Did I miss anything? 🧐 Also, if you got at least 10¢ worth of value from this, consider supporting me ko-fi.com/rcwithadam More videos and resources on my website rcwithadam.com/
Hello, I think your video is super good. I have a HappyModel EP1 ExpressLRS 2.4GHz receiver and would like to set the VTX table in Bethaflight, but it cannot find it. what should I do?
All these options I tried however my crossfire reciever only comes on when I plug in a battery 🔋, however it is bound to my radio it just doesn’t show the transmitter linked to it all wiring was checked etc
I'm having the same problem please let me know if you found a fix... my radio was working fine and then I bound it to another quad and that one was working fine and then now I got both of them working and neither of them will work on betaflight it says they're connected but it doesn't show it on betaflight when I move the sticks nothing...
Thanks for the video. I, like many others in this comment section are still stuck after trying what you suggested. You offered to help but so far I've not seen a single reply to a comment from you dude?
I replaced an antenna on my frsky xm+ The receiver is solid green which leads me to believe that my transmitter and receiver are bound. Inputs aren't showing up in betaflight when I'm in the receiver tab. Any ideas on what might be going on?
The xm plus uses 2 protocols like rsxr, I had this problem because I flashed 2 ex and int updates to my radio and my reciver but both regarding the subs mode, I was on cppm protocall, u have to set them to the right protocall to make them respond, as well as give correct stick inputs. I hope this helps
Hey, thanks for the great video! Unfortunately, I'm still struggling with this issue. I have a Taranis Qx7, updated firmware to newest OpenTx, and a R-XSR receiver that I've flashed to the newest version that would work. Quad shows bound to the transmitter. I've played with the betaflight settings for hours, but no luck getting any response in the receiver tab. Any further thoughts?
I've had no luck so far. My plan is scrap the Fr-Sky set up completely and go with a new Tx and Rx. Thinking the TBS Mamba, but haven't purchased it yet.
THANK YOU SO MUCH! I couldn't figure out the way serial Rx switch works until u gave this simple explanation! Been trying everything for hours and finally it's working! thank uuuu
I have a quick question. I have a flysky i6x transmitter and a fs-ia6b receiver with a speedy bee f7 fc and I can't get the fc to recognize the receiver in betaflight. I have tried pretty much every combination of channel on the reciever with ibus/ppm in betaflight configurator. I am not sure if my flight controller is broken (everything else seems to work in betaflight tho) or maybe should I get a sbus reciever? Thanks for the help!
I've bound the tango 2 pro (mpm module installed and updated) to the taycan diatone xsr receiver and I have telemetry confirmation on the radio but the receiver tab on betaflight won't show my stick input in I'm fresh out of ideas, any help would be appreciated
@@MatthewRumble I was able to get mine working properly after I changed my channel mapping to AETR in my tango 2 while setting up a new model. I would check that then double check your betaflight channel mapping. Also make sure while setting up your channels in your tango 2 to turn on any aux switches you want to use. Hopefully that helped there definitely isnt many videos out detailing the tbs mpm and tango 2
Howdy, I’m using Dji remote 2, the work with other drones, but won’t pick up on a few units, the air unit is brand new, but no signal in beta flight. Can something fry on the FC preventing the signal reception?
I had this issue after a firmware flash. In the firmware flash section of Betaflight, the Radio Protocol was defaulting to something other than SBUS (my protocol). I reflashed with SBUS protocol selected and that seemed to have solved my issue.
An additional point (where I stumbled) if your quad has a vista unit in it, it needs a battery attached to show your controller in betaflight. My analogs I could just hook up with the usb cable and that was enough
Thanks for this very helpful Video, 4:03 I'm wondering how can I find out what type of Quadcopter receiver I'm using? Do I check that on Cli by typing ==Version.
great video however it did not resolve my issue. ive the flysky fs 16 x and the flysky fs a 8s both was working then just stopped, tried flashing the firmware doing a fresh install, just nothing. there no bars in beta flight for the tx. i have it wired up on uart 2 and set it up as in video but working
recently installed an HGLRC ZEUS F722 and I have a FLYSKY FS-I6 trabsmitter paired with a FS IA6B . This receiver is hooked up too RX1 on the flight controller(UART 1) as shown on the wiring diagram. I have a solid red light on the receiver and the tranmitter shows TX and RX batter power in the top right of the transmitter display so I beleive it is bound correctly. I have Betaflight receiver set as IBUS and I plugged the battery in also but still nothing. any suggestions?
so ive got the dalrc f405 aoi fc and connected everything correctly. ive checked multiple times. my frsky rxsr is bound to my radiomaster tx16s but betaflight does not show my transmitter under the receiver tab. really irritated!! any help please?!
Recently bought a quad with F7. Receiver R-XSR. RC Radiomaster TX16S. Binding them, RC says "Telemetry recover" shows good signal, but in Betafligh: Reciever tab doesn't reflect any joystick moves. Everything triple checked, even got another receiver and FC. Any thoughts?
im having trouble getting any stick input on the transmitter BNF UZ65 with Internal SPI Frsky Receiver Emax E6 Transmitter Radio Controller (FrSky, D8 Protocol) so i run the bind_rx command, set the transmitter to bind and the drone reacts to it. the led starts flashing to indicate it has binded. But when i look in the betaflight transmitter tab, there's no response for any of the remote input. When i plugin a battery on the drone, the drone shows that its responding to the transmitter when i turn it on and off, but doesn't do anything. - SPI RX support for the receiver mode and - FRSKY_D for the bus receiver any help would be greatly appreciated!! thank you
I'm using an fs82 micro reciever for a FS I6X with a Diatone Mamba F405 MK 2. I have signal wire on RX3 and set to Uart3. Reciever goes solid blue when transmitter is on, but flight controller doesn't seem to know the reciever is connected
Thank you Adam I appreciate it this tutorial thank you 👍🏻👍🏻 I have a question do I need to have a video transmitter antenna installed but I doing my quad without video transmitter?? I don’t have this antenna do I need to buy one in order not to fried my system??? Please let me know thank you....
Hey I got the FS-i6 (not the X version) with FS-IA6 receiver and I cant find an output mode in my settings Any clue as what I should do ? Thanks and God bless :)
Hey Adam I have an Iflight baby nazgul 73mm drone and the flight controller does not show up in Betaflight and I'm wondering if the MSP is turned off in the ports tab. If so how can I reactivate that port so I can fly again? Also windows usb doesn't recognize the fc either but my other drones are fine.
I’ve tried all of the uarts for my receiver and there’s even a “sbus” port that I’ve tried too. Still nothing I got all the settings right and even updated the fc and my r9m is up to date as well and is properly paired to the controller bc of the green light I have. Still nothing
Hey. Just bought a Tyro79 and having issues with my R-XSR talking to the FC. Bridged SBUS & RC is correct and I have re soldered to make sure there's no dry joints. I'm bound to the receiver successfully and all my ports in BF are set correctly but still have no stick inputs. Starting to think the FC is faulty? Thanks
@@geoffprogression Let me know how that goes... I managed to get mine to work by swapping F.Port to SBUS out on the RXSR, I'm not too bothered about telemetry from the vtx. However... I have come across another issue. The FC doesn't power up when the vtx is plugged in and powered by a LiPo. This issue just started happening, I did nothing. I can confirm its the vtx because I took one from another quad and it powers up just fine now. Lesson learnt, my next build with be custom with no cheap crappy Chinese parts :)
So recently I had a perfectly working drone and I’ve been using the old butterflight configurator and just recently I tried the new betaflight 4.3 that just came out. So I flashed it over checked all my ports and everything seems fine but I am still not getting any reading on my Betaflight for transmitter receiving inputs. My FC has a designated plug for my spektrum radio which is satellite RX1 my port is UART1 basically on my FC. I did everything else in this video and still no luck after flashing to the new firmware. Thanks hope there’s a solution.
