Replacing Our RV Suspension | RV Suspension Upgrade!

Поделиться
HTML-код
  • Опубликовано: 4 июл 2024
  • Today we are replacing our RV suspension and making a SIGNIFICANT RV suspension UPGRADE! Two years ago, I replaced our RV leaf springs. At that time, there were major issues with getting parts in a timely manner...so I did the best I could at the time and reused many of the original RV suspension parts. Fast forward to now...I discovered our leaf spring bushings have failed! Originally, I was going to just replace the leaf spring bushings, but upon further inspection, I decided to bite the bullet and do a complete replacement of our RV suspension! This includes new 6 leaf RV leaf springs, new U bolts, MORRyde CRE3000 Equalizer, MORRyde heavy duty shackles, bronze leaf spring bushings, and all new wet bolts from MORRyde. We will also be replacing our tires with Sailun S637 235/85/16 tires! Below are the Amazon links for all of the parts we used when replacing our RV suspension!
    3500 LB Leaf Spring Kit: amzn.to/3NOilPN
    MORRyde CRE3000 Equalizer: amzn.to/445b1Fg
    MORRyde Shackle Kit w/ Bushings: amzn.to/46kH8lP
    How To Repack Your RV Wheel Bearings: • How To Repack The Bear...
    Our must-have RV gear:
    Vremi 50 Pint Dehumidifier: amzn.to/34NLP9X
    Bissell Ion Cordless Vacuum: amzn.to/3eelUv8
    Stainless Steel French Press: amzn.to/3ee1baX
    Electric Kettle: amzn.to/3oPUoJw
    Countertop Ice Maker: amzn.to/3LnDDQh
    Big Berkey Water Filter: amzn.to/2HT6O2s
    Portable Washing Machine: amzn.to/3oOFfbl
    Turkish Bath Towels: amzn.to/2JiH9R0
    17" Blackstone Griddle: amzn.to/2THWRap
    Renogy 200 Watt Portable Solar Panel: amzn.to/3oLVGXZ
    Progressive EMS Surge Protector: amzn.to/3252rIt
    ***Some of the links on this page are Amazon affiliate links. We will earn a small commission if you choose to use these links. This commission comes at no additional cost to you. We only link to and recommend products we use and have had a great experience with!
    00:00 Replacing Our RV Suspension Again!
    01:40 RV Suspension Parts Needed
    03:19 Jacking Up The 5th Wheel
    04:31 Removing The Tires
    05:34 Removing The Leaf Springs
    09:07 Removing The Equalizer
    10:16 Pressing In Leaf Spring Bushings
    13:41 New Shackles Vs Old Shackles...WOW!
    14:31 Installing MORRyde CRE3000 Equalizer
    16:28 Installing New Leaf Springs
    17:29 Installing New Shackles
    19:38 Tighten & Torque
    20:26 Thoughts & Tips
  • ХоббиХобби

Комментарии • 91

  • @johnderbabian6198
    @johnderbabian6198 Месяц назад +3

    I've watched a bunch of these now to prep for my install. By far, your video is the best.
    Some notes from my install.
    1. I replaced all my springs also. I was cautioned not to use larger springs as it could have a detrimental effect (not soft enough to flex).
    2. I found that using a large craftsman screwdriver inserted into the bronze bushing to drive the bushing into the spring worked perfectly and did not deform the bushing. The plastic base of the screwdriver rests on the bushing and does not harm it.
    3. As you did also, I found that if you hang the outboard spring end in the hanger first, it makes it much easier to then align the spring to the axle plate (spring leaf bolt in the center popped into the hole in the plate) plate and ubolts. It then makes it easier to align to the CRE3000.
    4. I notice you put a backup wrench on the back of the wet bolt that attaches the shackle to the CRE3000. Those are pressed in and will not turn.
    5. I used a paint pen on the head of the wet bolts to index the grease hole in the bolt. Makes it much easier to make sure it is indexed to 9 or 3 o'clock when you crawl under to check.
    6. The old bolts are pressed into the hangers (as you said they have shoulders with splines). For me, a hammer didn't do much good. I ended up using an pneumatic hammer with the pointed tip and they literally flew out the back side of the spring!
    Thanks again for your video - well done!

