Just a FYI, when using Rustoleum paint you must/should use a catalyst. Yes you can buy and use a catalyst for almost any plain oil base paint. The 2 reasons are because the paint has NO UV protection in it AND the paint is weak and soft after drying...in other words the paint can easily be scratched off with a fingernail. The catalyst has the UV protection in it and the catalyst hardens the paint, plus the catalyst adds a glossier wet look to the final look if you use the Wet Look hardener. Plus the catalyst makes it safer and better to wet sand and buff. Most automotive paint stores sell the catalyst. It'l be around 40-50 bucks extra but well worth it. Oh, and the catalyst will keep the paint job lasting a lot longer. I've painted a lot of cars with it and it will last as long as a $200-$500 paint. Plus, you can use lacquer thinner to thin the paint instead of acetone if you want. Most paint is dumb. Acetone helps the paint kick faster. Never use paint thinner/mineral spirits...all you're doing is adding oil, runs, and a lot longer drying time plus it weakens the paint. If you're painting black Rustoleum don't paint over grey primer...use black primer. Rustoleum is slightly transparent and if you paint black over grey primer the black will turn to Mud-looking in any sunlight and look like crap. No matter how many coats you put on it. edit: If you don't have a good spray booth throw some water all around the car on the floor if you want a lot less dust particles floating around and landing on your paint. No such thing as too much water...but not enough won't help you. It really makes a big difference. Paint early in the morning to help avoid bugs because bugs are not flying around yet when it's cold out. Never paint at night because bugs will attract to your lights. Just my experience and .02. Oops another FYI lol...I personally DO NOT USE any kind of liquid grease/oil remover (spray and wipe) on the project before painting. I know the pro's always say to use it but don't. All that shit is, is just another way for them to make more money, plus if it is not done exactly right it can make your new paint wrinkle. What I do is this: On final sanding I make sure I never touch the surface with my skin or hands/fingers (because all of us have oils in our skin). Then I turn on the fan (the one that sucks out dust) and wipe down the entire project with a clean white cotton like a T-shirt and while I'm wiping I'm also blowing with an air nozzle at the same time. Then I wait a few minutes and come back and wipe the entire project down again with a clean tack cloth making sure I have rubber/latex etc. gloves on. Wait a few minutes (while the fan is sucking more dust out) and right before I paint (the paint is already mixed and in the gun) I wipe it down one more time with another clean tack cloth. I use the cheap hardware store tack clothes. The water is already on the floor (make sure you don't splash ANY water on the project surface!) Water will cause fish-eyes and all kinds of problems so be careful. by doing all this you are actually saving yourself a lot of work later...less wet sanding and buffing and if you're lucky NO wet sanding and buffing...maybe just buffing! My quote is this: "if you slow down and have patience you'll get done faster".
Acetone also levels the paint better. Since it evaporates, large looking orange peel dries much flatter than it looks when first sprayed. An axalta rep told me to always cut up to 5% in urethanes for a better bond and flatter finish. Enamels you can go up to 50% given how thick it is out of the can and how much pigment is in the paint. After doing so I'm sold and will always use acetone. Especially after a few fish eye paint jobs from solvent separation due to solvent separating from the paint taking to long long to dry.
Hi, I’ve got some questions for you. We currently prep and paint our trailer frames with a marine epoxy from Proline. It’s a primer then paint. It cost a lot! We’re looking to try something else but not sacrifice quality. Do you think this would be a good option? I’d love to hear your input on the subject. The trailer will be in the sun and put into water. Anything that’ll help or suggestions I’d appreciate very much. We mainly use black and white. Thanks!!!
@@RaceMentally I'm sure you're asking GT's...but IMO it's the prep (sanding, cleaning the metal surface) and the sealer/primer one uses that's the key...more important than the paint...plus making sure the sealer/primer is compatible with the paint used. Some paints will just sit on top of the primer and not "meld" into each other and that's why we see easy chips and scratches. Just my .02
I sprayed some Rust-Oleum last week, dark blue blended with white to make Richard Petty blue. Used acetone as thinner. Looks great, not sure what would happen to the paint if I mixed in a hardner like the MARSON WET LOOK? I sure miss Dupont Centari acrylic enamel was great paint.
Don't forget, you can use a standard enamel hardener in the paint. It really helps with the quality of the cut and buff. I've personally used the PPG hardener with Rust-Oleum black and it really toughens up the paint.
