Since most of your tutorials are made with the Flip 32 F3 Omnibus boards , I've changed all 4 of my quads to this board..Works beautifully for the price and OSD is nice also ...Thanks for all the hard work being done , its greatly appreciated believe me !!
Thanks guys. Yea I did the same thing. All but one of my quads are running F3 or F4 Omnibus boards. As small as 122mm builds to as big as a 650mm GPS build. Great all around FC.
Dominik this comment should be featured in the video or in the description. I was about to unsolder this receiver but I noticed this comment. Thanks man! BTW. Did you checked the real range? I have TGI - i10 and me previous receiver that was supposedly be a >300m like this one but this previous receiver had telemetry, and after 200m was warning about low signal. So, did some one tested real range of this receiver? I'm little scared to fly because previous receiver had 2 antennas and after 200m I had warnings but in this new receiver there is no signal strength warning.
NewNickPL i use this receiver only for my 90mm micro brushless. so i dont fly more then 150m. but i saw a review where this receiver was used more then 200m.
Hey man thank you so much for this video been trying to get my first build going for awhile just trial and error method kinda scary at first but it worked again thank you
Eh up, I think the receiver has 3 modes, PPM, Ibus (default) and Sbus. To change modes from Ibus to Sbus, hold the bind button in when your bound up and tx is on. ( think light goes off for 1 second then flashes twice for Ibus, light comes on for 1 second then flashes twice for Sbus) or visa versa? www.multirotormania.com/receivers/1608-flysky-fs-a8s-fs-a8s-24g-8ch-mini-receiver-ppmi-bussbus.html < there's a link to instructions on the bottom of this page. Hope it helps.
who can I set up the FS-A8S two kiss on beta flight it’s already flash with beta flight but I can get it to work what’s the set up you know can you tell me.
Man I'm new to this stuff and it all sounds like a new language. sbus ,I bus, ppm, pwm ,USB vcp but I'm slowly learning and your very explanatory vids will see me threw
Hi i have a problem i hope you can help me, i have fs-a8s and im using fs-i6s remote, the broblem was the reciver want to bind to the remote but actually it's connected if i see in my software"librepilot" ,but there no indication in my rx battrey bar and it show this (?) logo and i have try to reconnect it and try other things but i can't figure out why. Thankyou😊
I’m swapping from a fs rx2a to a fs ia8b. I have bound to my transmitter but when I go into betaflight I can’t move my throttle etc values. Ppm mode is on I don’t know what else to do
Hi, I have this receiver and I have interference problems. When I go to maximum gas I lose for 1 second aprox the communication with the station. Have you had any problems of this type? I use motors t-motor f40 fc kiss, esc kiss and I use a flysky i10, thank you.
Thank you for this more complete information! Much appreciated, I have found the info i needed to power my RX from a different locale (ie not serial powered)
Hi project Blue Falcon , thanks for the explanation, especially that part where you can ignore the ppm/pwm on the leftside when ibus is selected, because that confusing thing is the same on i6. Would you happend to know if i can disable the internal receiver on a mobula (crazybee F3 Pro) and add an ibus RX.
I have a turnigy evo bound on ibus as well, good video. But i have had some problems out of my remote and noticed on screen at the end of your video your was doing the same thing mine was, drifting on roll.. and the roll wont be still @ 1500. It flutters 1495-1505 on my end. I could trim it out to stop the roll but it still flutters on screen, as soon as i touch the stick again the roll would continue slowly after the stick was returned.. and is very noticeable in flight, since i fly in acro all the time. This is the first time ive seen this in another evo besides mine. Would you mind checking that i wasnt seeing things there? I have sent my remote back for a refund beacause of that issue. I tried everything..
HyperLite F4 Flight Controller i have a issue with a d4r-2 and cant get it to respond on betaflight and quad wont even arm when unhooked from betaflight? what would problem be? i got this from droneproz and i have alot of money over all trying to get at least one drone going 1200$ cause i got ripped off with ebay seller on one then i went droneproz and im having this issue
Is it possible to hook up one of these receivers to a FuriousFPV NUKE? And where to buy the Turnergy Evolution for 67 dollars and free or cheap shipping? HobbyKing charges 37 dollar shipping.
Please someone help me out when I set up my receiver in betaflight and choose my rx port and receiver provider ibus it keep coming back Spektrum 1024 can't get ibus or nothing else always go back to the same receiver provider not the one I want. This is not the first time that this happened I always just go to PPM because I can't never get it to work on none of my f3 boards. never find a video on that please help
Hi, thank you for this, very informative. Any idea whether the A8S can transmit battery voltage to the receiver? I have the A8S wired to a Walkera Rodeo 110 and using a Flysky i10 Tx. Thank you, David
Hey, I have a problem with my FlySky ia6b (connected via ibus). It works all fine, but my spracing f3 doesn't notice when my transmitter is disconnected -> betaflight failsafe doesn't work! Do anybody know how to fix it?