    • @JouppiOutdoors
      @JouppiOutdoors  25 дней назад +1

      Thanks for sharing your experience!

    • @richregan8911
      @richregan8911 20 дней назад +2

      Thanks for posting your notes. I just received my spring kit for a tandem axle trailer. Your tip about installing the bronze bushings with a craftsman screwdriver worked great!!!

  • @davidhake7032
    @davidhake7032 2 месяца назад +2

    Outstanding video. It's not really tough but a bit time consuming when you don't have all the great shop equipment. A couple of things to note for anyone doing this. Be sure you don't get the shackles inverted by accident and every 200 miles or so be sure to recheck torque on the ubolts as they are designed to stretch and will get loose on you. I have found it takes about 4 checks before they no longer require torque check.......and always never overtorque.

  • @marshalld.2825
    @marshalld.2825 Год назад +5

    And with all that strengthening you need to beef up the hangers either weld the V. block in the hanger or wild the bar across the frame between the hangers

    • @JouppiOutdoors
      @JouppiOutdoors  Год назад +1

      Those hangers are definitely one of the weakest points on these 5th wheels!

  • @timothyculliver1993
    @timothyculliver1993 Месяц назад +1

    Great Job, I have changed out my leaf springs in the last few weeks. After talking with a couple people in my local town, one with 45-50 years experience in trailer repair and the other with 20 years in building trailers. Neither one like the bronze bushings, with the quality of springs today, they did not see any difference in length of time between repairs. Sad part was both lasted for about one to two years. This is something more RVer need to know. Keep up the great videos!

    • @JouppiOutdoors
      @JouppiOutdoors  Месяц назад

      Thank you, my last bushings were nylon…I hope these last a bit longer but we will see! Thanks for watching!

  • @LuisPerez-vy6bz
    @LuisPerez-vy6bz 2 месяца назад +1

    Good stuff Sir and thanks for sharing. Looks fairly straight forward, and well worth the time for a DIY project to knock out. 👍🏽

    • @JouppiOutdoors
      @JouppiOutdoors  2 месяца назад +1

      Thanks! And thank you for watching!

  • @adolph289
    @adolph289 10 месяцев назад +1

    AWESOME JOB

  • @stevesingleton2148
    @stevesingleton2148 7 месяцев назад +1

    I've watched this video twice thanks for showing how it's done.

    • @JouppiOutdoors
      @JouppiOutdoors  7 месяцев назад

      You’re welcome! Thanks for watching!

  • @Mike-xo3fi
    @Mike-xo3fi 9 месяцев назад +1

    Nice vide!! Thanks for

  • @zj9119
    @zj9119 11 месяцев назад +1

    Doing this same project this evening on our 2016 GD 30BH fifth wheel. I've already knocked those nylon bushings out using same size socket and a hammer. Thanks for posting this with the helpful tips.

    • @JouppiOutdoors
      @JouppiOutdoors  11 месяцев назад

      You’re welcome and hopefully it goes smoothly!

  • @brianlisec2509
    @brianlisec2509 5 месяцев назад +3

    I did mine last year without removing springs and what helped me a lot with realigning holes was a ratchet strap along with handy pry bars of coarse. Along with these upgrades I strongly suggest adding Sumo Springs and or shock absorbers for a real big difference. Anyway enjoyed your video thank you.

    • @JouppiOutdoors
      @JouppiOutdoors  5 месяцев назад

      I have Timbrens on the truck (like Sumo Springs) and they made a world of difference when towing…I can see where they would benefit the trailer suspension as well. Thanks for watching!

