Great job. Took a shot every time you said Locktight. I died. Sad now. Oh grinding those parts shows your great at these builds. Many wouldn't do this for customers.
found this channel looking for stuff on the Chuckus glad I did you got some great content well edited, good vibes and crammed with information definitely got yourself a new subscriber
I have a gen 1 mad dog ruckus style how much will you charge to stretch it? I’m a female so I need to know how to put the part on the stretch it and make it lower I have a fat back wheel. Can you send me that information please. Love your videos! I have a 50 cc want to make it faster.
At 10:42 you mentioned about the the stock fuel pump. Is there a way to wire it to run it or is it not recommended. And my next question is I have 4 Pieces to powder coat, about how much would I be looking at to spend on all that its frame work and the headlight bracket
I have a question I put a new Camshafts in my 150cc scooter and put a 112 main jet from a 98 main jet and I lost bottom end speed and some top end speed I have 11gram rollers can u help me
Would it be cheaper to buy a ruckus for about $1600 or some and then swap with aftermarket parts? Or build one new from scratch like it seems you are doing? lol
What kind of brand and can give power to my yamaha mio sporty? Im planning to upgrade only the transmission of my scooter. I hope you can give me some idea? Thank u
Hello, I am a young guy from Germany. would like to build a bike here too. Where do I get all the parts needed and who sends them to Germany. especially where do you get such an airride system ??? fg Manuel ps: also like private contact via e-mail. Thank you
DOES ANYONE KNOW HOW TO REMOVE THE REAR OUTPUT SHAFT i thought a c clip held it in but its not on the short side is it under the seal on the long side ???
@@RollingWrench I sent you a picture on Instagram of what mine looks like. It's with the PWJDM pegs so it's a bit different but it should be the same with the pegs you are using. 🤙🏼
Matt, I installed the short axle kit into my gy6. Once I install the axle nut the hub will not move. If I remove the nu the hub will spin freely. Where did I mess up?
I have a Yamaha c3 xf 50 with 120 x 90 x 10 rims I'm going to stretch it and I would like to get some of those rims and the adapter for the rear end shaft I'm going to extend my Yamaha and I want to order some of those rims and tires the 8 inch wide tires I'm rebuilding my Yamaha to make it resemble a Honda ruckus stretched I've been in told that I can only get a Big bore kit and have to use my head to bore it out to make it 75 CC instead of 49 or 50 is this true could you give me information on how to get those rims and tires thank you rolling wrench
Hey whats happening? I'm new here. I just copped a 02 ruckus why a gy6 150 long case in it but I want to purchase a new the whole 150 set with the big bore kit to a 232cc. I want u o DIY. I'd like some pointers if possible.
bro, have you ever encountered a problem with that kind of engine hanger? I mean, that kind of FIXED engine hanger? Is it safe for the engine bushing? thanks
I bought a Honda Ruckus in April of 2018 (Brand New At The Time) and I was wondering why does it die when I give it gas... it will start up no problem...but even after I let it warm up..as soon as I give it some gas it Dies ...any ideas on why it does this would be much appreciated
It sounds like the ruck sat around for a bit and needs a carburetor clean. Here is a link to help with that: www.rollingwrenchdenver.com/products/how-to-clean-a-honda-ruckus-carburetor-full-hd-video
Rolling Wrench, i have a question, i bought a 2009 Ruckus last year that needed a new carborator and battery and it's been running great with no problems.it sat for about 3 weeks so i put a charger on the battery and accidently put the leads on the wrong terminals, it started smokeing and i pulled them off (no more than 5 sec)and now it wont start. i tried using the kick start it but i still get nothing. any ideas one what i might have fried?
@@RollingWrench, ok, will do, but i already checked the 3 i could get to and they were fine but i didnt have a needel nose pliers to check the 2 that i couldnt check which were a 10A and a 20A, I'll check those asap, again thanks
@@RollingWrench Thanks. One more question. If you are building your ruckus from the ground up how do you get them register at your DMV? Thanks again Love the channel
It’s a Sony a6000 with the kit lens. At the time I bought it, it was the fastest focusing camera. It’s getting kinda old now. I think they have the a6400 out now. Thanks for watching !
![GY6 232cc Monster Scooter Engine Build - Case Prep [EPISODE 1]](http://i.ytimg.com/vi/cYpKMt4pD7w/mqdefault.jpg)
Great job.
Took a shot every time you said Locktight. I died. Sad now.
Oh grinding those parts shows your great at these builds. Many wouldn't do this for customers.
found this channel looking for stuff on the Chuckus glad I did you got some great content well edited, good vibes and crammed with information definitely got yourself a new subscriber
Saaweeet! I appreciate you 🙏🏻💯
Just bought my ruckus yesterday, can’t wait to start modding. Also,
8:49 subbed. Also 14:15 double subbed. 20:14 triple subbed.