Beautiful job! Not sure why so many are surprised or astounded at painting vehicles with Rustoleum, many truck and several car models for years were painted with single-stage enamel. It wasn't until the mid/late 60's that paints started getting fancier.
but it was automotive enamel. I have been a auto painter since laquer was the main paint used. over 35 years painting. cheap auto paint is 10 times better than rustoleum. you can use Nason eurathane with harder for $200. and last probly 10 years if cared for
You remind me if my friend Sergio Vidrio. He was first my employee many years ago. He became one of my best friends honest as the day is long and a hard worker.
Nice ! I've had good luck with rust-oleum . Thinning with acetone is the way to go . Don't know if you've tried valspar oil enamel hardener , it increases hardness and gloss . Tractor supply sells their own brand of hardener , it's the same stuff . Keep the great videos coming !
Hey man I did a 97 Dodge ram truck with rustolium maroon painted it let it set for 3 days wet sanded it with 800 grit sprayed it with clear coat looks like a 5000 paint job great video 👍
Spray the inside of the trunk while you have it apart, semi gloss black. Will make it look like a very well taken car. You do very nice work. You have a good rhythm to your painting, and seem very patient.
Como mi pistola tiene vaso de 20oz. Lo mas facil es 12oz de pintura, mas 6oz de acetona. La proporcion 2:1, asen 3 partes total. Dividir 20oz (el vaso) por 3 (partes) es poco complicado, pero 18oz se dividen en 6oz por parte. Lo que uses de pintura, echale mitad de acetona
Gonna have to try that rustoleum on my Elco. Probably next summer though. Wish I had shop like yours bro. Great footage. Great work. Always look forward to your videos. I gotta say as I work on my car I always go to youtube to learn. Your teachin me alot bro. I rely on a few channels here on the tube & yours is one of them. Stay up GT! THANK YOU!
Homes my 2 cents, thin your paint a bit more, like even a 1:1 so you'll have a bigger fan helps avoid the dry spot in the center of the roof, uses a touch less paint and a better/higher gloss reading. Also watch your speed and don't do that super quick go over thing you keep doing, it'll fog your final paint and cause more sanding.
Excellent job and we have the key to success, I have painted two cars with rattle can rustoleum and nobody can tell. My part 4 of 5 series shows my technique using rattle can.
I just cant bring myself to paint over a dent especialy when I have the knowledge and means to fix it. For me it would be like running a marathon race that is 24miles and then giving up a half mile from the finish line. 98% if u will. If Im gunna go through all that work to sand and paint the roof I would rather fix that small dent than explain to people why I painted over it. All that being said ....you did a great job it looks amazing.
Many people don't know rustolem has. Been making paint formeny years,,prep and being able to lay it down gives you a quality job,,,,you got the touchbtother
Looks great! What are you using to keep water from compressor mixing with your paint? Please show what you have and the model number of your paint gun.🙏🏻
notice you holding hose with left hand try.n to keep it out of your work run it up your right arm over your sholder then in left hand. more control over hose. just a thout
That's an excellent tip 👍keeps the hose away from the paint and also the spray gun gets pretty heavy after a while(especially when it's full of paint ). Helps control the distance from gun to panel
Rustoleum acrylic lacquer spraycan is one of the best out of the can spraypaints out there for full gloss .. Hichem paints are also near identical to Rustoleum just diffrent labelling
Awesome effort 👌🏽 . Give LVLP SPRAY Guns a try 1.3 or 1.2 mm tip. It levels out more and it suits for a small compressor.much less overspray ,more paint on the job 🙂👍🏽
What works very well for rustilium is 4 parts paint, 3 parts acetone, and one part hardener. Drys fast and hardens very well. Much more glossy as well with hardener
Mon just looking how you laid the black down after it had dried I would have used masking tape to make some patterns then laid a lace sheet over that. Shot some silver paint over that then some flake or metallic. That would have took care of any dents and practice with patterns and Kustom paint job would have went with the pink bottom. Yes work with what you got you don't have to have a whole lotta money to make cool art work.
It takes at least two days to fully dry. I wouldn’t touch it for four. An acquaintance painted his Triumph with rattle cans of this stuff. It looked great but took him a VERY long time to do all the pieces right. Remember, enamel doesn’t like to be sanded at all and polishing should probably wait six months. Next to powder coating it is my choose for all suspension and undercarriage surfaces.