  • @scotz71
    @scotz71 10 месяцев назад +1

    Great job, thanks for all the install and align tips for the shackles and springs. I'm doing this next week when HD shackle kit arrives, and what you showed will save a lot of fit up time. Well done!

    • @JouppiOutdoors
      @JouppiOutdoors  10 месяцев назад +1

      You’re welcome, it’s not incredibly difficult…just a bit time consuming. Good luck with it and thanks for watching!

    • @scotz71
      @scotz71 9 месяцев назад

      Changed my leaf springs out, went from 4 to 5 leafs. It was a job, and your video was a big help. How do you like the 6 leaf springs? Seems like 7000 lb springs on 5000 lb axles is overkill, but after I drove through ND and MT to Glacier NP, makes me wonder if I should have gone with 6 leaf option. Any advice on how 6 leaf is working for you compared to 5 leaf previous upgrade, compared to 4 leaf factory?

  • @jackmason7518
    @jackmason7518 6 месяцев назад +1

    Good Morning. Thank you I plane to install MoRRyde is summer. I will add two cross bars to help over all Thank you. Jack

    • @JouppiOutdoors
      @JouppiOutdoors  6 месяцев назад

      You’re welcome, thank you for watching!

  • @brianbelliveau5551
    @brianbelliveau5551 8 месяцев назад +1

    I have that equalizer on my trailer. It’s made a world of difference. Also put the sumo springs. It’s softened the ride a lot

    • @JouppiOutdoors
      @JouppiOutdoors  8 месяцев назад

      I could definitely tell a difference when towing! Thanks for sharing about the Sumo springs.

  • @tomahawksteak6672
    @tomahawksteak6672 8 месяцев назад +1

    I basically did the same on my tandem sxs trailer. I blocked the frame behind the rear axle and used my tongue jack to get everything inline.

  • @KK-rb6ck
    @KK-rb6ck 8 дней назад +1

    Tighten the nuts or bolts of the suspension components only after lowering the vehicle or, alternatively, jacking up the axle to the loaded position. Otherwise, you will tighten the components at their extreme position.

  • @shawnmancebo1217
    @shawnmancebo1217 2 месяца назад +1

    Great job of getting done with what you have !
    Take a good look at your wear pattern if your tires are wearing on the inside you have bent axles .
    It doesnt matter how loose your suspenion is the suspesion holds the weight and keeps the axle true to the trailer if it allows one side of the axle to fall behind the other side you will get scuffing marks weird patterns but it will be wear all the way across
    The geomertry between your axle and tire doesn't change with worn out loose suspesion unless you have extremely loose bad bearings or your axle is no longer true to factory spec. Which cause inner tire wear from the jonyce it takes hitting pot holes railroad track ect. And if you're loaded heavy something is going to give. Like a big hammer taking a swing something going to give!
    Now with that said over inflated underinflated will make clear wear patterns but will be across the tire on both sides or in the middle from using the trailer brakes
    I hope this helps
    Keep and eye on the wear you might find its time for a freash set of axles

    • @JouppiOutdoors
      @JouppiOutdoors  2 месяца назад

      All great points! Thanks for sharing!

  • @DreamingOutloudRVing
    @DreamingOutloudRVing Год назад +2

    Great job! This is a awesome upgrade. Let us know how it does traveling.

    • @JouppiOutdoors
      @JouppiOutdoors  Год назад

      Thank you! It tows GREAT! We have taken it from Florida to South Carolina and it definitely handles better on those rough roads. The bumps and expansion joints on the bridges feel far less harsh. Thanks for watching!

  • @chrishostetter3610
    @chrishostetter3610 11 месяцев назад +2

    I have the same camper that you have. Installed a set of sumo Springs. They are amazing. I highly recommend you get yourself a set and install them you will not regret it.

    • @JouppiOutdoors
      @JouppiOutdoors  11 месяцев назад

      Thanks for the info, I will definitely look into it!

