How and how long to dry white cement craft items. And after how long it will not break if taken out of the mold. Do you have any video about it? Please tell me the drying process.
I normally dry it for 24 hours (room temperature) before i demould. Try to watch my other video on the demould. 99% it will not break. Remember not to expose to sun.
Hi, I got this mould from taobao. I’m not sure if you can access to it or not. If yes, this is the link: 87啊子里子和他会中在在我她啊 m.tb.cn/h.fTiN00U?sm=9a25fc diy水晶滴胶模具笔筒笔座圆形摆台装饰摆件收纳硅胶模具 But if you can’t, I believe you still can get it from aliexpress. The measurement for this mould is H 9.1 x W8.7 🙂
Hello! Just tried make like 5 terrazzo coaster :) but everytime after I sand, it got a lot of bubble and make my coaster had a lot of dots x.x I already tried less water but its the same. I even sand it with 2k sand. Can you give me advise please?
Hi, bubbles is very headache. Bubbles transform due to the air trapped inside your cement. You need to tap it a lot of time. You can try this way. Before pouring your mixture into the mould, try to tap to release some bubble first. Try pour half first and then do the same to another half. By this method, you can release more air. Hope this work.
Hi, I have made a plaster vs cement comparison previously. However it doesn’t turned up. I’m not sure about wall putty yet. Perhaps will try to make this video in future :)
@@BearBearCammy thanks for the prompt reply.Would also like to know if it's water resistant..does it get washed out when it comes in contact with water
Hi! This is my first time I’m going to make small pots and coaster using white cement. But I already made 4 of them but they’re still cracking due to shrinking. I tried to lessen the water but it still do the same. I didn’t know where and what I did wrong. Btw, I’m from philippines. Do you have any clues or ideas on what should I do? Should I add sand? Or maybe I got the wrong white cement?
Hi, if you are using the correct white cement, it won’t break no matter I put slightly too much water. Can make sure the white cement you are using is for renovation? If yes, there won’t be any issue. Every country white cement I’m worried there will be different. I previously try to mix it with plaster and it break too. I would advise you to try out another brand. Good luck :)
Hi dear, there is no brand written on my cement. The seller will just pack it into the normal take away plastic bag. The cement normally cracked due to few factors. It it either too much of water, mix not enough, cement not hard enough, or tap not enough (which still have a lot of bubbles inside). Perhaps next time u can try to compress the mixture more when u put it into the mould? Please let me know again :)
@@peacefulquran114 there is no need to soak the product in the water. Once the mixture done pour into the mould, you have to let it dry for at least 24 hours.
Hi, there is no exact ratio on this because every cement could be different. You can refer to my Q&A video on this :) (Q&A VIDEO) CEMENT Craft All You Need To Know | Why my cement crack? What cement do i use? Brand? ruclips.net/video/qU3MXX9hCOI/видео.html
@@MhabsOppus hi I made some small project just now using cement and I try to measure for you. The ratio I’m using is about 1(water) : 3(cement). If the cement too dry you can still add some water. Hope this help 😉
@@BearBearCammy ohh my gosh thank you so much. I really appreciate it. im just waiting for my materials that I order online. Im excited to make my very 1st coaster. Thanks again.
Hi, I don’t know what is the brand that I’m using. It was repack from a big cement (probably Portland) and resell it as individual packaging. If you want to know more maybe can refer to my FAQ cement video: ruclips.net/video/qU3MXX9hCOI/видео.html
Thank you for the quick reply. I tried making one and throw into the ground to see how strong they are. And it broke into pieces. Can a sealant save them from breaking?
@@fathimashareef606 oh dear why you throw into ground? Whatever fragile item you throw on floor it will break too. Any ceramic, porcelain, pot, cement, they will break 🥹 I don’t think sealant is to prevent them from breaking but will help them to be more durable and water resistant .
i tried making with white cement but its too brittle and it cracks while drying, its frustrating, what am i doing wrong? also tried it with POP but its chalky and i dont think its good as trinket :(
Hello! Tell me, do you protect products only with these sprays?! Can you write what kind of sprays you have? In our country, only the first one is sold, and the second spray can look for an analog. And you don't process the soap dish with anything else? It will quickly deteriorate because of the water?! Sorry, I'm writing through a translator. And in our country, we process the soap dish in a completely different way.