I used a lot of rustoleum.. because I paint a lot of trailers. Rustoleum..is good paint, and it flows very nice even wit cheap spray guns, you can get really nice results with it. The only problem is the shine does not hold up for long. After a few months it becomes dull as it comes out of the can. Perhaps adding some harder, or putting some kind of clear coat over it, will last longer. Great paint job though!!!
Thank you! On cars, washing them regularly and waxing them helps keep the shine! Very good paint on my opinion. You can paint almost any vehicle with less than $50
Saludos desde puerto rico , me gusta tu contenido llevo tiempo suscrito a tu canal , pero no entiendo el ingles pero igual los veo , seria bueno que hicieras videos en español tambien espero leas mi comentario gracias
Ive been doing it for many years. Rustoleum is about $10 a quart. Sometimes I find them on clearance for $1 each. That's how I painted my Mitsubishi (again) for less than $20 I don't listen to people who say otherwise. If they aren't helping me sand, or paint it for me.. then there shouldn't be any reason for me to care what they think 🤷🏻♂️
@@GTsPerformance As others have said you are getting good results but if you are going to this much trouble to prep and paint seems silly not to fix a few small dents. I have painted my farm tractor with single stage paint and no hardener ... that was a mistake since even a year later it scratches easily. The paint was not Rustoleum but rather Ace Hardware brand. Please let us viewers know how easily this comes off (or doesn't). Also looked to me when you were spraying roof you might have been starting to get fisheyes? Could that be from oil/wax on surface or was that just an optical illusion?
You can use auto paint catylist/Hardner in the paint. Then it’ll dry like auto paint and it’ll cure properly. Do 2 to 1 then add .5 of the catalyst. Get the medium speed. The cheapest stuff your local auto paint supply jobber has brand doesn’t matter.
Like how it came out I seen lot of your videos you enjoy painting have you tried adding camulus Japanese dry to the Rust-Oleum have you tried to reduce it with mineral spirits if so what was the mix
I subscribed... I just bought a 92 Yukon to build on my channel... Its already black but i want to repaint... Your paint came out good so i am going to do mine the same way
Thank you, I appreciate the sub! 🙏🏼 I have plenty of videos on rustoleum, and even how to buff. If anything else, just ask in any video. I try respond the best I can
In my limited experience Rustoleum gloss black spray paint didn't age or weather very well after I painted the rear wiper blade on our GMC Safari. It turned a dull black after about a year or so. Not sure why but it's kind of made me weary of using it to paint anything that's going to be outside in the sun.
Just a FYI, when using Rustoleum paint you must/should use a catalyst. Yes you can buy and use a catalyst for almost any plain oil base paint. The 2 reasons are because the paint has NO UV protection in it AND the paint is weak and soft after drying...in other words the paint can easily be scratched off with a fingernail. The catalyst has the UV protection in it and the catalyst hardens the paint, plus the catalyst adds a glossier wet look to the final look if you use the Wet Look hardener. Plus the catalyst makes it safer and better to wet sand and buff. Most automotive paint stores sell the catalyst. It'l be around 40-50 bucks extra but well worth it. Oh, and the catalyst will keep the paint job lasting a lot longer. I've painted a lot of cars with it and it will last as long as a $200-$500 paint.
Plus, you can use lacquer thinner to thin the paint instead of acetone if you want. Most paint is dumb. Acetone helps the paint kick faster. Never use paint thinner/mineral spirits...all you're doing is adding oil, runs, and a lot longer drying time plus it weakens the paint. If you're painting black Rustoleum don't paint over grey primer...use black primer. Rustoleum is slightly transparent and if you paint black over grey primer the black will turn to Mud-looking in any sunlight and look like crap. No matter how many coats you put on it.
edit: If you don't have a good spray booth throw some water all around the car on the floor if you want a lot less dust particles floating around and landing on your paint. No such thing as too much water...but not enough won't help you. It really makes a big difference. Paint early in the morning to help avoid bugs because bugs are not flying around yet when it's cold out. Never paint at night because bugs will attract to your lights. Just my experience and .02.