    • @twk1956
      @twk1956 11 месяцев назад

      Hi Chris! I'm considering the SUMO Springs; can you elaborate as to how they actually improved your towing experience? TIA

  • @lukman8400
    @lukman8400 11 месяцев назад +1

    Thanks! It is a complex job, especially lining things up.
    How do you ensure that the axle is perpendicular to the spring leaves, i.e. 90 degrees? Slight misalignment can make the wheel go slightly right or left. Thanks!

    • @JouppiOutdoors
      @JouppiOutdoors  11 месяцев назад +5

      The leaf springs have an alignment pin that sits in a hole on the axle spring perch. As long as the pin is in the hole, you’re all lined up!

  • @ZonaJim
    @ZonaJim 29 дней назад +1

    PLEASE. Put the majority of the weight of the trailer on Jack stands and only used the levelers as stabilizers. I've worked on these rigs for years and I've seen those levelers bend if there is lateral force applied and the RV is not supported with jack stands or the tires. In addition, stack two tires on their side under the back of the RV. If the RV does fall, this will be your last line of defense from getting crushed to death.

    • @JouppiOutdoors
      @JouppiOutdoors  29 дней назад

      Great points! Thank you for sharing, I will be more mindful of this in the future!

  • @darenaubiephotography8570
    @darenaubiephotography8570 2 месяца назад +2

    Would it not be better to put the grease zirk heads to the wheel side so it is easier to grease in the future? Or does it have to be to the inside?

    • @JouppiOutdoors
      @JouppiOutdoors  2 месяца назад +1

      Definitely considered that, however, it would be awkward and difficult to access them with the wheels on. So I went back to the inside.

    • @darenaubiephotography8570
      @darenaubiephotography8570 2 месяца назад

      @@JouppiOutdoors Makes sense. Thanks for the reply! Great video by the way.

  • @mathieulavoie424
    @mathieulavoie424 9 месяцев назад +1

    If your tire wear is uneven, the issue is not with the leaf spring but with the axle that is too small. I did put bronze bushing on my rig also and they wear out as fast as the nylon bushing.

    • @JouppiOutdoors
      @JouppiOutdoors  9 месяцев назад

      Worn bushings could definitely lead to uneven tire wear as well. Thanks for watching!

    • @rodgraff1782
      @rodgraff1782 8 месяцев назад

      The bronze bushings do not wear out sooner than this thin chicken shit nylon tubes. I’ve proved it. No way, unless you didn’t lubricate them properly.

  • @larryjanson4011
    @larryjanson4011 22 дня назад +1

    you have been lucky as trailer levelers are NOT jack stand rated.

  • @kathyparker8626
    @kathyparker8626 8 месяцев назад +1

    Good job especially being your in the dirt. Is there any reason you have all the zerk fittings facing in instead of out?

    • @JouppiOutdoors
      @JouppiOutdoors  8 месяцев назад

      They would be difficult to access with the tires installed.

  • @28doogie
    @28doogie 2 месяца назад +1

    Just installed the CRE3000 on my Jayco. thanks for the video, helped out alot. Question: How much play should there be with the equalizer when all installed? I tightened to the correct specs, but the equalizer seems to be pretty stiff with little to no play. Just curious about yours or anyones thoughts. Thanks!

    • @JouppiOutdoors
      @JouppiOutdoors  2 месяца назад

      Mine was pretty firm as well. Just made sure it wasn’t binding and it’s been good to go so far. Thanks for watching!

  • @twk1956
    @twk1956 11 месяцев назад +2

    When selecting your upgraded equalizer, did you give any consideration to the Lippert Road Armor equalizer? I'm torn between the two.

    • @JouppiOutdoors
      @JouppiOutdoors  11 месяцев назад +2

      I didn’t really look at anything else. I went based on the reviews from users of the MORRyde system which were great.

  • @starhopper457
    @starhopper457 8 месяцев назад +1

    I may have missed it but how did you check and work the alignment of the axles?

