a compression issue. maybe rings or could be a compression release that is stuck open. Def. compression, you can hear it in the way it cranks. there is hardly a gallop to it like a normal engine would have when they come up on compression stroke.
Get some REAL ether- John Deere . It’s 80%! Doesn’t take much either!
That is sooo cool, sure am glad to here it run
That is a existent machan its about a D5 . I oust to own one a log with and land septet with the winch is very powerful, never gat suck .Well done boys.
Another great video guys thank you both and god bless
Thank you
Thanks for another great video. It was interesting.
Wow and wow. You two gentlemen got it to run-yea!!!!!!!
Nice job Wiley and Hank.
Now get it loaded and out of there.
Thanks guys.
The Iowa Farm Boy.
I threw my fists in the air when that engine started running! 😂
Great job guys, that was a hard one to crank. I like those old ones though, like the allis, or an Oliver or a white. Call that one old smoky.
Love the longer videos ❤
Thanks!
Thank you kindly
Just shows that persistence and perseverance pays off (P&P) 😅😅.........oh, and Hank's idea of using the gas! Great job guys!! 👍😎
Yes! Thank you! 😁
Sounds like it has no compression maybe it has a decomposition leaver
Impressive guys good job
$2.96 for fuel!!!! .. $3.29 here in Maryland.. great video fellas.. awesome machine to get to see pop off
It's 1.70 a quart in BC Canada!!
@@davecody5997 it's the same🤣🤣🤣🤣
On mine if you starting fuild don't sray while turning engine over, I don't think it smoke looks like fuel.
Happy Thanksgiving to you and the family
How do you guys know there's no rust down in the tank?
apparently it seems that there is no diesel reaching the filters and so on
I love these videos of guys bringing rusty piles of crap back to life.
Poor old girl has got a serious lack of compression on one cylinder I think. Its had a hard life and needs spannering to take her head of and look what's she's got missing. 10 out of 10 for getting it running though guys.
You guys are OK in my book!
Would love to hang out with you for a day.
one hour and twenry-four minutes. Love your videos but thank the Lord for fast forward LOL. Love you and Wiley.
gasoline on a cloth work better than spray can and abit of brake fuid will free the rings
I think you fellas smoked out all the mosquitoes. Good job.
I would call it "burning love"
Like to see you in Canada 😊 to fire up some equipment we got lotz
Love your videos you came along way
Thank you
Has burned valve on one cylinder for sure probably needs valve seats and valves. Plus new rings maybe a cracked head By how much exhaust was coming out of the rad
I was gonna say sounds like there’s a cylinder or two with a couple bad valves
06:28 - how many dipsticks can you see...
keep it up boys
Sounds like to me the Rings are stuck on the piston and it doesn't get no compression
You said”they don’t make them like this anymore”. Thank goodness!😂
lol. True
Had my doubts. Y'all got it. Cool
That old mochine has a heck of a starter.
well, that old Allis has a good starter, but why wont it hit on ether?
Love that never give up attitude awesome guys sweet
Literally fist pumped the air in the middle of dinner when it finally started running!
Right on!!
Its the amazing song stylings of you two for me!!!!
That was a nice sounding dozer
Y'all are the best fellas!!!;;
Wow! Excellent job.
I couldn't get the cap off Marvel's mystery oil bottle. One time I use a pair of vice grips. I broke the top of the bottle