Oops another FYI lol...I personally DO NOT USE any kind of liquid grease/oil remover (spray and wipe) on the project before painting. I know the pro's always say to use it but don't. All that shit is, is just another way for them to make more money, plus if it is not done exactly right it can make your new paint wrinkle. What I do is this: On final sanding I make sure I never touch the surface with my skin or hands/fingers (because all of us have oils in our skin). Then I turn on the fan (the one that sucks out dust) and wipe down the entire project with a clean white cotton like a T-shirt and while I'm wiping I'm also blowing with an air nozzle at the same time. Then I wait a few minutes and come back and wipe the entire project down again with a clean tack cloth making sure I have rubber/latex etc. gloves on. Wait a few minutes (while the fan is sucking more dust out) and right before I paint (the paint is already mixed and in the gun) I wipe it down one more time with another clean tack cloth. I use the cheap hardware store tack clothes. The water is already on the floor (make sure you don't splash ANY water on the project surface!) Water will cause fish-eyes and all kinds of problems so be careful. by doing all this you are actually saving yourself a lot of work later...less wet sanding and buffing and if you're lucky NO wet sanding and buffing...maybe just buffing! My quote is this: "if you slow down and have patience you'll get done faster".
Acetone also levels the paint better. Since it evaporates, large looking orange peel dries much flatter than it looks when first sprayed. An axalta rep told me to always cut up to 5% in urethanes for a better bond and flatter finish. Enamels you can go up to 50% given how thick it is out of the can and how much pigment is in the paint. After doing so I'm sold and will always use acetone. Especially after a few fish eye paint jobs from solvent separation due to solvent separating from the paint taking to long long to dry.
Hi, I’ve got some questions for you. We currently prep and paint our trailer frames with a marine epoxy from Proline. It’s a primer then paint. It cost a lot! We’re looking to try something else but not sacrifice quality. Do you think this would be a good option? I’d love to hear your input on the subject. The trailer will be in the sun and put into water. Anything that’ll help or suggestions I’d appreciate very much. We mainly use black and white.
Thanks!!!
@@RaceMentally I'm sure you're asking GT's...but IMO it's the prep (sanding, cleaning the metal surface) and the sealer/primer one uses that's the key...more important than the paint...plus making sure the sealer/primer is compatible with the paint used. Some paints will just sit on top of the primer and not "meld" into each other and that's why we see easy chips and scratches. Just my .02
@@coherantbliss3483 I was asking you. I’m not paint expert and need some help in the department of paint.
I sprayed some Rust-Oleum last week, dark blue blended with white to make Richard Petty blue. Used acetone as thinner. Looks great, not sure what would happen to the paint if I mixed in a hardner like the MARSON WET LOOK? I sure miss Dupont Centari acrylic enamel was great paint.
Don't forget, you can use a standard enamel hardener in the paint. It really helps with the quality of the cut and buff. I've personally used the PPG hardener with Rust-Oleum black and it really toughens up the paint.
what's about the ones they sell in spray can,,does it give the same result?
My brother used to paint he's cars with rustoleum only. If done right they look awesome. Looks great man.👍🏻
👒
I really liked the music choice for watching you paint this.
I’m assuming you are being sarcastic. The music intro is awful and it’s still terrible while he works
Looking good! I don't think anyone will believe this was rustoleum paint after it is finished.
If I didn't see him do it I wouldn't believe it
Definitely won’t, my rustoleum paint came out 100 times worst than his! Great job!
They will after 8-12 months in the sun and weather.
@@ee4231 most people realize that without 2k clear it will fade
@@ee4231 had the same paint on my civic for 3 years now it looks as go as the day it was sprayed. No clear on it either
Beautiful job! Not sure why so many are surprised or astounded at painting vehicles with Rustoleum, many truck and several car models for years were painted with single-stage enamel. It wasn't until the mid/late 60's that paints started getting fancier.
but it was automotive enamel. I have been a auto painter since laquer was the main paint used. over 35 years painting. cheap auto paint is 10 times better than rustoleum. you can use Nason eurathane with harder for $200. and last probly 10 years if cared for
@@w124mercedes7 where can I buy Nason paint?
I truly am impressed with your attention to detail. Well done. Peace and prayers
Attention Detail are you kidding me, he has easy to fix dents al over the car.
That is awesome. When it gets cut and polished, it's going to be spectacular.
¡Saludos desde Costa Rica!