Great video bro, that engine mounting bracket is ice cold, and the tire is even better. Nice clear video, straight to the point.
Kachi's Kid thanks man! Can’t wait to release the next episode!
can you please add a pic of all the original frame and after for cutting off all the pieces u need to make the mount work properly??
I have a gen 1 mad dog ruckus style how much will you charge to stretch it? I’m a female so I need to know how to put the part on the stretch it and make it lower I have a fat back wheel. Can you send me that information please. Love your videos! I have a 50 cc want to make it faster.
incredible top of the line congratulations
I don't do the Honda Ruckus but I do think spoke tires 12 or 13 inch front and back would look pretty cool
This is cool, you're snappy, a big tank you for putting the time in. I know how long it takes, you're awesome. I think this is gold - you got a sub.
My question so far: Is it possible to fit in a big bore and fat wheel without stretching the wheelbase?
Can you put a fatty wheel on a 2019 PCX 150 and stretch it back 5 inches ???
Where can i buy that fuel pump i really need that bro please tell me i m from india can that pump delivered ?
Where can I find/buy a full honda ruckus frame that a gy6 150cc engine will bolt to.
May I know the wheel's size? The front wheel and rear wheel. Thank you!
Nice vid! ---Where can i get the table you got the ruck on?
Qual é o nome do site onde você compra essas rodas
At 10:42 you mentioned about the the stock fuel pump. Is there a way to wire it to run it or is it not recommended. And my next question is I have 4 Pieces to powder coat, about how much would I be looking at to spend on all that its frame work and the headlight bracket
I have a 2014 jonway that is modeled after the ruckus can I still attempt to do a build like yours?
I have a question I put a new Camshafts in my 150cc scooter and put a 112 main jet from a 98 main jet and I lost bottom end speed and some top end speed I have 11gram rollers can u help me
What do you do with all of the parts that you remove
I have a MP-250-jcl having problems with the vacuum lines on the carburetor can you please help need to know where all lines go
Would it be cheaper to buy a ruckus for about $1600 or some and then swap with aftermarket parts? Or build one new from scratch like it seems you are doing? lol
I'm getting ready to build my gy6 Ruckus. Where is the cheapest place to find red lock tight in bulk?
can this be done on a 2017-2020 model ruckus or are the years important for this type of build?
Very nice! I had a MNNTHBX stem and bar setup on my ruck. I'm thinking I'll go for a drag bar for the next ruck I build. Plus using your FI kit
Ted Sommer sweet! Thanks again for the support 🙏
What kind of brand and can give power to my yamaha mio sporty? Im planning to upgrade only the transmission of my scooter. I hope you can give me some idea? Thank u
Where can I get just the frame ????
Hello, I am a young guy from Germany. would like to build a bike here too. Where do I get all the parts needed and who sends them to Germany. especially where do you get such an airride system ??? fg Manuel ps: also like private contact via e-mail. Thank you
what kickstand is that?
hai bro apakah di indonesia ada nda honda rukus?
DOES ANYONE KNOW HOW TO REMOVE THE REAR OUTPUT SHAFT i thought a c clip held it in but its not on the short side is it under the seal on the long side ???
Why don't you put the kickstand inside the frame? If I'm not mistaken it's designed to stay in place instead of how you got it to stay in place.
I’ll try that, I’ll see if it will work that way. Good looking out!
@@RollingWrench I sent you a picture on Instagram of what mine looks like. It's with the PWJDM pegs so it's a bit different but it should be the same with the pegs you are using. 🤙🏼
Matt, I installed the short axle kit into my gy6. Once I install the axle nut the hub will not move. If I remove the nu the hub will spin freely. Where did I mess up?
What wheels are those or where can I find them???!!!
I have a set in stock :-)
I am also rebuilding and restoring a gy6 bike. Wanting to purchase the parts to modify some. But I don't know how.
Email us I’ll help you out. Rollingwrenchdenver@gmail.com
I have a Yamaha c3 xf 50 with 120 x 90 x 10 rims I'm going to stretch it and I would like to get some of those rims and the adapter for the rear end shaft I'm going to extend my Yamaha and I want to order some of those rims and tires the 8 inch wide tires I'm rebuilding my Yamaha to make it resemble a Honda ruckus stretched I've been in told that I can only get a Big bore kit and have to use my head to bore it out to make it 75 CC instead of 49 or 50 is this true could you give me information on how to get those rims and tires thank you rolling wrench
We are doing a live build series this weekend on the C3 . We have the 76cc already. We will be stretching it live! Tune in:-)
Hey whats happening? I'm new here. I just copped a 02 ruckus why a gy6 150 long case in it but I want to purchase a new the whole 150 set with the big bore kit to a 232cc. I want u o DIY. I'd like some pointers if possible.