Hi, I have previously make a video on the sealant I use. You can refer to the video here. ruclips.net/video/KrGiUwKG-vM/видео.html For the water resistant of each sealant you can refer there: ruclips.net/video/29-ztNXrHfs/видео.html
Lovely, thank you for sharing. I definitely like the gloss finish.
Thank you :)
@Aloha Akahai hi thanks for the sharing. Will definitely try it next time :)
I love the soap dish. It came out really nice
Thank you! 😊
I like all the projects!
Thank you!
Fantastic! Absolutely gorgeous
Thank you!
Great video! Anxious to try. :)
Great efforts
@@janardhanaraothota8796 thank you ❤️
So Beautiful, I couldn't make it out, what sealer did you use ?
Hi, I’m using the normal clear lacquer paint with gloss finish.
omg. those are the perfect colors i want to achieve... tutorial for this flakes and how you got those colors. best pigment to use?
Hi, I have previously made a video on the colour pigmentation comparison. You may want to have a look:
ruclips.net/video/eGBzEbpgiy8/видео.html
Beautiful ❤good job
Thank you ❤️
Excellent job 🙏😘😍👍
This video is so good!
Thank you! 😀
hey cammy! could we make the chips with white cement also? also spread really thinly and crack them
Hi sure! I make all those colourful chips with white cement too ☺️
How and how long to dry white cement craft items. And after how long it will not break if taken out of the mold. Do you have any video about it? Please tell me the drying process.
I normally dry it for 24 hours (room temperature) before i demould. Try to watch my other video on the demould. 99% it will not break. Remember not to expose to sun.
Please tell how much time you have to leave it to dry.
Can I ask if you can share the link to the cylinder mold? I like the thickness of the rim. Great video!! Thank you.
Hi, I got this mould from taobao. I’m not sure if you can access to it or not. If yes, this is the link:
87啊子里子和他会中在在我她啊 m.tb.cn/h.fTiN00U?sm=9a25fc diy水晶滴胶模具笔筒笔座圆形摆台装饰摆件收纳硅胶模具
But if you can’t, I believe you still can get it from aliexpress. The measurement for this mould is H 9.1 x W8.7 🙂
Hey cammy? i love ur DIY they are dope< would u plz hook me up on where to find the silicon mold's pls
Hi, I have added some links in my description. Hope this help :)
Hello Do you use white rapid cement or just white cement? Thank you from Italy :-)
Hi, I’m using white cement for this project :)
Hey! Do you add sand for strength? Doesnt it break?
Hi dear, I only add white cement and water for this. The cement is strong enough to hold it. It won’t break if you do it in correct steps ☺️
Hello! Just tried make like 5 terrazzo coaster :) but everytime after I sand, it got a lot of bubble and make my coaster had a lot of dots x.x I already tried less water but its the same. I even sand it with 2k sand. Can you give me advise please?
Hi, bubbles is very headache. Bubbles transform due to the air trapped inside your cement. You need to tap it a lot of time. You can try this way. Before pouring your mixture into the mould, try to tap to release some bubble first. Try pour half first and then do the same to another half. By this method, you can release more air. Hope this work.
@@BearBearCammy Ohhh I never thought about that! Will try it tonight, Thankyou so muchhh!!! 💖
Can we use wall putty instead of white cement?Also are the finished products water resistant?
Hi, I have made a plaster vs cement comparison previously. However it doesn’t turned up. I’m not sure about wall putty yet. Perhaps will try to make this video in future :)
@@BearBearCammy thanks for the prompt reply.Would also like to know if it's water resistant..does it get washed out when it comes in contact with water
@@smitha6781 hi, all of these is not water resistant. Water will slowly absorbed in. You need to apply sealant on it.
@@BearBearCammy ok thanks again
Hi! This is my first time I’m going to make small pots and coaster using white cement. But I already made 4 of them but they’re still cracking due to shrinking. I tried to lessen the water but it still do the same. I didn’t know where and what I did wrong. Btw, I’m from philippines. Do you have any clues or ideas on what should I do? Should I add sand? Or maybe I got the wrong white cement?
Hi, if you are using the correct white cement, it won’t break no matter I put slightly too much water. Can make sure the white cement you are using is for renovation? If yes, there won’t be any issue. Every country white cement I’m worried there will be different. I previously try to mix it with plaster and it break too. I would advise you to try out another brand. Good luck :)
what is the name of the spray that you use
There's a link inside the description on which sealant that i'm using. You can watch that video.
@@BearBearCammy it's not there
Where did you purchase your white cement from??