Yup, exactly! I just try to lay the paint as best that I can so the cut and buff wont be hard work
Saludos 🙏🏼
Nice work... and groovy music.
You remind me if my friend Sergio Vidrio. He was first my employee many years ago. He became one of my best friends honest as the day is long and a hard worker.
Nice ! I've had good luck with rust-oleum . Thinning with acetone is the way to go . Don't know if you've tried valspar oil enamel hardener , it increases hardness and gloss . Tractor supply sells their own brand of hardener , it's the same stuff . Keep the great videos coming !
Jbni
Hm
Getting ready to paint my 89 Dodge Dakota. You vids really help. Keep up the great knowledge sharing!! Kudos my friend!!
Hey man I did a 97 Dodge ram truck with rustolium maroon painted it let it set for 3 days wet sanded it with 800 grit sprayed it with clear coat looks like a 5000 paint job great video 👍
Thanks .I wondered if Rustoleum paint could be used for painting a car..Great video.Good job.
Looks good maybe do the whole car in gloss black
Dude it looks great you just gave me an idea for my pickup truck.
Nice job with foldable paint keep the good work and content coming 👌 👍 😀 👏
Spray the inside of the trunk while you have it apart, semi gloss black. Will make it look like a very well taken car.
You do very nice work. You have a good rhythm to your painting, and seem very patient.
Your work speaks volumes!!! Great job.
🧐🌲👍
Niiice...preps are 90% of the job😊
fantastic job mate loved the video and music ,blessed .
Keep it rolling...saving cash!!
Who needs bondo. When 32 coats of paint is just as good.
Cual es la proporción para mixtear?
Por ejemplo: 2:1. Y que clase de reductor usa?. Por su respuesta muy agradecido.
Como mi pistola tiene vaso de 20oz. Lo mas facil es 12oz de pintura, mas 6oz de acetona.
La proporcion 2:1, asen 3 partes total. Dividir 20oz (el vaso) por 3 (partes) es poco complicado, pero 18oz se dividen en 6oz por parte.
Lo que uses de pintura, echale mitad de acetona
Porchswing
😅
If you don't like the man's paint jobs why are you watching 🤷
Gonna have to try that rustoleum on my Elco. Probably next summer though. Wish I had shop like yours bro. Great footage. Great work. Always look forward to your videos. I gotta say as I work on my car I always go to youtube to learn. Your teachin me alot bro. I rely on a few channels here on the tube & yours is one of them. Stay up GT! THANK YOU!
I like this guy he’s honest and nice and took his time to film and edit a video for us to learn 🤩🤩🤩🤩🤩⭐️⭐️⭐️⭐️⭐️⭐️⭐️⭐️⭐️
Good job like you said it is an old car no car is perfect but for sure it does look better then it did before.
hhhhhhhhhlllllllllllllhhhhhhhhhvhhhejdgbdefr
This looks dope boss! I'm glad you went with the gloss black. It pulls it together. Even before a cut and buff this is looking shiny!
Good information and detail mate, good to know from a novices perspective...
Cheers from London England 👍
Damn man that looks good, I bought a can of that jet black Duplicolor today but I’m going to take that shit back and buy the rustoleum.
Homes my 2 cents, thin your paint a bit more, like even a 1:1 so you'll have a bigger fan helps avoid the dry spot in the center of the roof, uses a touch less paint and a better/higher gloss reading.
Also watch your speed and don't do that super quick go over thing you keep doing, it'll fog your final paint and cause more sanding.
What are you talking about he did excellent job some ppl are amazing
Excellent job and we have the key to success, I have painted two cars with rattle can rustoleum and nobody can tell.
My part 4 of 5 series shows my technique using rattle can.
Yeah right...I'm sure the bodywork it top notch too.
I just cant bring myself to paint over a dent especialy when I have the knowledge and means to fix it. For me it would be like running a marathon race that is 24miles and then giving up a half mile from the finish line. 98% if u will. If Im gunna go through all that work to sand and paint the roof I would rather fix that small dent than explain to people why I painted over it. All that being said ....you did a great job it looks amazing.
True
Right on brother
Especially gloss black.