    • @JouppiOutdoors
      @JouppiOutdoors  8 месяцев назад +1

      Everything bolts back in place in the same location so I just got a rough measurement center to center on the hubs and the measurements were the same on the left and right side

  • @campnut6076
    @campnut6076 7 месяцев назад +1

    I am going to do this job in the spring. Were you able to stay with the original length of the shackles or get the longer ones? I wouldn't mind gaining a little more ride height, I'm hoping to stay with my original length 2 1/8" shackles.

    • @JouppiOutdoors
      @JouppiOutdoors  7 месяцев назад +1

      I used the original length shackles. Thanks for watching!

  • @markratliff7991
    @markratliff7991 9 месяцев назад +2

    Curious why the wet bolts do not go in with the grease fittings facing to the outside so they are more accessible?

    • @JouppiOutdoors
      @JouppiOutdoors  9 месяцев назад +2

      I actually considered installing them like that but decided to go with the way they were done at the factory. The fittings on the equalizer would be difficult to get a grease gun on with the tire installed.

    • @TraconWizard
      @TraconWizard 8 месяцев назад

      What he said. My Jayco came w/ CRE 3000 installed facing out. 2 person job to grease but doable.

  • @carlosandrade7439
    @carlosandrade7439 3 месяца назад +1

    By any chance, do you require the generator running or being hooked up to power to run the tv? We have that issue on our 22' Momentun 23G and it's irritating. Would like to figure out how to use the TV on my battery instead just like the audio system.

    • @JouppiOutdoors
      @JouppiOutdoors  3 месяца назад +1

      Yes, the TV is 110v AC power. You would need the generator or shore power plugged in to power it. The audio system runs of the 12v DC power from your batteries. I have a video on how we installed an inverter to power our 110v accessories that may be helpful to check out!

  • @starhopper457
    @starhopper457 7 месяцев назад +1

    A followup if I may... I note these are four leaf springs you are replacing. What did you upgrade and if I may, what is the GVWR of the trailer? I'm working numbers for our trailer and I lean to 7K springs even though the trailer is 11.6K GVWR. A kind gent at eTrailer is suggesting 6k springs but I feel that is at the limit of the springs.

    • @JouppiOutdoors
      @JouppiOutdoors  7 месяцев назад +1

      I went from 4 leaf 3,000lb springs to a 6 leaf 3,500lb spring. The GVWR of our 5th wheel is right at 11,000lbs and our last scale weight was 9,950. It seems like overkill, but towing as much as we do over some really terrible roads has taught us that a beefed up suspension system is better!

  • @stevebeaulieu2617
    @stevebeaulieu2617 9 месяцев назад +1

    Nice video, did you find it hard to take out the leaf spring by just lifting the axle? I mean because you didn't lift the frame first.

    • @JouppiOutdoors
      @JouppiOutdoors  9 месяцев назад

      I lifted the frame with the leveling jacks to the point where the tires were barely touching the ground. That removed the weight from the axle so I could use the floor jack to raise and lower it.

  • @nathanurick8320
    @nathanurick8320 3 месяца назад +1

    Thank you partner for the video, I have a 2013 solitude and want to do this. I noticed your springs were made in China, do you think it’s a good product or is there a USA made leaf that I can buy.

    • @JouppiOutdoors
      @JouppiOutdoors  3 месяца назад

      I haven’t had any issues, seems like a good product. Thanks for watching!

  • @nathanboiros9223
    @nathanboiros9223 3 месяца назад +2

    Adding the beefy springs, dis you notice a trailer height difference? Anything notable?
    Also, the tire that was wearing... any wear on the replacement tires after the suspension upgrade?

    • @JouppiOutdoors
      @JouppiOutdoors  3 месяца назад

      There is a slight increase in trailer height but less than 1” so not really significant. No sign of any abnormal tire wear so far and we have put a lot of miles on it!