Hey, thx for this video! I hope I can find some help here... sry for my english, i just want to ask you and the other one here in the comments, if its possible to connect an turnigy on/off switch receiver to this FS A8S receiver to control leds on the radio. i dont have any of these material but i am about to order everything to build my quad, thats why i am interested to know if that is possible. i dont see any channel pins on the FS A8S like on the FS i6B but maybe there are solder possibilities and i cant find any pictures on the internet. Tank you very much for your time! Happy Flying
Can you please help me with adding this receiver to my eachine flyingfrog. imgur.com/a/E1HNA There is an SBUS port but I am not really comfortable deconstructing it to solder direct to the board. My plan was to splice the wires to the current receiver but then I am stuck with PPM. Any advice? Is there any way to convert the cable into one that would plug directly into the SBUS port?
JC, Please let us all know if you start to experience problems with the FS-A8S. There is a thread about it here: www.rcgroups.com/forums/showthread.php?2792377-FS-A8S-help Post #39 has the supposed fix - wrapping the receiver in tin foil. However, people are still experiencing problems with this receiver. I definitely want to use this receiver with my Evolution but the problems concern me... and others.
I thought I understood this Stuff I don't. I have 3 wrecked drone that prove I don't. Here I trying to swreck the 4th it's a baby hawk with a flysky fsi6 that came with my wizard and usmile fs82 receiver. It looks bound led wise. This receive has 3 wires B,R and Y the Y says Ibus there a spot to soldier a 4th wire says ppm. The baby hawk has f3 femite prints hella small. But so theres 3 pins on the front from left to right Y.R. then B = I bus gr. 5v. So soldier the PPM wire on the receiver and to the spot on the board that says ppm the cameras on the power and ground next to the PPM. Or will new firmware fix it. Every thing on my computer says the firmware it infected I tryed my browsers won't let get it. That's from flysky site. I promised my girl friend I'd quit this hobby if I wasn't flying by my birthday that seem do able that was on 28th.my birthday tomorrow. I had a wizard that got stole when I crashed it. 2 scumbags seen me and ran grabbed it ran to there car. Still hard to beleive. My car hella far away. Lizard 95 just came with wrong receiver. Hobby shop talk me into getting a spektrum radio and then it was bricked beta flight didn't see it. Then I bought dark max it seemed perfect but first flight. First punch out. Burst in to fames then wreacked. Camera and 4 in 1 esc wreacked I even have fpv goggles that ive never got to use. And my battery mod in spektrum came loose and wreaked it that why I'm using the flysky. I did in brick the lizard shows up in beta flight. And over half my battery are bad 6 or 7 are. New camera came and esc by the 15 th But no controler. The lizard has dsmx integrated receive how do you change that or can you. I'm 1000 invested bet I flown 10 battery in the wizard. I love when they fly. If you could help figure out the baby hawk before I wreck it too. I can send picks or what ever. I can pay a little bit. I really need some help. From a Noob to dumb to fly
IBUS does work on the F4 boards. Watch here - ruclips.net/video/JjaPWTTmryc/видео.html
Project Blue Falcon
Since most of your tutorials are made with the Flip 32 F3 Omnibus boards , I've changed all 4 of my quads to this board..Works beautifully for the price and OSD is nice also ...Thanks for all the hard work being done , its greatly appreciated believe me !!
Me too, I've got four quads, all run Omnibus boards, 2-F3 and 2-F4s. Despite the pinouts being a little frustrating, I love the boards.
Thanks guys. Yea I did the same thing. All but one of my quads are running F3 or F4 Omnibus boards. As small as 122mm builds to as big as a 650mm GPS build. Great all around FC.
"I do everything by the trial error method..." Bro, thanks so much for making this vid. Where can I send you a case of beer?
Thank you so much, IBUS made the trick for me.
RIP brother!
hold the bind button for 2 seconds, then the receiver changes from ibus to sbus! for me it works with sbus on the evolution
Thanks for the info. I'll give it a try.
Dominik this comment should be featured in the video or in the description. I was about to unsolder this receiver but I noticed this comment. Thanks man!
BTW. Did you checked the real range? I have TGI - i10 and me previous receiver that was supposedly be a >300m like this one but this previous receiver had telemetry, and after 200m was warning about low signal. So, did some one tested real range of this receiver? I'm little scared to fly because previous receiver had 2 antennas and after 200m I had warnings but in this new receiver there is no signal strength warning.
NewNickPL i use this receiver only for my 90mm micro brushless. so i dont fly more then 150m. but i saw a review where this receiver was used more then 200m.