A marathon is 26.2 miles
The man explained his reason. It's his car not yours. Do u on your projects
Looks good, smooth coverage. 👍
Many people don't know rustolem has. Been making paint formeny years,,prep and being able to lay it down gives you a quality job,,,,you got the touchbtother
Hey GT. That is looking killer so far. Thanks for sharing.🍁👍👍
Thanks Andy! 🙏🏼
Going to paint my hood, roof, and trunk with that same paint. Great job Man! That really looks nice!! ✌
It's so satisfying
Tape skills are dope!
I bought one of those kobalt guns but have been nervous to use it. Seems like you do just fine with it.
Nice video. Now i know what to do with my car. Thanks ! 😊
Those were more than 10 coats.😂🤣 Thanks for the video. 👍🏿
Looks good fella keep up the great content enjoy your work
I appreciate it 🙏🏼
A real artist.
I think you do a great job brother, I like doing it to keep up the good work God Bless
Looks good
Nice contrast with the black and the pepto.
I think the front bumper gives the whole attitude of this car. Once its done.. 🔥🔥
Very impressive. I'm going to try it on my 55 chevy. It will look better, and not break the bank! Thanks.
Looks great! What are you using to keep water from compressor mixing with your paint? Please show what you have and the model number of your paint gun.🙏🏻
That paint job is top notch. Probably didn't have to polish it either since the gloss came out very professional.
A master at work
Very nice job
I love this paint scheme. Great job man. I wish you lived closer to NY, I’d hire you to help me paint my corvette.
Thanks brother! No need to pay me to work on your car.. you've been supporting my channel, and that matters to me🙏🏼
@@GTsPerformancemaybe when this COVID madness is over we can talk. That would make some great content for your channel.
I live in ny also. By lake George.
Good job keeping it simple and a good three coats gives cut depth for wet and clear and desert sunfor two weeks looks like a pro
notice you holding hose with left hand try.n to keep it out of your work run it up your right arm over your sholder then in left hand. more control over hose. just a thout
That's an excellent tip 👍keeps the hose away from the paint and also the spray gun gets pretty heavy after a while(especially when it's full of paint ). Helps control the distance from gun to panel
You've got skills sir that looks great
Looks awesome 🤙🏼
Hey...for a minute I thought you were Cub Swanson the MMA UFC fighter. Good video, thanks for sharing.
I've painted a couple cars with Rustoleum and they looked good for about a year and a half then the sunshine took it's toll on it.
Never had this problem. Lol same paint job front my civic for 3 years and still is as shiny as day one. And it stays outside
@@lonewolftech What mix ratio did you use?
Rustoleum acrylic lacquer spraycan is one of the best out of the can spraypaints out there for full gloss .. Hichem paints are also near identical to Rustoleum just diffrent labelling
Looks really good man!!!!
Many thanks, bro 🙏🏼
Looking good bro. Greetings from Oklahoma
Came out great with them 6 coats!! Looks awesome bro
Saludos yo también soy de Puerto rico sería buena idea la del amigo 😃. Pero tengo que decirte que se ve brutal el carrito me gusta 👍🔥🔥👊.
Great work looks great
Excellente buddy..
Love it, even though you didn't fix little dents. 100% better..
Buen trabajo bro 👍 keep doing it estoy loco por verlo ya terminado
Wow that came out nice !
That had me in a trance, you’re talented man
Looks great man!
Much appreciated 🙏🏼
Looks AWSOME!
Easy to use for beginners and very good durability nothing like old classic enamel
Awesome effort 👌🏽 . Give LVLP SPRAY Guns a try 1.3 or 1.2 mm tip. It levels out more and it suits for a small compressor.much less overspray ,more paint on the job 🙂👍🏽
Nice paint job!
What works very well for rustilium is 4 parts paint, 3 parts acetone, and one part hardener. Drys fast and hardens very well. Much more glossy as well with hardener
What hardner and where can I get it?
@@reowhite4862 It's called enamel paint hardener. Most hardware stores have it. If not you can get it online
@@reowhite4862 Krylon Farm Paint hardener or Majic Catalyst hardener, both can typically be gotten at farm/tractor supply stores.
Mon just looking how you laid the black down after it had dried I would have used masking tape to make some patterns then laid a lace sheet over that. Shot some silver paint over that then some flake or metallic. That would have took care of any dents and practice with patterns and Kustom paint job would have went with the pink bottom. Yes work with what you got you don't have to have a whole lotta money to make cool art work.
Man, that looks awesome! Good job!
