Now do all of the small block engines no matter who makes them have those 2 tabs that you cut down in the beginning of the video in the same exact spots ? Or is this only going to fit properly on Tillotson Engines ? Do I need to go double check my 196cc OMB Warehouse Engine before ordering this to make sure the screw holes are in the same place as yours are ?
Yes this fits “all” small block gx200 engines and clone of it. Including gx200 / predator 212 and predator 212 hemi engines / predator 224/ tillotson 212 , 225, 236 etc… / Lifan engines and all clones in that class.
Do you know the measurement center to center on the coil bolt holes on the block? I’m willing to try using this on my star if it’s close. There is a little meat to mess with on the mounting bracket.
Paul do you have one for a 420 china clone? Also looking for a 95mm poor 101 mm piston and sleeve I would like to make a 550 CC if possible. I have a 69 mm stroker crank now and a r c connecting rod. I asked you before about a piston you never got back to me you said you were going to look.
But I will say it’s more work that your prob willing to do. Sometimes wrist pin sizes and compression heights don’t match the main stream stuff so you’ll most likely need to be very well versed in these engines.
@@paulskartslifan4206 been building dragcars for years and my engine machinist builds jr dragster motors as well his son was track champ and national champ. He knows small engines. He did all my machine work for my 23t altered 452 cube mopar on enderle alky injection. I built the engine 900 horsepower. This engine will not be a race engine just going into a motorbike to drive around town. I don't have a cell phone to text you from. It only works as a computer because I have Wi-Fi
Yo paul. I got this tecumseh. I know it's not ideal. But I can fabricate dam well. Tecumseh h60 flathead external ignition. Btw you think i should buy one and give it a try?😅
Very well made and high quality piece! A much better option to dial in the timing rather than timing keys. Thanks for sharing!
Thanks man
Awesome idea on those engines, make's adjustment way easier.
Yea it’s amazing
Hi, I've been following your channel for a long time, I've shared it very well, hello Vietnam
Awesome man ♥️
Now do all of the small block engines no matter who makes them have those 2 tabs that you cut down in the beginning of the video in the same exact spots ? Or is this only going to fit properly on Tillotson Engines ? Do I need to go double check my 196cc OMB Warehouse Engine before ordering this to make sure the screw holes are in the same place as yours are ?
Yes this fits “all” small block gx200 engines and clone of it. Including gx200 / predator 212 and predator 212 hemi engines / predator 224/ tillotson 212 , 225, 236 etc… / Lifan engines and all clones in that class.
It's good to be adjustable.
Agreed 🤣💪✅
Do you know the measurement center to center on the coil bolt holes on the block? I’m willing to try using this on my star if it’s close. There is a little meat to mess with on the mounting bracket.
Text me and I’ll check tomorrow for you. 781-492-7358
Paul do you have one for a 420 china clone? Also looking for a 95mm poor 101 mm piston and sleeve I would like to make a 550 CC if possible. I have a 69 mm stroker crank now and a r c connecting rod. I asked you before about a piston you never got back to me you said you were going to look.
Yea I have big pistons .. text me 781-492-7358
But I will say it’s more work that your prob willing to do. Sometimes wrist pin sizes and compression heights don’t match the main stream stuff so you’ll most likely need to be very well versed in these engines.
@@paulskartslifan4206 been building dragcars for years and my engine machinist builds jr dragster motors as well his son was track champ and national champ. He knows small engines. He did all my machine work for my 23t altered 452 cube mopar on enderle alky injection. I built the engine 900 horsepower. This engine will not be a race engine just going into a motorbike to drive around town. I don't have a cell phone to text you from. It only works as a computer because I have Wi-Fi
Yo paul.
I got this tecumseh.
I know it's not ideal. But
I can fabricate dam well.
Tecumseh h60 flathead external ignition.
Btw you think i should buy one and give it a try?😅
Maybe .. I’m sure you can try to modify it if needed. Let me know how it works out
@@paulskartslifan4206
Thanks. Will do.
What's the price on this?
www.paulskarts.com/product/adjustable-ignition-coil-bracket-kit-new-small-block-includes-hot-coil-pre-sale-limited-quantity/682?cp=true&sa=false&sbp=false&q=true
Paulskarts.com
www.paulskarts.com/product/adjustable-ignition-coil-bracket-kit-new-small-block-includes-hot-coil-pre-sale-limited-quantity/682?cp=true&sa=false&sbp=false&q=true
Sucks you gotta cut the block