Dominik Tomorrow I will see :D
Thanks buddy.
Took me half a day to find this.
Thank you Project Blue Falcon . R.I.P.
Hey man thank you so much for this video been trying to get my first build going for awhile just trial and error method kinda scary at first but it worked again thank you
Eh up, I think the receiver has 3 modes, PPM, Ibus (default) and Sbus. To change modes from Ibus to Sbus, hold the bind button in when your bound up and tx is on. ( think light goes off for 1 second then flashes twice for Ibus, light comes on for 1 second then flashes twice for Sbus) or visa versa?
www.multirotormania.com/receivers/1608-flysky-fs-a8s-fs-a8s-24g-8ch-mini-receiver-ppmi-bussbus.html < there's a link to instructions on the bottom of this page.
Hope it helps.
Many thanks. I had the doubt about the yellow wire, now I understand that it is only for PPM mode.
who can I set up the FS-A8S two kiss on beta flight it’s already flash with beta flight but I can get it to work what’s the set up you know can you tell me.
Friend this receiver Can I use it in a 220mm racing quad
Man I'm new to this stuff and it all sounds like a new language. sbus ,I bus, ppm, pwm ,USB vcp but I'm slowly learning and your very explanatory vids will see me threw
Hi i have a problem i hope you can help me, i have fs-a8s and im using fs-i6s remote, the broblem was the reciver want to bind to the remote but actually it's connected if i see in my software"librepilot" ,but there no indication in my rx battrey bar and it show this (?) logo and i have try to reconnect it and try other things but i can't figure out why. Thankyou😊
i had successfully bind with fs i6 on my ex110 but quad not responding, its my first racer, please guide.
i changed it to s bus and now it worked thanks!!!
I’m swapping from a fs rx2a to a fs ia8b. I have bound to my transmitter but when I go into betaflight I can’t move my throttle etc values. Ppm mode is on I don’t know what else to do
Some of your flight controllers have SD card slots, why? Can you put a list of flight controllers as well in the description? Thanks.
Hi, I have this receiver and I have interference problems. When I go to maximum gas I lose for 1 second aprox the communication with the station. Have you had any problems of this type? I use motors t-motor f40 fc kiss, esc kiss and I use a flysky i10, thank you.
Thank you for this more complete information! Much appreciated, I have found the info i needed to power my RX from a different locale (ie not serial powered)
Hi project Blue Falcon , thanks for the explanation, especially that part where you can ignore the ppm/pwm on the leftside when ibus is selected, because that confusing thing is the same on i6.
Would you happend to know if i can disable the internal receiver on a mobula (crazybee F3 Pro) and add an ibus RX.
I have a turnigy evo bound on ibus as well, good video. But i have had some problems out of my remote and noticed on screen at the end of your video your was doing the same thing mine was, drifting on roll.. and the roll wont be still @ 1500. It flutters 1495-1505 on my end. I could trim it out to stop the roll but it still flutters on screen, as soon as i touch the stick again the roll would continue slowly after the stick was returned.. and is very noticeable in flight, since i fly in acro all the time. This is the first time ive seen this in another evo besides mine. Would you mind checking that i wasnt seeing things there? I have sent my remote back for a refund beacause of that issue. I tried everything..
HyperLite F4 Flight Controller i have a issue with a d4r-2 and cant get it to respond on betaflight and quad wont even arm when unhooked from betaflight? what would problem be? i got this from droneproz and i have alot of money over all trying to get at least one drone going 1200$ cause i got ripped off with ebay seller on one then i went droneproz and im having this issue
Is it possible to hook up one of these receivers to a FuriousFPV NUKE? And where to buy the Turnergy Evolution for 67 dollars and free or cheap shipping? HobbyKing charges 37 dollar shipping.
What does UART stand for? How to hook these receivers to Furious FPV Nuke Flight Controller?
Please someone help me out when I set up my receiver in betaflight and choose my rx port and receiver provider ibus it keep coming back Spektrum 1024 can't get ibus or nothing else always go back to the same receiver provider not the one I want. This is not the first time that this happened I always just go to PPM because I can't never get it to work on none of my f3 boards. never find a video on that please help
Hi , i have wizard x220s with IRange IRX-I6X , do you think FS-A8S receiver is compatible with my drone ? Where have I to solder on the FC ?
Hi, is the SBus FlySky a8s receiver suitable for naze32 rev6 card?
Any info on the connector name of the A8S Receiver? Thank you
hi,
it´s FS-A8S works via iBus with Revo F4 and TGY-i6 ?
I try some configs in betaflight and does´t work.
Thanks and sorry my english
Does this receiver have telemetry? How do I set that up?