    • @nathanboiros9223
      @nathanboiros9223 3 месяца назад

      @JouppiOutdoors that's great to hear. I have this same trailer, 2020 but same version as yours with the dual passenger rear doors and big bunks. I'll be doing this same work over the next month. I'm gathering the tools and parts now to get organized. Your videos are invaluable resources to me. Going to grease the wheel bearing too while the wheels are off (my first time). Your bearing video will help me too. Appreciate you posting links! Because of you I purchased an impact gun. 🤣

  • @nunaya4163
    @nunaya4163 2 месяца назад +1

    Why would you put the grease fittings in the back?

    • @JouppiOutdoors
      @JouppiOutdoors  2 месяца назад

      I get that question a lot. With the tires installed, the fittings would be awkward to access.

    • @nunaya4163
      @nunaya4163 2 месяца назад +1

      @@JouppiOutdoors After looking at my tires I see what you are talking about Thanks

    • @JouppiOutdoors
      @JouppiOutdoors  2 месяца назад

      You’re welcome!

  • @thethiefonthecross9092
    @thethiefonthecross9092 11 месяцев назад +1

    What kind of leaf springs are these and how much did they cost?

    • @JouppiOutdoors
      @JouppiOutdoors  11 месяцев назад

      There is a link in the description to all of the parts I used in this project. Thanks for watching!

  • @nathanboiros9223
    @nathanboiros9223 3 месяца назад +1

    Not trying to be a PIA but you gave some conflicting information that I was hoping you could clarify. At minute 16:25 you pointed to the center bolt on the equalizer and said you torqued it to 65 ft. Lbs. Then at minute 20:18, you pointed to the same bolt and torqued it to 50 ft lbs. Just curious which is the correct torque lbs for the center bolt on the equalizer. Thank you and thanks for giving me the confidence to do this job mysel.

    • @JouppiOutdoors
      @JouppiOutdoors  3 месяца назад

      Good catch on that! The center bolt on the equalizer is indeed 65 ft lbs. The shackle bolts were torqued to 50 ft lbs. Not sure why I pointed to the equalizer…probably about to have a heat stroke doing this job in the Florida sun! Thanks for watching!

    • @nathanboiros9223
      @nathanboiros9223 3 месяца назад

      @JouppiOutdoors that's what I figured but wanted to make sure. Appreciate everything you do!

  • @eddielester3891
    @eddielester3891 6 месяцев назад +1

    What was the total cost for this set up ? I’m looking at a Roadmaster kit and it’s 1800 for entire kit with shock absorbers ? Just trying to make best choice for us . Thx and enjoyed the video

    • @JouppiOutdoors
      @JouppiOutdoors  6 месяцев назад

      I’ve got links in the description to all of the parts. I believe we were at about $750 for everything. Thanks for watching!

  • @trapper4676
    @trapper4676 3 месяца назад +1

    why didn't you install so the grease fittings were oil the outside? Make is easier to grease the bolts.

    • @JouppiOutdoors
      @JouppiOutdoors  3 месяца назад

      With the tires on, it wouldn’t be significantly easier to access.

  • @DennisWintjes2
    @DennisWintjes2 3 месяца назад +1

    Thanks for sharing! Subscribed! Like #326 :) How long did this take? I will be doing this soon on my Arctic Wolf 295QSL8.

    • @JouppiOutdoors
      @JouppiOutdoors  3 месяца назад

      It took about 5 hours including repacking the bearings. Thanks for watching!

  • @marshalld.2825
    @marshalld.2825 Год назад +3

    7-2-2023What about adding shock absorbers! You wouldn’t drive your car without shock absorbers! It’s a sorry state of affairs at the end the street doesn’t realize what a trailer saver they are. Both users and manufacturers.

    • @JouppiOutdoors
      @JouppiOutdoors  Год назад

      Shock absorbers are definitely beneficial. Thanks for for watching!