Finished mine and made some 5/16th, 3/8, and 1/2 inch dowels from oak stock and all of them turned out great! No need for buying high priced hardwood dowels anymore!! Could not be happier with it. Did add a guard onto the back end to prevent any "biting"
I searched on youtube videos about making various dowels and found easier methods day by day, but i think yours is the climax of my search. Thank you for sharing my friend..regards from Indonesia.
Made a bunch of quarter inch dowels today with the jig. They are more finicky then the 3/8" dowels. I found the smaller stock size would splinter if I tried to pull the part that was in the drill chuck like I did with the 3/8" dowels. The quarter inch dowels wouldn't take the stress as well. I just cut off the square part. Worked very well once I got it dialed in. I did make a extra set of blocks as my first set had shifted and went back to just a 3/8" starter hole to the quarter inch out hole. The tolerance with the quarter inch dowels is much more picky. I went from having a few store bought dowels to having over a hundred just using my scrap oak, maple, cedar, walnut. The oak gave me the most trouble in the smaller size of dowel. GREAT JIG!
Это тот самый момент, когда на приспособление тратится больше времени, чем на саму работу - и это правильно! Ещё бы стружкоудаление сверху провести - будет вообще круто! С меня лайк за идею, воплощение и работоспособность! =)
Ваня, при помощи простой лерки нужного тебе диаметра, вставленной в плашку, и зажатую в тиски ты сделаешь тоже самое. И никакой головной боли с изготовлением всяких не нужных " приспособ". Старинный дедовский метод , кстати.
Need to make a fair number of long dowels 16 and 20mm and out of all the dowel making videos this one seems to be the one I need. Thanks for sharing. Andy UK
I can't improve upon the comments that are already here, just like I can't improve anything about your dowel device. The fit and finish are second to none. There are a lot of great ideas here on RUclips, but few demonstrate the skills you've shown. Very nice. This could be a real money maker for anyone willing to make dowels. Quality dowels "Not Be Cheap!" They are hard to find and seldom come in a variety of woods. Plus, chucking a drill onto the finished end would allow you to finish each dowel by pulling the final few inches through... Worth it instead of just cutting off the square end? IDK... Just a thought. Just a little less waste.
I'm. Attempting. TODAY!. The other jigs where you pound the dowel through metal or even chuck it up to drill are just a royal pain. Too much effort for one stinking 4" dowel. THANK YOU! Hope I can make mine as precise as yours.
Thought this was a great design and built it, inititially dowels were coming out undersized. Realized that when I marked the high point of my blade, it was in the full up position. Later when using the jig to make dowels, the blade was lower. My saw pivots when raising the blade so the high point was actually further back. Once I adjusted the mark on fence to correspond to the new peak worked like a champ. Apprec I ate you sharing the design.
Eine sehr gute und simple Konstruktion. Die Genialität liegt hier wohl in der Einfachheit. Eine besondere Hilfe in der Werkstatt. Regt mich zum Nachbau an. BG from Austria
Как мне нравится смотреть на все такие столярные работы.))) Я и делатть люблю и креативить. Единственное что не люблю, так это видео монтажём потом заниматься. ))))))
Very easy to make! Perfect result! I've watched a lot of videos and this is the best dowel making device I've ever seen. So far I have used a metal plate with matching holes. Now I`ll make this dowel maker. THANK YOU VERY MUCH for such a detailed video.
Thank you very much for showing this! I had already created a very 'no nonsense' dowel jig what was working (without the tablesaw), but i kept thinking about one with the tablesaw, came across your video and decided to make it tonight. I did change some things (because that made it easier for me: - i did not do your thing with the bolds and wing nut-thingy, i just uses a screw that i can turn in and out (filed the tip of a little) That saved me a lot of time and i believe it works as well. Ah, and i had to make the jig to understand why you created the part at 3:07, i thought you used it to make it easier to insert the long stick, but it had a different (better) reason ;-) I made it tonight, and tried it on one (i only created 1 size for now) and although the top of the stick came out smaller (i think because it was not really centered when entering), the big middle part was perfect. Thanks again!
Thank you, Once more you have showed me something that I will be pleased to make thanks to you, carry on with your good videos and I will be pleased to make all the great things you are showing me. Thank you great work, Best of luck 🤞 🍀👍
Thanks. Made one yesterday and made 30 dollars worth of walnut and oak dowels. Best jig award. Thanks for sharing.