What process do you use for checking if you're wires are broken? I have a crsf nano rx om a speedybee f7v3 board and it waaaas working right, registering my inputs on betaflight but when I got out and went to do Mt test hover it wouldn't, brought it back in and checked betaflight to find that the inputs weren't being registered. My TX and rx are connected / bound as I'm getting the telemetry reading on tx & solid green light in rx but it's not being detected by the FC. Today I'm going to be de-heat shrinking my rx and testing the wires for continuity via my multimeter but it's just been a battle lol
I reset the beta flight settings amd the transmitter I clicked on all the receivers and it done nothing when I click on the modes tab it does nothing neither
i went through the video and everything is bound together but i cant get any inputs on betaflight i have a speedybee f7 v2 and a tbs crossfire nano rx and i cannot figure this one out
Hi we are having such problems to connect our FS i6 with Flysky 2.4g 6ch FS-iA6B receiver connects but on betaflgtt it does not give any signal ,we are using Sbus
I have a Lumenier F4 FC AIO with SBUS pad on it and I am using R81 receiver connected to that SBUS pad. The receiver shows solid red when I have my radio on but there's nothing moving in betaflight receiver when I do anything on the radio. Any idea what to do?
Hi friend i did it all & it. Not working ☹️ i have beta95x v4 board and i have xm+ reciver and my controller its jumper t lite it’s binding correctly but nothing work at all i dont know what to do and for the wires im putting the y-wire to rx1 and b-wire to gr.. and the red to 5v im not sure what is the problem i try all the settings you saying help please 🤦♂️
Hello im having problem on my protek25 hd crsf rx, it bound and no issues before, now my rx sticks input in bf are not working. I checked all the wire pins are good. And i look at the fc look brand new still. What would be the problem on my case? Thanks in advance.
I've got a FS-I6X controller and trying to pair with a A8S receiver. I can bind them however it doesn't show up with RX signal on the controller and cant find any signals from the receiver when I plug into betaflight. I've got them all working on ibus (controller, receiver and on betaflight). The receiver light stays solid red when I turn the controller on to show that its connected but nothing else seems to show that it is (betaflight or controller). Everything works fine with my X6B receiver but when I change to the A8S it doesn't seem to work. Any advice?
Hey bro, I have a flywoo f4 aio flight controller in a fire nano 20, I'm trying to get my fr sky RS receiver to talk to the FC but no response on betaflight. All the protocol in beta flight is correct, wiring is correct. The rx binds perfectly with my remote. Im stumped. I think this board also comes with a built in elrs receiver. Could that be the cause? Help please 🙏
I was able to bind my Taranis x9d plus to my Frsky R-xsr assct receiver but I’ve verified everything is connected correctly, and all the appropriate UART are on in beta flight but still can’t seem to figure out why I’m not getting any movement with the sticks on the receiver tab.
I have a problem with my fly sky controller. This is not for a quadcopter it's for a remote control truck. The problem is is that I've got two separate units on my 10 channel receiver. One battery is running the truck the other battery is running to other speed controllers. And roof lights. There is power drain in the receiver. I think this because my light bar will not stay set at the setting I wanted at. My light bar is plugged directly into the receiver. My controller also has problem with his battery warning due to this problem. How do I fix it?
have elrs tx and rx. i flashed w bind phrase (the rx) and eveything seemed to work. when i disconnect battery i get telemertry lost warning but the inputs are not shopwing in betaflight to setup switches. am i doing something stupid?
Please help! I'm unable to get my TBS Tango 2 controls to work in betaflight. I've binded to the drone sucessfully but betaflight isn't showing any reaction. I have the Nazgul Evoque F6D o3 air unit, with crossfire built in. Please help!
Im using the same Flyksky receiver and transmitter combo and a speedybee f405 v3 fc. I set everything up correctly but when I take a look at my receiver tab it doesn't show anything (no Bars at all for all the channels) any ideas?
I have an RP2 v3.1.2, solder tx to rx5 and rx to tx5.. selected uart5 port, bind to tx12 v3.0.1. Serial provider crsf. Drone and beta flight not registering transmitter outputs, any help would be appreciated!
I am not a newbie, but back at it after two years and just got some Dji goggles and am putting everything together fine, but cannot get Betaflight to see my bound nano rx! Tried switching tx/rx wires surning on/off soft serial, switching UART's, Radio TAER ATER configs -NO luck withja bright green LED on the nano and seeing outputs on the Taranis all functioning! Any suggestions?
got a lal 5 style and its bound but im getting nothing still.. idk whats going on eveything from the videos seems to check out but im unsure were to go from here
Hi Adam, I have this exact problem. I can't get my Flysky FS-TM10 to talk to my Kakute F7 HDV AIO flight controller? All protocols set correct and have tried FS iA6B and Flit 10 receivers via rx2 and rx4 respectively.
Please help !!! I have a Diatone Mamba f7 dji flight controller and I have installed a TBS Crossfire in it. and It is binded, once the reciever showed ok on Betaflight and then NO it does not work there is a connection telemetery between the tx and rx so that s ok but Betaflight just will not recognise my reciever no matter what I do?
Hey man I recent bought a BNF with the 03 air unit but I got it with ELRS so I could try out a different style of radio than the Dji because that’s all I’ve used so far. I’ve bound goggles and there’s some connection between rx and tx because wen I take power off the fc my radio says “telemerry lost” and vice versa wen I plug it back in. But I can get betaflight to respond to any stick or switch inputs. And I can’t remember if there’s a “c” for connection on my radio. But I have all the settings the way you stated here yet still no feedback on BF I’m stumped!
help! I have ELRS receiver (Happy model ep2 2.4ghz) and jumper t lite transmitter. I have set up: LUA script, flashing both receiver and transmitter, soldered to UART2 like the manual says TX to RX and Rx to Tx ( yes I tried other way too) .. I turn on drone, I turn on transmitter, they are paired.. but in betaflight (yes I enabled serial for UART2 and changed to serial in config tab, protocol to CRSF) there is NO TRANSMITTER SIGNAL. joysticks do nothing, and switches do nothing .. I've been trying to get this drone flying for months
Hi, after crashing a Tyro129 I am having trouble with RX connection with the quad. I tried both an R9MX and XM+, they both used to work with this quad and still bind ok with the remote. Quad behaves ok when connected to betaflight, all features work, vtx is ok, gps locks ok. Only thing that won't work is RX-FC connection, I checked wirings severeral times, pins continuity is ok, I also bypassed the plastic connector and soldered the RX straight to the FC (also trying different input pins), none worked. FC led blinks red all the time R9MX seems to connect intermittantly (remote keeps saying "weak signa", "signal lost", "signal ok") Any ideas on how to throubleshoot this? How can I be sure that the eachine GPS F4 FC is fried? thanks for you help 🙂
Typically, the UART number will correspond with the RX and TX pad number. For example, UART2 in betaflight corresponds with RX2 and TX2 pads. It's best to check the manual or diagram to find the suggested or best open uart to use.
