Great content as usual buddy. Congrats on the 4k Dan. Wasn't that long ago you were stressing about the 2k debacle. Was a lot quicker to 4. I was always very confident for you. Well deserved mate..
Well spotted mate. I don’t like opentherm, it causes more problems than it’s worth. When you get a call back because they aren’t happy with the curve you’ve set 😂
I got that with weather comp and the ifos but I've never had a complaint on opentherm. The eph adjusts all the flow temperatures automatically with the load compensation. Actually saves money on gas in my experience. Baxi is all we fit so everything is done via opentherm
I can’t honestly remember on this one. But not going to lie, it was measured off a radiator next door, then guessed 20mm of board adhesive and 12mm board, then whatever finished surface to the centre of the radiator tail.
Tidy job Ben!😂 ive been debating getting the wireless kane temp clamps but worried the bulk will stop them getting into the internal flow and returns inside boilers, ever found them to be an issue?
They are a bit bulkier these ones you’re right DAN 😂 but always managed to get them Inside the boiler, I’ll show you next time 🙏🏽🙏🏽 although these are tpi, not sure if the Kanes are any smaller or bigger.
So I finally hit 4K subscribers! All down to
You lovely lot! Thanks for the support everyone. But don’t forget to like this video too ;) ❤
Congrats on the 4k Dan 🔥🔥🔥 great video 👊🏾
Thank you buddy! Cheers for the support as always mate.
Main eco combi is king
Absolutely matey! 💪🏼
Nice work Dan. Well done mate. I need to start using the liquid ptfe you and Luke are always using it.❤😂
Haha. Yeh it’s good stuff mate. Just takes a bit to gain the trust in it haha. Thanks mate
Heat camera is well impressive, could see the pipe runs 🎉
Yes mate it is at times, although it doesn’t always show the runs under certain floors.
You’ve come on loads with subscribers!👍well done mate ! Keep it going!!
Cheers buddy! Hopefully plenty more will
Join too! Thanks for the support mate!
Love this project, cannot believe the transformation ❤
Cheers mate. Going to look really smart when it’s done!
Nice one on the 4k Dan,
Brilliant finish on that job
👍👍🤜🤠
Thanks Tony! It’s down to you guys supporting the channel 💪🏼💪🏼💪🏼
I really can’t wait for you complete this project and soak in the accomplishment. Congrats on reaching 4k.
Thank you for another great video DAN 😂
It’s not far off now at all mate. Broken its back now! But I can’t wait to see it finished either! Thanks for your support mate!
❤ gonna look smart once completed
Thanks Paul, be glad to see it finally finished haha.
Great content as usual buddy. Congrats on the 4k Dan. Wasn't that long ago you were stressing about the 2k debacle. Was a lot quicker to 4. I was always very confident for you. Well deserved mate..
Thanks mate, it’s down to
Viewers like yourself watching and commenting week in week out 🙏🏽🙏🏽
Congrats on the 4k mate
Thank you mate! Cheers for the support to get there!
Lovely job my man!
Thanks Very much Colin! 💪🏼
Tidy work man 🤝🏻
Thank you very much matey!
Why don't you wire the eph up on opentherm? Enjoyed the video 👍
Well spotted mate. I don’t like opentherm, it causes more problems than it’s worth. When you get a call back because they aren’t happy with the curve you’ve set 😂
I got that with weather comp and the ifos but I've never had a complaint on opentherm. The eph adjusts all the flow temperatures automatically with the load compensation. Actually saves money on gas in my experience. Baxi is all we fit so everything is done via opentherm
@@silvergrim I’ll give it another go on the next boiler mate. 💪🏼 cheers for the advice mate
V2 plus man the best
It is good like, just the brush is shite haha
yeah never reaches bottom of pot@@Heatking
Can I ask. Do you do a. Minimum. And maximum tests on boiler. And a flue integrity test. Thanks
I do, or do you mean can I show you?
Screw to flue up ?
Yeh the flue elbow and the boiler turret. 💪🏼
why no classiseal down the short edge?
It’s having a glass panel down there. It doesn’t go to the corner of the wall mate. Show you on 2nd fix :)
Great video mate, what distance do u use for the radiators for the valves for 1st fix outta the wall? As urs were spot on
I can’t honestly remember on this one. But not going to lie, it was measured off a radiator next door, then guessed 20mm of board adhesive and 12mm board, then whatever finished surface to the centre of the radiator tail.
Tidy job Ben!😂 ive been debating getting the wireless kane temp clamps but worried the bulk will stop them getting into the internal flow and returns inside boilers, ever found them to be an issue?
They are a bit bulkier these ones you’re right DAN 😂 but always managed to get them
Inside the boiler, I’ll show you next time 🙏🏽🙏🏽 although these are tpi, not sure if the Kanes are any smaller or bigger.
🤘😎🤘🫖☕️
Thanks Wayne! 🙏🏽
First
💪🏼💪🏼💪🏼