Hi, thank you for this, very informative. Any idea whether the A8S can transmit battery voltage to the receiver? I have the A8S wired to a Walkera Rodeo 110 and using a Flysky i10 Tx.
Thank you,
David
Hey, I have a problem with my FlySky ia6b (connected via ibus). It works all fine, but my spracing f3 doesn't notice when my transmitter is disconnected -> betaflight failsafe doesn't work! Do anybody know how to fix it?
i hope to figure this rx out .after a year of pwm must learn this very confusing just love to fly.a little more info than other videos thanx.
Hey, thx for this video! I hope I can find some help here... sry for my english, i just want to ask you and the other one here in the comments, if its possible to connect an turnigy on/off switch receiver to this FS A8S receiver to control leds on the radio. i dont have any of these material but i am about to order everything to build my quad, thats why i am interested to know if that is possible. i
dont see any channel pins on the FS A8S like on the FS i6B but maybe there are solder possibilities and i cant find any pictures on the internet. Tank you very much for your time! Happy Flying
How far away does this receiver have? Thank you
Grazie mille , con il tuo video sono riuscito a far partire Aurora grazie ancora ciao
Thanks for explaining.. you saved my day..:)
As i check. pushing bind button for 2 seconds it will switch between s.bus and i.bus
Thanks for clue :) choosed sbus no reaction, after setting ibus in betaflight, itstarted to work properly :P
Same here
Obrigado pelo vídeo, ajudou muito 🪽👍
Can you please help me with adding this receiver to my eachine flyingfrog. imgur.com/a/E1HNA There is an SBUS port but I am not really comfortable deconstructing it to solder direct to the board. My plan was to splice the wires to the current receiver but then I am stuck with PPM. Any advice? Is there any way to convert the cable into one that would plug directly into the SBUS port?
Great video, subscribed ☺️
Does Ibus work with Flip32 Omnibus?
Tim Spitz I've got it to work with the F3 omnibus but not the f4. I'm still looking into a solution
Tim Spitz m
Is I-bus really working with the f3 omnibus. I ve a flip 32 omnibus f3 pro v2 . I will try when my receiver come. I hope it will work.
I'm choosing ibus but i don't see any values on receiver tab...
@Sergi Hernandez López still nothing?😭
Great vídeo, thanks
Bloody useful!!! thank you.
Nice info JC
What if it won t save to ibus ?
I'm using betaflight f3
JC, Please let us all know if you start to experience problems with the FS-A8S. There is a thread about it here: www.rcgroups.com/forums/showthread.php?2792377-FS-A8S-help
Post #39 has the supposed fix - wrapping the receiver in tin foil. However, people are still experiencing problems with this receiver. I definitely want to use this receiver with my Evolution but the problems concern me... and others.
I'll check it out and make a video if I find any problems.
r.i.p. mate.
Thank You!
RIP 🙏
I thought I understood this Stuff I don't. I have 3 wrecked drone that prove I don't. Here I trying to swreck the 4th it's a baby hawk with a flysky fsi6 that came with my wizard and usmile fs82 receiver. It looks bound led wise. This receive has 3 wires B,R and Y the Y says Ibus there a spot to soldier a 4th wire says ppm. The baby hawk has f3 femite prints hella small. But so theres 3 pins on the front from left to right Y.R. then B = I bus gr. 5v. So soldier the PPM wire on the receiver and to the spot on the board that says ppm the cameras on the power and ground next to the PPM. Or will new firmware fix it. Every thing on my computer says the firmware it infected I tryed my browsers won't let get it. That's from flysky site. I promised my girl friend I'd quit this hobby if I wasn't flying by my birthday that seem do able that was on 28th.my birthday tomorrow. I had a wizard that got stole when I crashed it. 2 scumbags seen me and ran grabbed it ran to there car. Still hard to beleive. My car hella far away. Lizard 95 just came with wrong receiver. Hobby shop talk me into getting a spektrum radio and then it was bricked beta flight didn't see it. Then I bought dark max it seemed perfect but first flight. First punch out. Burst in to fames then wreacked. Camera and 4 in 1 esc wreacked I even have fpv goggles that ive never got to use. And my battery mod in spektrum came loose and wreaked it that why I'm using the flysky. I did in brick the lizard shows up in beta flight. And over half my battery are bad 6 or 7 are. New camera came and esc by the 15 th But no controler. The lizard has dsmx integrated receive how do you change that or can you. I'm 1000 invested bet I flown 10 battery in the wizard. I love when they fly. If you could help figure out the baby hawk before I wreck it too. I can send picks or what ever. I can pay a little bit. I really need some help.
From a Noob to dumb to fly
me first for the first time...:-)
Lol how does it feel?
g8,,:-)