My crossfire micro receiver is bound and lit up and working when I hook up to betaflight receiver tab, but when I hook my battery up all of a sudden I get no movement in the receiver tab, and my receiver is still bound and still lit up green but no movement, until i unplug battery and using usb power. I can't find any help online I've been searching for hours for the problem. Any suggestions would be greatly appreciated.prebuilt quad roma f5 dji. What a faulty receiver cause this?
I have an FrSky R-XSR Ultra SBUS/CPPM D16 16CH, and I have it wired up to the 5v, ground, and SBUS pads on my FC. I also have managed to get it to connect to my radio(TX12), but it still does not show up on betaflight when I move the sticks? I have been trying to figure this out for so long at this point, and I really just want to be done with this.
Hello, I have burned hours trying to find out why my Dji remote does not show any stick movement on beta flight. I know its bound and so are the goggles. Everything is on the latest software. I have the HGLRC Petrel 120X HD 3" 4S Toothpick Racing Drone w/ Caddx Nebula Nano. I know that Betaflight connects fine but I go to the receiver tab and nothing moves. Please help. I have the black Dji remote. Thanks
Hello, I have a Radiolink AT9S Pro radio and a R12DSM receiver. They are bound but will not show up in Betaflight. Im also using the plug-ins so I have no idea if a connection is being made. The FC is a MATEKF405 upgraded and soilder points on the back of the FC are not clear on what pads do what. Any ideas.....lol?
hello , My fly sky i6 is bound but won't control my drone, what do yo think i can do ? the connections are good and the configurations on beta flight are also okay, but still its not responding. please help, what should i do ? Thanks
Hello. I am a beginner and need help setting betafpv 75xhd with (F4 2-4S AIO Brushless Flight Controller 12A V2 (BLHeli_S) and frsky XM +. Binding ok with betafpv tx02 or taranis x lite s..but in betaflight arming flag " RX failsafe ". And no reaction when I move the sticks in the transmitter tab in betaflight ... Tried to set failsafe directly via F / S button or via betaflight ... it doesn't change anything ..
Running a Spektrum DX6e and a Spektrum SPM4650 receiver and a Spektrum F400 FC. The receiver indicates it needs to be connected to a transmit pad, which I have done. But when I set that UART (TX4) Betaflight locks up and no longer sees the FC. When rebooting, the FC doesn't even get recognized. What am I doing? Its driving me nuts!
Just build tyro 79. Tried everything in the vid nothing worked I have a Xiangtat Flysky FS-X8B Receiver and It shows up on the transmitter saying its connected. IDK what to do. Anyhelp?
NO Luck for me on any of this at the moment. HELP. I can connect with Mamba F405MK2 to betaflight. I have a FRSKY R-XSR radio that is bound to my Radiomaster TX16S. If I unplug the battery telemetry drops, plug it back in and telemetry is reconnected so I know radio is talking to transceiver. Betaflight ports show USB VCP in Configuration ON and UART1 has Serial Rx on. I am soldered as per this diagram radio to SBU 5V and the GRD cdn.shopify.com/s/files/1/0027/2708/4144/files/2_b407e904-2a0b-4693-8104-94b9e77468e4.jpg?v=1577331450
hey i have the pusher25 iflight. and just had to replace the FC. now with the new CF the drone seems to work, the crossfire also has a connection to the controller but when Im in betaflight it shows no activities of the Radio when I use the sticks and buttons. Also when Im go down with the nose of the drone, the drone in betaflight will go up with the nose. maybe its because a pusher is inverted whats normal but Im not sure if thats right. so basically first i wanna fix the radio connection issue and then lets see how the drone will fly ^^
@@RCwithAdam1 yes they are and the radio works fine the I was told something about turning something in beta flight from 300 to 600 now I don’t no what need adjusting but what I did was take a old 75 whoop and and this 65 and made it work but I was hoping to do it the right way lol .
FrSky Tandem X18S transmitter with Rxsr receiver. It's bound, it works on other models (to verify). wired properly. SBUS_OUT on Rxsr to rx1 on mamba f411 aio 35a. No dice...
I´m trying to bind my mobula 6 to a Literadio 2se. The Led of the drone stops flashing as soon as i turn the transmitter on but the stick movements don´t show up in betaflight. I also tried this with a emax e6.
Hello, thanks a lot for the video ! i have a problem with my succex e F4 motherboard, when I plug in my receiver (r12dsm bindend with at9s pro), I keep trying different uart ports ( R4, R6... etc) none of this would work, my radio isn't recognised in betaflight, the RX and TX are well binded but nothing happens, I spent many hours trying to solve the problem but betaflight doesn't recognise my radio, the sticks doesn't move in the radio part ... Could you please help, it is getting on my nerves and I feel like I tried everything ...
Hi Sir i have jumper tlite connected to cinelog25(frsky R-xsr) It already connected/bound But i cant see a signal indicator on my tx Others whoop was a signal indicator
Hello, I am trying to bind my a Babyhawk 2 O3 ELRS with the Zorro ELRS version. The red light on the receiver is solid and the Zorro even tells me that telemetry is on or when I dosconnect the battery that it's lost. So somehow I think it should be binded. But I can't arm the drone. Also Zorro does not do anything in Betaflight. Bars don't move. It's just like it is not their. I am actually sure that I updated the Zorro correctly (ExpressLRS) and I also think that I flasehd the Babyhawk correctly. I am trying for over one week now and I do not have any idea how to proceed :/ Can anybody help?
Hey man, I can't get the little bugger to connect to my receiver. It gives me all the proper tones when I plug it in (the three and then the other 2) so it seems to have bound, But it won't arm and I can't get any receiver in Beta flight. The VTX has a solid blue and 3 red blinks/ the boot button has steady red blinks. Any ideas??? I am useing frsky and it is telling me telemetry lost when I unplug so it seems to be connected, the sbus on the F/C is bridged.
Hey, my problem is, I binded and it appears to be o, the taranis even detects the telemetry but doesn´t work. with or without battery connected or betaflight. Nothing lie is not binded but it is!
I have a King Kong that was rebuilt onto a new frame. It flies fine but in BetaFlight my tx will not show up anymore. I use to because I had to set up my toggles for arming, etc. The drone shows up when connected with usb and will do an accelerometer congif but nothing in the receiver or modes windows. When I plug in the battery and usb both it will show up to the rx EXCEPT the pitch stick won't register. Pitch works fine when I fly it along with all other controls. I connected to another drone I have see how it did and all was normal and rx would connect as should. Crazy. Any ideas?
@@RCwithAdam1 It has Flysky recvr. No changes. It flys so no worries but crazy as you say. I loaded the previous BF configurator I had upgraded from thinking that might be the issue but nope same thing. Thanks anyway.