Hey dude! Welcome to the ruck world! We have this 232. www.rollingwrenchdenver.com/products/gy6-232cc-water-cooled-complete-engine-kit?ToPasteboard
What screw driver takes out the bolts on the ignition lock
#3 Phillips
bro, have you ever encountered a problem with that kind of engine hanger? I mean, that kind of FIXED engine hanger? Is it safe for the engine bushing? thanks
Where can i find parts for my honda ruckus proyect ?
www.rollingwrenchdenver.com
How do you clean your truck, do you just wipe it down??
I like shine armor:
ruclips.net/video/ctufpFFfqhY/видео.html
When will he start coming to homes once again
I think those days are over :-(
Way off subject, but what camera are you using?
Sony a6400 👌💯
im having trouble finnd a stretch kit for my ruckus fat boy tire where it at on ur site please help
Do you have a 50cc stock GET engine or a GY6? And do you need a full kit or just a mount ?
i got the 150 gy6 on it now it use to be 50cc
I bought a Honda Ruckus in April of 2018 (Brand New At The Time) and I was wondering why does it die when I give it gas... it will start up no problem...but even after I let it warm up..as soon as I give it some gas it Dies ...any ideas on why it does this would be much appreciated
It sounds like the ruck sat around for a bit and needs a carburetor clean. Here is a link to help with that:
www.rollingwrenchdenver.com/products/how-to-clean-a-honda-ruckus-carburetor-full-hd-video
Do you use loctite? And if so, what color do you use?
I use red lock tight on everything! Even tiny screws. They say use blue.... not me! Red!
Bro I would love to have you build me a Trike with a 180 CC. GY6
Do you still have the Vespas? I am looking for a 200. Let me know please.
I don’t have a 200 :-(
My question is I'm 6'4 what is a good set of handle bars to use
I would do motocross bars, or mini apes ?
jajajajajaja me encantan tus videos por lo practico y bueno que eres para explicar la mecanica
HI ... I NEED SOME HELP !
Rolling Wrench, i have a question, i bought a 2009 Ruckus last year that needed a new carborator and battery and it's been running great with no problems.it sat for about 3 weeks so i put a charger on the battery and accidently put the leads on the wrong terminals, it started smokeing and i pulled them off (no more than 5 sec)and now it wont start. i tried using the kick start it but i still get nothing. any ideas one what i might have fried?
Check the fuses
@@RollingWrench, ok, will do, but i already checked the 3 i could get to and they were fine but i didnt have a needel nose pliers to check the 2 that i couldnt check which were a 10A and a 20A, I'll check those asap, again thanks
Jim MCNeil I bet those are your issue. Your not the first one to do that.
Oh yeah always lube it before sticking in ... Never do it dry.
Good tip
Lil spit work too wink wink
Where is the website to WOR Fabrications?
www.worfab.com
@@RollingWrench Thanks. One more question. If you are building your ruckus from the ground up how do you get them register at your DMV? Thanks again Love the channel
Tobbish Holmes you must start with a vin # Honda frame. Basically buy a used frame.
can u ship here in japan?
The kit or bike?
Where did you get your jack under the motor?
Uncensored American I got it years ago. Its made for choppers. Made by k and l.
What camera do you use, that has the fastest focusing I think i have ever seen!! Awesome video!
It’s a Sony a6000 with the kit lens. At the time I bought it, it was the fastest focusing camera. It’s getting kinda old now. I think they have the a6400 out now. Thanks for watching !
@@RollingWrench No, thankyou. Even though you say it's old, it does such a good job for your youtube videos, atleast imo.
awesome build! I'm from Hong Kong, was wondering if I can commission you to build one for me? and ship to Hong Kong? :D Thanks!
I would if you took control of shipping. I don’t know anything about shipping over seas
Put some vasaline on before knocking it in
God damn lock tight😂😂
Ha ha ha ... Sharp as a tack ... You watch lots of Adam Sandler don't you. LMAO. Adam's awesome 👍
Lol 🤘🏻😛😝😛
I have one here in Jacksonville Florida I need help fixing it making it look nice who is around here ?
Good question. I’m not sure in that area.
informative and funny as hell...thank you
I'am from Indonesia
I have ruckus but don't money
I'll tell ya what you're got damn gonna do you're gonna put some got damn lock tite on evry got damn bolt! Lmfao 😂
Lol
Step 1: red loctite step 2: more red loctite
สุดยอดมากๆครับชอบๆ อยากได้ๆอย่างแรง
Why the hell would you not add disc brakes and instead you’re putting on drums it’s just so wrong.! Why would you do that?
Its a different look. You can still lock up the front. They are sufficientl
Plastic shock bolt.....plastic...hilarious....
Lol
I don,t have to listen to a foul mouth person that takes the Lords name ,you can refrain on a public video with youth kids interested.
Boooooo religion!
Where didi you buy that wheel spacer?