Finished mine and made some 5/16th, 3/8, and 1/2 inch dowels from oak stock and all of them turned out great! No need for buying high priced hardwood dowels anymore!! Could not be happier with it. Did add a guard onto the back end to prevent any "biting"
I searched on youtube videos about making various dowels and found easier methods day by day, but i think yours is the climax of my search. Thank you for sharing my friend..regards from Indonesia.
12345678901
This is the best dowel maker I've seen yet.
Mee too
I finally gave this a try only because this design is compact enough to be worth the space.
Absolutely a fantastic idea. Thank you.
From Missouri USA
Making dowels, as much fun as you can have with your cloths on
Most efficient plans yet😮
Mate you are a genius
Thanks for pointing out that you made the dowel hole to close to the table. You’ve probably saved a bunch of woodworkers a bunch of frustration.
ты гений...и все гениальное простое...как миллионером стану ..миллион подарю тебе ))
Спасибо, бро, жду с нетерпением )) Удачи тебе!
Love the finished product 👍
Made a bunch of quarter inch dowels today with the jig. They are more finicky then the 3/8" dowels. I found the smaller stock size would splinter if I tried to pull the part that was in the drill chuck like I did with the 3/8" dowels. The quarter inch dowels wouldn't take the stress as well. I just cut off the square part. Worked very well once I got it dialed in. I did make a extra set of blocks as my first set had shifted and went back to just a 3/8" starter hole to the quarter inch out hole. The tolerance with the quarter inch dowels is much more picky. I went from having a few store bought dowels to having over a hundred just using my scrap oak, maple, cedar, walnut. The oak gave me the most trouble in the smaller size of dowel. GREAT JIG!
this works better than any dowel maker I've seen and doesn't involve making a difficult to make cutter. Thanks for sharing.
Excellent Video and brilliant Idea. Very well executed
Thanks for sharing I have been looking for a reliable way to make dowels and I think this is awesome.
Nice set up on the sawdust catching
Найкраща приспособа, яка достойна копіювання! Нещодавно придбав дешевого станка та шукаю додаткові приспособлення, для покращення його роботи.
Best and most accurate dowel jig on the tube. Thanks for sharing
You really have done a great job with this one
Amazing idea. Like a hand held lathe.
thanks for the free plans👍
Это тот самый момент, когда на приспособление тратится больше времени, чем на саму работу - и это правильно!
Ещё бы стружкоудаление сверху провести - будет вообще круто! С меня лайк за идею, воплощение и работоспособность! =)
Ваня, при помощи простой лерки нужного тебе диаметра, вставленной в плашку, и зажатую в тиски ты сделаешь тоже самое. И никакой головной боли с изготовлением всяких не нужных " приспособ". Старинный дедовский метод , кстати.
Need to make a fair number of long dowels 16 and 20mm and out of all the dowel making videos this one seems to be the one I need. Thanks for sharing. Andy UK
Супер прибор! Обязательно себе такой сделаю! Огромное спасибо мастеру!
I can't improve upon the comments that are already here, just like I can't improve anything about your dowel device. The fit and finish are second to none. There are a lot of great ideas here on RUclips, but few demonstrate the skills you've shown. Very nice. This could be a real money maker for anyone willing to make dowels. Quality dowels "Not Be Cheap!" They are hard to find and seldom come in a variety of woods.
Plus, chucking a drill onto the finished end would allow you to finish each dowel by pulling the final few inches through... Worth it instead of just cutting off the square end? IDK... Just a thought. Just a little less waste.
Purely magical!
I'm. Attempting. TODAY!. The other jigs where you pound the dowel through metal or even chuck it up to drill are just a royal pain. Too much effort for one stinking 4" dowel. THANK YOU! Hope I can make mine as precise as yours.
This is a Must have!!! Thanks
Tôi cũng đã làm như thế này và thành công,bạn thật tuyệt vời khi chia sẽ video này
Tolle Konstruktion. Danke für das Vid
You have some amazing skills my friend
Не плохой вариант. Возьму на заметку. Спасибо.
You are an excellent carpenter. He is very friendly for making his great achievements available to people who admire his work. Thank you my friend!
Very slick. Well done
Ingenious I'd say. Sweet.