I have a GEPRC Cinelog 25 with the CADDXFPV and GEP-F411-35A AIO receiver. I'm using a DJI FPV remote controller model P1RC.I have the Goggles V2, controller and receiver all binded and still can't get Betaflight to recognize the controller. I have green lights on all parts and can connect the quad to Betaflight but once I try to move the bars on the transmitter part of the menu, nothing moves. I have tried all kinds off stuff and can't get the quad in the air... this is incredibly frustrating.
I have been building and flying for 2 years. All of a sudden I'm stumped. I use ELRS since I got my TX16S but before that I used Crossfire. I have 3 old receivers that are bound to my crossfire module. I just built a new quad with a new Skystars stack and used one of the crossfire receivers and the crossfire module on the new radio. Betaflight does not see my radio. Move the sticks, flip switches and nothing shows up in the receiver or mode tab. Receiver goes green when the radio is on. Plug in or unplug the quad and the radio says telemetry lost, telemetry recovered. Skystars shows UART2 as the place for the receiver. I am on UART 2. UART 2 is turned on just like the directions say. Either the FC is bad and UART 2 doesn't work or the radio firmware isn't working with the Crossfire module. But the radio knows when the module and receiver are connected or not connected, so maybe it's the FC. I'll try using a different UART when I get a chance to mess with it again. I'm using EdgeTX on the radio. Maybe you have a magic answer? I've set up the 4 switches in the mixes page on the radio, but nothing, no channels show up in Betaflight. So receiver sees module, module sees receiver. Radio talks to module to give me the sound notifications of telemetry recovered or lost. Has to be this new FC, right? TX to RX and RX to TX. It's soldered on correctly. Possibly a cold joint? SHouldn't be the case, but maybe I'll try resoldering that first.
@@SpaghettiFPV-tg3qh Sorry but no. I gave up on the Crossfire and just put another ELRS receiver on the quad. It must be something with the firmware on the radio and the receivers?
i upgraded my betaflight and now it won’t connect to my transmitter. I was working just fine on the old version but in this one it wont. it is bound with my receiver but will not show up on betaflight. what do i do.
I have ffollowing problems 1. Transmitter doent show output mode 2, i accidentally soldered i bus input to sbus pad in FC will it ruin my fc 3. Channel mappin in Beta flight isnt working Please help me out
I got this same radio. And it works great with the flysky receiver in my Quad. But I try to bind it to my Radiomaster and it binds but when I Goto betaflight it doesn't work.. Any ideas
I delete everything by mistake on a meteor 65 beta fpv tiny whoop , i have another one so i save on beta flight the firmware on the app android and i download it to the delete board but the tx tab no show on beta flight is spi reciver so im stock there i put spi and frisky D but no bind bottom show either.... plis help me ....
I’m using a diatone mamba f405 board and I’m using a different RX (R9MM) and video TX (Race Ranger) for this build and I cannot get the RX or smart audio to show up. I have changed all my UARTS around so many times. My Taranis and the RX both have the FCC firmware and are connected but it doesn’t want to show up in Betaflight......I’m stumped I’ve got this board on other quads and I have no problems and it’s brand new and soldered well real clean and no bridging
i have 2 acrobee65's. transmitter connects to both of them but the transmitter wont show up on betaflight on one of them. they both have the same exact firmware and settings
Tried everything short of unslodering and resoldering the crossfire nano but I still can't get rid of the RXLoss and CLI codes to arm. Everything is green (crossfire nano, crossfire unit on tx16s) but still no stick controls in Betaflight.
On my case the receptor turns green when i have my transmitter ON ( Frsky x9 lite), i have seen several videos where u change stuff on the sentings etc but it still doesnt work :/. My problem is when i go to the reciever tab on betaflight when i try to move anything on the transmitter doesnt change anything on betaflight. Btw my drone is a Nazgul 5 6S.
This shit sux!! I had control of my quad tried to put on a buzzer didn’t sound right had a constant hum so I removed it and now there’s no stick in beta it all says it’s configured right sbus it started after the buzzer bulogna any thoughts? It’s a babyhawk 1 with 1104 motors
mine turned out to be the ports were setup wrong. weird because i was flying an hour ago with them setup differently. crash soldered some shit and nothing worked and all it was , was a port
I cannot get my transmitter to show up in betaflight I have the mamba f722 mini mk2 with the spektrum spm4650 DSMX receiver and my transmitter is the devo 10 with deviation. Please help!! I have been stuck forever!!!
Did I miss anything? 🧐
Also, if you got at least 10¢ worth of value from this, consider supporting me ko-fi.com/rcwithadam
More videos and resources on my website rcwithadam.com/
Hello, I think your video is super good. I have a HappyModel EP1 ExpressLRS 2.4GHz receiver and would like to set the VTX table in Bethaflight, but it cannot find it. what should I do?
All these options I tried however my crossfire reciever only comes on when I plug in a battery 🔋, however it is bound to my radio it just doesn’t show the transmitter linked to it all wiring was checked etc
I repaired my Nazgul 73mm reciever connection because of this video, thanks a ton!
Hi. What can I do if binding is OK, but sticks don't work nor move in betaflight?
Thanks
Please help did you get around this issue?
same
I'm having the same problem please let me know if you found a fix... my radio was working fine and then I bound it to another quad and that one was working fine and then now I got both of them working and neither of them will work on betaflight it says they're connected but it doesn't show it on betaflight when I move the sticks nothing...
Any update?
@@griffey11 updates?
Thanks for the video. I, like many others in this comment section are still stuck after trying what you suggested. You offered to help but so far I've not seen a single reply to a comment from you dude?
I replaced an antenna on my frsky xm+ The receiver is solid green which leads me to believe that my transmitter and receiver are bound. Inputs aren't showing up in betaflight when I'm in the receiver tab. Any ideas on what might be going on?
did you ever figure it out?
The xm plus uses 2 protocols like rsxr, I had this problem because I flashed 2 ex and int updates to my radio and my reciver but both regarding the subs mode, I was on cppm protocall, u have to set them to the right protocall to make them respond, as well as give correct stick inputs. I hope this helps
Hey, thanks for the great video! Unfortunately, I'm still struggling with this issue. I have a Taranis Qx7, updated firmware to newest OpenTx, and a R-XSR receiver that I've flashed to the newest version that would work. Quad shows bound to the transmitter. I've played with the betaflight settings for hours, but no luck getting any response in the receiver tab. Any further thoughts?
i have the same problem have you got it working?
Me too, my quads essentially bricked
I've had no luck so far. My plan is scrap the Fr-Sky set up completely and go with a new Tx and Rx. Thinking the TBS Mamba, but haven't purchased it yet.
Definitely use a different uart
I'm having the same problem😢
hey, right in this page 0:43 if i try to see if values changes they doesn't, they remain the same. how can i resolve? thanks.
THANK YOU SO MUCH! I couldn't figure out the way serial Rx switch works until u gave this simple explanation! Been trying everything for hours and finally it's working! thank uuuu
I have a quick question. I have a flysky i6x transmitter and a fs-ia6b receiver with a speedy bee f7 fc and I can't get the fc to recognize the receiver in betaflight. I have tried pretty much every combination of channel on the reciever with ibus/ppm in betaflight configurator. I am not sure if my flight controller is broken (everything else seems to work in betaflight tho) or maybe should I get a sbus reciever? Thanks for the help!