It takes at least two days to fully dry. I wouldn’t touch it for four. An acquaintance painted his Triumph with rattle cans of this stuff. It looked great but took him a VERY long time to do all the pieces right. Remember, enamel doesn’t like to be sanded at all and polishing should probably wait six months. Next to powder coating it is my choose for all suspension and undercarriage surfaces.
I used a lot of rustoleum.. because I paint a lot of trailers.
Rustoleum..is good paint, and it flows very nice even wit cheap spray guns, you can get really nice results with it. The only problem is the shine does not hold up for long. After a few months it becomes dull as it comes out of the can. Perhaps adding some harder, or putting some kind of clear coat over it, will last longer. Great paint job though!!!
Thank you!
On cars, washing them regularly and waxing them helps keep the shine!
Very good paint on my opinion. You can paint almost any vehicle with less than $50
I've owned 2 of these mirage enjoyed both of them fun cars ......they are getting kinda rare you don't really see them anymore
Looks very good!!!! I always thought the mix was 3 to 1....3 parts paint one part acetone... My bad.
seeing as how good it Looks, My choice is clear, Gloss Black Rust-Oleum for my Dodge Omni GLH clone!
2-1 looks like a good mix
I need like that
great job bud!
Nice job bro im about to do this with tremclad mix to do you add hardener or japan dryer
Love the Mitsubishi videos - should be called The Sakura Special 🌸 ( sakura especial)
Thanks, I'll keep them coming! That "Sakura" does sound more settling than the indigestion relief!😄 the flower, not the anime
Bro keep up the great work! It looks clean, nice setup too!!!
It came out great
Saludos desde puerto rico , me gusta tu contenido llevo tiempo suscrito a tu canal , pero no entiendo el ingles pero igual los veo , seria bueno que hicieras videos en español tambien espero leas mi comentario gracias
Muchisimas gracias amigo. Disculpa, aver si este proximo video le meto un poco eapañol. Ay le mando saludos, y gracias por ver mi canal 🙏🏼
God job Gracias exelente
@@GTsPerformance hola campeon en que lugar pintas
I was wondering if I could use rust oleum on an old vehicle that doesn’t have to be perfect? Thanks for verifying!
Ive been doing it for many years. Rustoleum is about $10 a quart. Sometimes I find them on clearance for $1 each. That's how I painted my Mitsubishi (again) for less than $20
I don't listen to people who say otherwise. If they aren't helping me sand, or paint it for me.. then there shouldn't be any reason for me to care what they think 🤷🏻♂️
@@GTsPerformance As others have said you are getting good results but if you are going to this much trouble to prep and paint seems silly not to fix a few small dents. I have painted my farm tractor with single stage paint and no hardener ... that was a mistake since even a year later it scratches easily. The paint was not Rustoleum but rather Ace Hardware brand.
Please let us viewers know how easily this comes off (or doesn't). Also looked to me when you were spraying roof you might have been starting to get fisheyes? Could that be from oil/wax on surface or was that just an optical illusion?
Te quedo perron un buen trabajo 👍
Looks good brother,keep up the good works.
You can use auto paint catylist/Hardner in the paint. Then it’ll dry like auto paint and it’ll cure properly. Do 2 to 1 then add .5 of the catalyst. Get the medium speed. The cheapest stuff your local auto paint supply jobber has brand doesn’t matter.
Looking good
Like how it came out I seen lot of your videos you enjoy painting have you tried adding camulus Japanese dry to the Rust-Oleum have you tried to reduce it with mineral spirits if so what was the mix
I subscribed... I just bought a 92 Yukon to build on my channel... Its already black but i want to repaint... Your paint came out good so i am going to do mine the same way
Thank you, I appreciate the sub! 🙏🏼 I have plenty of videos on rustoleum, and even how to buff. If anything else, just ask in any video. I try respond the best I can
Great job! Looks awesome
In my limited experience Rustoleum gloss black spray paint didn't age or weather very well after I painted the rear wiper blade on our GMC Safari. It turned a dull black after about a year or so. Not sure why but it's kind of made me weary of using it to paint anything that's going to be outside in the sun.
Needs clear to protect from UV
The person who wrote that long essay, how do i get in contact with you, awesome stuff that you mentioned! Big shout from KaapStaad in Suid Afrika
Awesome last year during the pandemic i did my 89 mustang gt the same way.
Very impressive work. Thanks for sharing. Saludos.