Thanks a lot! Works perfectly 👌
Thought this was a great design and built it, inititially dowels were coming out undersized. Realized that when I marked the high point of my blade, it was in the full up position. Later when using the jig to make dowels, the blade was lower. My saw pivots when raising the blade so the high point was actually further back. Once I adjusted the mark on fence to correspond to the new peak worked like a champ. Apprec I ate you sharing the design.
Very nice.Impressive idea.
Eine sehr gute und simple Konstruktion. Die Genialität liegt hier wohl in der Einfachheit. Eine besondere Hilfe in der Werkstatt. Regt mich zum Nachbau an. BG from Austria
Nicely done 😎
Great video. Yes very helpful, gives me great ideas to adapt this idea to my shop
This is freaking sweet. You're a genius!
Как мне нравится смотреть на все такие столярные работы.))) Я и делатть люблю и креативить. Единственное что не люблю, так это видео монтажём потом заниматься. ))))))
Efective simplicity
Super like this jig. Thanks
The first Dowel maker that work for me , congrats
Thank you, Cristian!
Отличная работа! Всё работает. Не ожидал. Можно работать с различным диаметром. Супер!
Absolutely genius!
That is slick!!!!! Great job!!!
Brilliant design!
Merci bcp pour la vidéo et le partage des plans!!!
Simply wonderful!!!
Thanks,your system is perfect.
My english is quite poor. But is an awesome jig,very useful. Thanks.
Greetings from Chile.
Great Jig. 👍👌
Another great idea. Thanks for sharing!
Excellent idea, thanks for sharing!!
Very good work 👍👍👍👍
Dude! You're a genius! I have a lot of young birch trunks on my ranch. Now I know how to use them .
I appreciate the mention in the description, and I like your version of the jig. Great video.
Bravo super idée
Very clever! Thanks for sharing.
I really like yiu drill press chip collection that is nice
Free PLANS GREAT SUPER ARTICLE
Wonderful build
awesome work!
Brilliant.Best one so far on TY
Very easy to make! Perfect result! I've watched a lot of videos and this is the best dowel making device I've ever seen. So far I have used a metal plate with matching holes. Now I`ll make this dowel maker. THANK YOU VERY MUCH for such a detailed video.
Perfect 👌
What a clever design. Thank you very much for sharing this with us...
Steady. Gan
Beautiful Craftsmanship & Brilliant approach for easy dowell making bro
*You have done all this work beautifully, and most importantly, it is a production product that is widely used in carpentry work.*
Thank you very much for showing this!
I had already created a very 'no nonsense' dowel jig what was working (without the tablesaw), but i kept thinking about one with the tablesaw, came across your video and decided to make it tonight.
I did change some things (because that made it easier for me:
- i did not do your thing with the bolds and wing nut-thingy, i just uses a screw that i can turn in and out (filed the tip of a little)
That saved me a lot of time and i believe it works as well.
Ah, and i had to make the jig to understand why you created the part at 3:07, i thought you used it to make it easier to insert the long stick, but it had a different (better) reason ;-)
I made it tonight, and tried it on one (i only created 1 size for now) and although the top of the stick came out smaller (i think because it was not really centered when entering), the big middle part was perfect.
Thanks again!
Slightly complicated to make, but definitely the best dowel maker I've seen yet, awesome work!!
ماشاء الله تبارك. روعه ماشاءالله تبارك الله
That is better than nice, its' outstanding. Thank you for sharing 👍👍👍👍👍
Awesome tool!!!!!!!!!!!!
Have seen lots of these DIY dowel makers, but this is just on another level...The best, - Thank you.
Brilliant work. Absolute genius. Thanks!
Two thumbs up!
Excellent
Thank you!
Да Вы просто ГЕНИЙ!
Thank you, Once more you have showed me something that I will be pleased to make thanks to you, carry on with your good videos and I will be pleased to make all the great things you are showing me. Thank you great work, Best of luck 🤞 🍀👍
Cool project
Merci pour le partage.
Encore une conception et une réalisation magnifique. Très professionnel !
Salutations de France
That is a cool device.
GENIUS!
Very well done.
Спасибо за видео. Идея не новая, но исполнение отличное. С уважением, Alex.
Outstanding, many thanks
Good idea and nice work! 👍 👌
Nice work
Thank you for sharing!
GOOD INFO I WILL TRY THIS
Excellent. Thanks.
From Algeria.
Awesome 👏 good idea made it
Very good ❤️
Calidad de idea p aser tarugos.gracias p compatir felisitaciones
Good idea!
Good job