This is in no relation to the video, but I'm about to buy a Frsky QX7 and I'm confused to what FCC and LBT are. Which one should I buy?
FCC for us and Canada. LBT Europe. These are region codes and power output of tx accordingly
I've bound the tango 2 pro (mpm module installed and updated) to the taycan diatone xsr receiver and I have telemetry confirmation on the radio but the receiver tab on betaflight won't show my stick input in I'm fresh out of ideas, any help would be appreciated
@Lowkey swe im having the same problems, did you ever figure it out?
same bro!
@@leonardsimmons97 same man
@@MatthewRumble I was able to get mine working properly after I changed my channel mapping to AETR in my tango 2 while setting up a new model. I would check that then double check your betaflight channel mapping. Also make sure while setting up your channels in your tango 2 to turn on any aux switches you want to use. Hopefully that helped there definitely isnt many videos out detailing the tbs mpm and tango 2
@@leonardsimmons97 how do I change the channel mappings
Howdy, I’m using Dji remote 2, the work with other drones, but won’t pick up on a few units, the air unit is brand new, but no signal in beta flight. Can something fry on the FC preventing the signal reception?
I had this issue after a firmware flash. In the firmware flash section of Betaflight, the Radio Protocol was defaulting to something other than SBUS (my protocol). I reflashed with SBUS protocol selected and that seemed to have solved my issue.
An additional point (where I stumbled) if your quad has a vista unit in it, it needs a battery attached to show your controller in betaflight.
My analogs I could just hook up with the usb cable and that was enough
Thanks. Try that out 👍
Thanks for this very helpful Video, 4:03 I'm wondering how can I find out what type of Quadcopter receiver I'm using? Do I check that on Cli by typing ==Version.
great video however it did not resolve my issue. ive the flysky fs 16 x and the flysky fs a 8s both was working then just stopped, tried flashing the firmware doing a fresh install, just nothing. there no bars in beta flight for the tx. i have it wired up on uart 2 and set it up as in video but working
recently installed an HGLRC ZEUS F722 and I have a FLYSKY FS-I6 trabsmitter paired with a FS IA6B . This receiver is hooked up too RX1 on the flight controller(UART 1) as shown on the wiring diagram. I have a solid red light on the receiver and the tranmitter shows TX and RX batter power in the top right of the transmitter display so I beleive it is bound correctly. I have Betaflight receiver set as IBUS and I plugged the battery in also but still nothing. any suggestions?
so ive got the dalrc f405 aoi fc and connected everything correctly. ive checked multiple times. my frsky rxsr is bound to my radiomaster tx16s but betaflight does not show my transmitter under the receiver tab. really irritated!! any help please?!
Can you solve ?
Recently bought a quad with F7. Receiver R-XSR. RC Radiomaster TX16S. Binding them, RC says "Telemetry recover" shows good signal, but in Betafligh: Reciever tab doesn't reflect any joystick moves. Everything triple checked, even got another receiver and FC. Any thoughts?
I have the Qx7 and the same r-xsr with F7 and the same for me. Did you fix this
Someone fix the problem ?
im having trouble getting any stick input on the transmitter
BNF UZ65 with Internal SPI Frsky Receiver
Emax E6 Transmitter Radio Controller (FrSky, D8 Protocol)
so i run the bind_rx command,
set the transmitter to bind and the drone reacts to it.
the led starts flashing to indicate it has binded.
But when i look in the betaflight transmitter tab, there's no response for any of the remote input.
When i plugin a battery on the drone, the drone shows that its responding to the transmitter when i turn it on and off, but doesn't do anything.
- SPI RX support for the receiver mode and
- FRSKY_D for the bus receiver
any help would be greatly appreciated!!
thank you
I'm using an fs82 micro reciever for a FS I6X with a Diatone Mamba F405 MK 2. I have signal wire on RX3 and set to Uart3. Reciever goes solid blue when transmitter is on, but flight controller doesn't seem to know the reciever is connected
nope, i tried everything with Fs-i6 and a fs-x6b receiver with INAV (f405 wing miny - speedybee).... any advise?
Thank you Adam I appreciate it this tutorial thank you 👍🏻👍🏻 I have a question do I need to have a video transmitter antenna installed but I doing my quad without video transmitter?? I don’t have this antenna do I need to buy one in order not to fried my system??? Please let me know thank you....
Does LQ work with i6x and x6b ?
Hey I got the FS-i6 (not the X version) with FS-IA6 receiver and I cant find an output mode in my settings Any clue as what I should do ? Thanks and God bless :)
Were you able to fix the issue? I am having the same problem
Hey Adam I have an Iflight baby nazgul 73mm drone and the flight controller does not show up in Betaflight and I'm wondering if the MSP is turned off in the ports tab. If so how can I reactivate that port so I can fly again? Also windows usb doesn't recognize the fc either but my other drones are fine.
Adam hello???
I’ve tried all of the uarts for my receiver and there’s even a “sbus” port that I’ve tried too. Still nothing I got all the settings right and even updated the fc and my r9m is up to date as well and is properly paired to the controller bc of the green light I have. Still nothing
I’m having the same problem
@@kraigvanderwyk1153 this was months ago I’ve figured it out. I can help possibly.
@@jaredallen8054 I would definitely like to know what your solution was. I’m at a loss.
@@kraigvanderwyk1153 I sent you a dm on facebook
Hey. Just bought a Tyro79 and having issues with my R-XSR talking to the FC. Bridged SBUS & RC is correct and I have re soldered to make sure there's no dry joints. I'm bound to the receiver successfully and all my ports in BF are set correctly but still have no stick inputs. Starting to think the FC is faulty? Thanks
i have the same issue, im trying a ne fc tomorrow when it turns up, if now i have an entire new mamba stack coming, also im useing a taranis x9 lite
@@geoffprogression Let me know how that goes... I managed to get mine to work by swapping F.Port to SBUS out on the RXSR, I'm not too bothered about telemetry from the vtx. However... I have come across another issue. The FC doesn't power up when the vtx is plugged in and powered by a LiPo. This issue just started happening, I did nothing. I can confirm its the vtx because I took one from another quad and it powers up just fine now. Lesson learnt, my next build with be custom with no cheap crappy Chinese parts :)
So recently I had a perfectly working drone and I’ve been using the old butterflight configurator and just recently I tried the new betaflight 4.3 that just came out. So I flashed it over checked all my ports and everything seems fine but I am still not getting any reading on my Betaflight for transmitter receiving inputs. My FC has a designated plug for my spektrum radio which is satellite RX1 my port is UART1 basically on my FC. I did everything else in this video and still no luck after flashing to the new firmware. Thanks hope there’s a solution.
What process do you use for checking if you're wires are broken? I have a crsf nano rx om a speedybee f7v3 board and it waaaas working right, registering my inputs on betaflight but when I got out and went to do Mt test hover it wouldn't, brought it back in and checked betaflight to find that the inputs weren't being registered. My TX and rx are connected / bound as I'm getting the telemetry reading on tx & solid green light in rx but it's not being detected by the FC. Today I'm going to be de-heat shrinking my rx and testing the wires for continuity via my multimeter but it's just been a battle lol
I reset the beta flight settings amd the transmitter I clicked on all the receivers and it done nothing when I click on the modes tab it does nothing neither
i went through the video and everything is bound together but i cant get any inputs on betaflight i have a speedybee f7 v2 and a tbs crossfire nano rx and i cannot figure this one out
Hi we are having such problems to connect our FS i6 with Flysky 2.4g 6ch FS-iA6B receiver connects but on betaflgtt it does not give any signal ,we are using Sbus
I have a Lumenier F4 FC AIO with SBUS pad on it and I am using R81 receiver connected to that SBUS pad. The receiver shows solid red when I have my radio on but there's nothing moving in betaflight receiver when I do anything on the radio. Any idea what to do?
I have the iflight f8 controller and can’t get it to bind . It’s suppose to be frsky compatible with my protek 25. Ant thoughts ?
Hi friend i did it all & it. Not working ☹️ i have beta95x v4 board and i have xm+ reciver and my controller its jumper t lite it’s binding correctly but nothing work at all i dont know what to do and for the wires im putting the y-wire to rx1 and b-wire to gr.. and the red to 5v im not sure what is the problem i try all the settings you saying help please 🤦♂️
Hello im having problem on my protek25 hd crsf rx, it bound and no issues before, now my rx sticks input in bf are not working. I checked all the wire pins are good. And i look at the fc look brand new still. What would be the problem on my case? Thanks in advance.
i am having same remote and trying to connect it with kakute h7 but its not showing any output of the remote in INAV configurator.
I've got a FS-I6X controller and trying to pair with a A8S receiver. I can bind them however it doesn't show up with RX signal on the controller and cant find any signals from the receiver when I plug into betaflight. I've got them all working on ibus (controller, receiver and on betaflight). The receiver light stays solid red when I turn the controller on to show that its connected but nothing else seems to show that it is (betaflight or controller). Everything works fine with my X6B receiver but when I change to the A8S it doesn't seem to work. Any advice?
Never mind. Couldnt get it working with ibus but when I changed everything to sbus it worked :)
Hey bro, I have a flywoo f4 aio flight controller in a fire nano 20, I'm trying to get my fr sky RS receiver to talk to the FC but no response on betaflight. All the protocol in beta flight is correct, wiring is correct. The rx binds perfectly with my remote. Im stumped. I think this board also comes with a built in elrs receiver. Could that be the cause? Help please 🙏
I was able to bind my Taranis x9d plus to my Frsky R-xsr assct receiver but I’ve verified everything is connected correctly, and all the appropriate UART are on in beta flight but still can’t seem to figure out why I’m not getting any movement with the sticks on the receiver tab.
I have a problem with my fly sky controller. This is not for a quadcopter it's for a remote control truck. The problem is is that I've got two separate units on my 10 channel receiver. One battery is running the truck the other battery is running to other speed controllers. And roof lights. There is power drain in the receiver. I think this because my light bar will not stay set at the setting I wanted at. My light bar is plugged directly into the receiver. My controller also has problem with his battery warning due to this problem. How do I fix it?
I am new and using speedybee F7 V3 and i m not sure if it should be UART2 because by receiver is at R2 and T2
have elrs tx and rx. i flashed w bind phrase (the rx) and eveything seemed to work. when i disconnect battery i get telemertry lost warning but the inputs are not shopwing in betaflight to setup switches. am i doing something stupid?
Please help! I'm unable to get my TBS Tango 2 controls to work in betaflight. I've binded to the drone sucessfully but betaflight isn't showing any reaction. I have the Nazgul Evoque F6D o3 air unit, with crossfire built in. Please help!
Im using the same Flyksky receiver and transmitter combo and a speedybee f405 v3 fc. I set everything up correctly but when I take a look at my receiver tab it doesn't show anything (no Bars at all for all the channels) any ideas?
Mine doesn't have the 'Output Mode' option. It just says PPM Mode. I've got FS-i6 transmitter and FS-IA6B receiver. Any help?
I have an RP2 v3.1.2, solder tx to rx5 and rx to tx5.. selected uart5 port, bind to tx12 v3.0.1. Serial provider crsf. Drone and beta flight not registering transmitter outputs, any help would be appreciated!
I am not a newbie, but back at it after two years and just got some Dji goggles and am putting
everything together fine, but cannot get Betaflight to see my bound nano rx! Tried switching tx/rx wires surning on/off soft serial, switching UART's, Radio TAER ATER configs -NO luck withja bright green LED on the nano and seeing outputs on the Taranis all functioning! Any suggestions?
I am in exact same boat as you, mine is a radiomaster, tried Uarts, Switching tx/rx...same as u green solid light, but no joy !
Did you fix it?
Same problem ! You fix it ?
got a lal 5 style and its bound but im getting nothing still.. idk whats going on eveything from the videos seems to check out but im unsure were to go from here
Hi Adam, I have this exact problem. I can't get my Flysky FS-TM10 to talk to my Kakute F7 HDV AIO flight controller? All protocols set correct and have tried FS iA6B and Flit 10 receivers via rx2 and rx4 respectively.
Please help !!! I have a Diatone Mamba f7 dji flight controller and I have installed a TBS Crossfire in it. and It is binded, once the reciever showed ok on Betaflight and then NO it does not work there is a connection telemetery between the tx and rx so that s ok but Betaflight just will not recognise my reciever no matter what I do?
Hey man I recent bought a BNF with the 03 air unit but I got it with ELRS so I could try out a different style of radio than the Dji because that’s all I’ve used so far. I’ve bound goggles and there’s some connection between rx and tx because wen I take power off the fc my radio says “telemerry lost” and vice versa wen I plug it back in. But I can get betaflight to respond to any stick or switch inputs. And I can’t remember if there’s a “c” for connection on my radio. But I have all the settings the way you stated here yet still no feedback on BF I’m stumped!
I have the same problem. Did you ever get it fixed?
help! I have ELRS receiver (Happy model ep2 2.4ghz) and jumper t lite transmitter. I have set up: LUA script, flashing both receiver and transmitter, soldered to UART2 like the manual says TX to RX and Rx to Tx ( yes I tried other way too) .. I turn on drone, I turn on transmitter, they are paired.. but in betaflight (yes I enabled serial for UART2 and changed to serial in config tab, protocol to CRSF) there is NO TRANSMITTER SIGNAL. joysticks do nothing, and switches do nothing .. I've been trying to get this drone flying for months
Hi, after crashing a Tyro129 I am having trouble with RX connection with the quad.
I tried both an R9MX and XM+, they both used to work with this quad and still bind ok with the remote.
Quad behaves ok when connected to betaflight, all features work, vtx is ok, gps locks ok.
Only thing that won't work is RX-FC connection, I checked wirings severeral times, pins continuity is ok, I also bypassed the plastic connector and soldered the RX straight to the FC (also trying different input pins), none worked.
FC led blinks red all the time
R9MX seems to connect intermittantly (remote keeps saying "weak signa", "signal lost", "signal ok")
Any ideas on how to throubleshoot this? How can I be sure that the eachine GPS F4 FC is fried?
thanks for you help 🙂
keep the transmitter at least 1 meter from the receiver. I'm facing the same fcrx issue unfortunately.
Based on what people are selecting UART3 and you have selected UART6? please answer if possible
You have to check in which UART you connected the reciever
Typically, the UART number will correspond with the RX and TX pad number. For example, UART2 in betaflight corresponds with RX2 and TX2 pads. It's best to check the manual or diagram to find the suggested or best open uart to use.
My crossfire micro receiver is bound and lit up and working when I hook up to betaflight receiver tab, but when I hook my battery up all of a sudden I get no movement in the receiver tab, and my receiver is still bound and still lit up green but no movement, until i unplug battery and using usb power. I can't find any help online I've been searching for hours for the problem. Any suggestions would be greatly appreciated.prebuilt quad roma f5 dji. What a faulty receiver cause this?
Hello, you solved that problem? The same happens to me
Im bound to serial rx also uart is set up and configured but still no stick recognition
I have an FrSky R-XSR Ultra SBUS/CPPM D16 16CH, and I have it wired up to the 5v, ground, and SBUS pads on my FC. I also have managed to get it to connect to my radio(TX12), but it still does not show up on betaflight when I move the sticks? I have been trying to figure this out for so long at this point, and I really just want to be done with this.
Hello I can connect but my pitch shows it’s working n moving but the preview of the drone doesn’t move... any suggestions?
Hello, I have burned hours trying to find out why my Dji remote does not show any stick movement on beta flight. I know its bound and so are the goggles. Everything is on the latest software. I have the HGLRC Petrel 120X HD 3" 4S Toothpick Racing Drone w/ Caddx Nebula Nano. I know that Betaflight connects fine but I go to the receiver tab and nothing moves. Please help. I have the black Dji remote. Thanks
Hi! That's a bummer! Are you sure all the wires are going to the correct pads on the flight controller?
@@RCwithAdam1 hello. There was no wire on Sbus or ground next to it. I did that and now it’s showing movement on betaflight. Thanks for the help.
Hello, I have a Radiolink AT9S Pro radio and a R12DSM receiver. They are bound but will not show up in Betaflight. Im also using the plug-ins so I have no idea if a connection is being made. The FC is a MATEKF405 upgraded and soilder points on the back of the FC are not clear on what pads do what. Any ideas.....lol?
hello , My fly sky i6 is bound but won't control my drone, what do yo think i can do ?
the connections are good and the configurations on beta flight are also okay, but still its not responding. please help, what should i do ? Thanks
Hello.
I am a beginner and need help setting betafpv 75xhd with (F4 2-4S AIO Brushless Flight Controller 12A V2 (BLHeli_S) and frsky XM +. Binding ok with betafpv tx02 or taranis x lite s..but in betaflight arming flag " RX failsafe ". And no reaction when I move the sticks in the transmitter tab in betaflight ... Tried to set failsafe directly via F / S button or via betaflight ... it doesn't change anything ..
Running a Spektrum DX6e and a Spektrum SPM4650 receiver and a Spektrum F400 FC. The receiver indicates it needs to be connected to a transmit pad, which I have done. But when I set that UART (TX4) Betaflight locks up and no longer sees the FC. When rebooting, the FC doesn't even get recognized. What am I doing? Its driving me nuts!
Thanks mate for the awesome video. I am trying to setup TBS Croasfire micro with my good old Fsi6. I can’t figure out how to make this combo work.
Hi! You're welcome! Do you mean you want to connect the crossfire module to the fsi6? I haven't done it, but I think others have.
Just build tyro 79. Tried everything in the vid nothing worked I have a Xiangtat Flysky FS-X8B Receiver and It shows up on the transmitter saying its connected. IDK what to do. Anyhelp?
NO Luck for me on any of this at the moment. HELP.
I can connect with Mamba F405MK2 to betaflight.
I have a FRSKY R-XSR radio that is bound to my Radiomaster TX16S. If I unplug the battery telemetry drops, plug it back in and telemetry is reconnected so I know radio is talking to transceiver.
Betaflight ports show USB VCP in Configuration ON and UART1 has Serial Rx on.
I am soldered as per this diagram radio to SBU 5V and the GRD cdn.shopify.com/s/files/1/0027/2708/4144/files/2_b407e904-2a0b-4693-8104-94b9e77468e4.jpg?v=1577331450
hey i have the pusher25 iflight. and just had to replace the FC. now with the new CF the drone seems to work, the crossfire also has a connection to the controller but when Im in betaflight it shows no activities of the Radio when I use the sticks and buttons. Also when Im go down with the nose of the drone, the drone in betaflight will go up with the nose. maybe its because a pusher is inverted whats normal but Im not sure if thats right. so basically first i wanna fix the radio connection issue and then lets see how the drone will fly ^^
Hello, you solved that problem? The same happens to me
Help! My transmitter is the fs-16x and the reicever and it are paired but they are not showing up in beta flight!
Did any of the solutions from the video help at all?
@@RCwithAdam1 No I had to use the driver fixer. Apparently it hadn't been installed.
I need help setting up my fli14+ to my flysky fs-i6 plz help
Please help my beta 65 iron quad looses signal after take off like 2 feet after take off I don’t have a lap top just a speedybee and a I phone
Hi, Sam! Hmm... it sounds like radio signal issue. Are the antennas connected well? and are the batteries fully charged on the quad and transmitter?
@@RCwithAdam1 yes they are and the radio works fine the I was told something about turning something in beta flight from 300 to 600 now I don’t no what need adjusting but what I did was take a old 75 whoop and and this 65 and made it work but I was hoping to do it the right way lol .
so..everything checked, FC - iFlifgt Succex F4, reciever - Frsky R-XSR, transmitter - taranis x-lite-s. it`s binding but no reactions on controls
FrSky Tandem X18S transmitter with Rxsr receiver. It's bound, it works on other models (to verify). wired properly. SBUS_OUT on Rxsr to rx1 on mamba f411 aio 35a. No dice...
I´m trying to bind my mobula 6 to a Literadio 2se. The Led of the drone stops flashing as soon as i turn the transmitter on but the stick movements don´t show up in betaflight. I also tried this with a emax e6.
Did everything still not working what else could it be. Radio says telemetry and shows signal but nothing in reciever tab on beta flight
Hello, thanks a lot for the video ! i have a problem with my succex e F4 motherboard, when I plug in my receiver (r12dsm bindend with at9s pro), I keep trying different uart ports ( R4, R6... etc) none of this would work, my radio isn't recognised in betaflight, the RX and TX are well binded but nothing happens, I spent many hours trying to solve the problem but betaflight doesn't recognise my radio, the sticks doesn't move in the radio part ... Could you please help, it is getting on my nerves and I feel like I tried everything ...
I need help my crsf receiver is bound to my radio wont do anything on bf and its on uart 3 just like its supposed too be please help
Hi Sir i have jumper tlite connected to cinelog25(frsky R-xsr)
It already connected/bound
But i cant see a signal indicator on my tx
Others whoop was a signal indicator
Hello,
I am trying to bind my a Babyhawk 2 O3 ELRS with the Zorro ELRS version. The red light on the receiver is solid and the Zorro even tells me that telemetry is on or when I dosconnect the battery that it's lost. So somehow I think it should be binded.
But I can't arm the drone. Also Zorro does not do anything in Betaflight. Bars don't move. It's just like it is not their.
I am actually sure that I updated the Zorro correctly (ExpressLRS) and I also think that I flasehd the Babyhawk correctly.
I am trying for over one week now and I do not have any idea how to proceed :/
Can anybody help?
Hey man, I can't get the little bugger to connect to my receiver. It gives me all the proper tones when I plug it in (the three and then the other 2) so it seems to have bound, But it won't arm and I can't get any receiver in Beta flight. The VTX has a solid blue and 3 red blinks/ the boot button has steady red blinks. Any ideas??? I am useing frsky and it is telling me telemetry lost when I unplug so it seems to be connected, the sbus on the F/C is bridged.
Mate i have exact same issue did you ever figure it out?
do you actually need power? I don't have a battery as yet but, I can get some power from my computer F7 goku R-sxr, Hourus X10s...
Hey, my problem is, I binded and it appears to be o, the taranis even detects the telemetry but doesn´t work. with or without battery connected or betaflight. Nothing lie is not binded but it is!
I have a King Kong that was rebuilt onto a new frame. It flies fine but in BetaFlight my tx will not show up anymore. I use to because I had to set up my toggles for arming, etc. The drone shows up when connected with usb and will do an accelerometer congif but nothing in the receiver or modes windows. When I plug in the battery and usb both it will show up to the rx EXCEPT the pitch stick won't register. Pitch works fine when I fly it along with all other controls. I connected to another drone I have see how it did and all was normal and rx would connect as should. Crazy. Any ideas?
That is crazy. I have no idea at the moment. Are the receivers different?
@@RCwithAdam1 It has Flysky recvr. No changes. It flys so no worries but crazy as you say. I loaded the previous BF configurator I had upgraded from thinking that might be the issue but nope same thing. Thanks anyway.
I have a GEPRC Cinelog 25 with the CADDXFPV and GEP-F411-35A AIO receiver. I'm using a DJI FPV remote controller model P1RC.I have the Goggles V2, controller and receiver all binded and still can't get Betaflight to recognize the controller. I have green lights on all parts and can connect the quad to Betaflight but once I try to move the bars on the transmitter part of the menu, nothing moves. I have tried all kinds off stuff and can't get the quad in the air... this is incredibly frustrating.
Have the same issue did you find a fix
OMG thank you sooooo much I thought my FC was dead and I started freeking out!!!
Yay! 😃
I have been building and flying for 2 years. All of a sudden I'm stumped. I use ELRS since I got my TX16S but before that I used Crossfire. I have 3 old receivers that are bound to my crossfire module. I just built a new quad with a new Skystars stack and used one of the crossfire receivers and the crossfire module on the new radio. Betaflight does not see my radio. Move the sticks, flip switches and nothing shows up in the receiver or mode tab. Receiver goes green when the radio is on. Plug in or unplug the quad and the radio says telemetry lost, telemetry recovered. Skystars shows UART2 as the place for the receiver. I am on UART 2. UART 2 is turned on just like the directions say. Either the FC is bad and UART 2 doesn't work or the radio firmware isn't working with the Crossfire module. But the radio knows when the module and receiver are connected or not connected, so maybe it's the FC. I'll try using a different UART when I get a chance to mess with it again. I'm using EdgeTX on the radio. Maybe you have a magic answer? I've set up the 4 switches in the mixes page on the radio, but nothing, no channels show up in Betaflight. So receiver sees module, module sees receiver. Radio talks to module to give me the sound notifications of telemetry recovered or lost. Has to be this new FC, right? TX to RX and RX to TX. It's soldered on correctly. Possibly a cold joint? SHouldn't be the case, but maybe I'll try resoldering that first.
Hello, you solved that problem? The same happens to me
I have exact same issue
Tx16s radio too
Any answers?
@@Adrian-sm8qc Sorry, no. I just bought another ELRS receiver and put the Crossfire stuff away.
@@SpaghettiFPV-tg3qh Sorry but no. I gave up on the Crossfire and just put another ELRS receiver on the quad. It must be something with the firmware on the radio and the receivers?
@@SpaghettiFPV-tg3qh Maybe I needed to run a Crossfire LUA script on the radio? I don't remember what I did to get Crossfire to work originally.
i upgraded my betaflight and now it won’t connect to my transmitter. I was working just fine on the old version but in this one it wont. it is bound with my receiver but will not show up on betaflight. what do i do.
I have ffollowing problems
1. Transmitter doent show output mode
2, i accidentally soldered i bus input to sbus pad in FC will it ruin my fc
3. Channel mappin in Beta flight isnt working
Please help me out
I got this same radio. And it works great with the flysky receiver in my Quad. But I try to bind it to my Radiomaster and it binds but when I Goto betaflight it doesn't work.. Any ideas
What receiver are you using?
@@RCwithAdam1 i got r-xsr and same situation also with radiomaster. Im soo pissed off, trouble with this for 2 days
I delete everything by mistake on a meteor 65 beta fpv tiny whoop , i have another one so i save on beta flight the firmware on the app android and i download it to the delete board but the tx tab no show on beta flight is spi reciver so im stock there i put spi and frisky D but no bind bottom show either.... plis help me ....
I’m using a diatone mamba f405 board and I’m using a different RX (R9MM) and video TX (Race Ranger) for this build and I cannot get the RX or smart audio to show up. I have changed all my UARTS around so many times. My Taranis and the RX both have the FCC firmware and are connected but it doesn’t want to show up in Betaflight......I’m stumped
I’ve got this board on other quads and I have no problems and it’s brand new and soldered well real clean and no bridging
Hmm, maybe flashing the firmware version would help.
@@RCwithAdam1 Firmware is up to date im using 4.2.6...still no response from the RX in betaflight.
i have 2 acrobee65's. transmitter connects to both of them but the transmitter wont show up on betaflight on one of them. they both have the same exact firmware and settings
Tried everything short of unslodering and resoldering the crossfire nano but I still can't get rid of the RXLoss and CLI codes to arm. Everything is green (crossfire nano, crossfire unit on tx16s) but still no stick controls in Betaflight.
Hello, you solved that problem? The same happens to me
I've got a connection between my qx7 and my inflight cidora but no control going 😧
Did you fix it?
same issue bud
On my case the receptor turns green when i have my transmitter ON ( Frsky x9 lite), i have seen several videos where u change stuff on the sentings etc but it still doesnt work :/. My problem is when i go to the reciever tab on betaflight when i try to move anything on the transmitter doesnt change anything on betaflight. Btw my drone is a Nazgul 5 6S.
hmm. What receiver do you have?
Eh, they didn’t work and I figure I should upgrade from a betaflight f4 anyways. Any ideas on an fc with a built-in pdb?
This shit sux!! I had control of my quad tried to put on a buzzer didn’t sound right had a constant hum so I removed it and now there’s no stick in beta it all says it’s configured right sbus it started after the buzzer bulogna any thoughts? It’s a babyhawk 1 with 1104 motors
mine turned out to be the ports were setup wrong. weird because i was flying an hour ago with them setup differently. crash soldered some shit and nothing worked and all it was , was a port
Someone help. My tinyhawk 2 has a xm+ receiver it bind it with my xlite s but the receiver is flashing green only. ? What should I do ?
Actualiza el receptor XM+
Incompatible
I cannot get my transmitter to show up in betaflight I have the mamba f722 mini mk2 with the spektrum spm4650 DSMX receiver and my transmitter is the devo 10 with deviation. Please help!! I have been stuck forever!!!