I got it from my local hardware store in my country Malaysia. It is easily to get it here :)
Okay I know just the place to go. I’ll probly try a Home Depot! Thanks! 😀
May i know the exact brand you are using. I'm using white cement too but it's so powdery and easily cracks like chalk. What did i do wrong? 😭
Hi dear, there is no brand written on my cement. The seller will just pack it into the normal take away plastic bag. The cement normally cracked due to few factors. It it either too much of water, mix not enough, cement not hard enough, or tap not enough (which still have a lot of bubbles inside). Perhaps next time u can try to compress the mixture more when u put it into the mould? Please let me know again :)
same. it cracks while it dries and too brittle i can pinch it and it breaks like powder. :(
Are you using regular white cement?
Yes i am
Is water and white cement is your only mixture?
@@juvyannbongato4264 Yes. Only with water :)
I also use those mixtures but it is so weak :(
@@juvyannbongato4264 So far i don't have any issue on white cement. I even use it for my tiles :)
What sealent do you use?
For this is lacquer
Hello, may I ask what's the sealant brand that u use on that soap dish ya? Thank you. 😊
Hi, i'm using the Mr Diy spray paint. (Lacquer)
With what do you use for glossy finishing?
Hi, I’m using clear gloss lacquer from Mr Diy Malaysia
Thank you for sharing
How do you make the chips?
Hi you can refer to this video: ruclips.net/video/68EOBmOUcZU/видео.html
how many days to open the print ?
After 24 hours at least. Up to 48 hours for winter and rainy season.
Hello, what do i do if water builds up in the mould
You can use a paper towel to gently soak the excess water (if alot). Else you can leave it that way. After your cement dry just sand it off.
@@BearBearCammy alright thank youuu
hi where I can buy white cement?
In Malaysia u can get it from any local hardware store.
@@BearBearCammy thank you 😁
Where can I buy white cement please...name or brand...
I got this from my local hardware store in Malaysia. There is no brand on it. You can go your local store to ask for Portland white cement.
Ye paint kon sa use kia he apne please send the name
Colour pigment for cement: ruclips.net/video/eGBzEbpgiy8/видео.html
How long do we have to keep in water
Hi, do you mean the after the cement mix with water? After the mixture mixed well, you do not need to keep. Mixture is ready to go once it mixed well
@@BearBearCammy no, for soaking the finished product
@@peacefulquran114 there is no need to soak the product in the water. Once the mixture done pour into the mould, you have to let it dry for at least 24 hours.
Where do u get the White cement?
Hi, I got them from my local hardware store :)
Hello, what is the exact ratio of water? Thank you
Hi, there is no exact ratio on this because every cement could be different. You can refer to my Q&A video on this :)
(Q&A VIDEO) CEMENT Craft All You Need To Know | Why my cement crack? What cement do i use? Brand?
ruclips.net/video/qU3MXX9hCOI/видео.html
@@BearBearCammy thank you.. gonna check it out
@@MhabsOppus hi I made some small project just now using cement and I try to measure for you. The ratio I’m using is about 1(water) : 3(cement). If the cement too dry you can still add some water. Hope this help 😉
@@BearBearCammy ohh my gosh thank you so much. I really appreciate it.
im just waiting for my materials that I order online.
Im excited to make my very 1st coaster. Thanks again.
What is the name of the cement you used
Hi, I don’t know what is the brand that I’m using. It was repack from a big cement (probably Portland) and resell it as individual packaging. If you want to know more maybe can refer to my FAQ cement video: ruclips.net/video/qU3MXX9hCOI/видео.html
Are these fragile? How to make them strong?
So far I don’t have issue with white cement. They are strong an durable. Make sure you put a sealant as protection.
Thank you for the quick reply. I tried making one and throw into the ground to see how strong they are. And it broke into pieces. Can a sealant save them from breaking?
@@fathimashareef606 oh dear why you throw into ground? Whatever fragile item you throw on floor it will break too. Any ceramic, porcelain, pot, cement, they will break 🥹 I don’t think sealant is to prevent them from breaking but will help them to be more durable and water resistant .
Is this white cement or jesmonite?
white cements stated
i tried making with white cement but its too brittle and it cracks while drying, its frustrating, what am i doing wrong? also tried it with POP but its chalky and i dont think its good as trinket :(
hi, I think i will advise you to try another brand first. Previously it happen on me and i change another brand and it was okay.
How do u make the thumbnail?
You can change it from RUclips Studio my dear.
@@BearBearCammy oh ok ty
Sis what did you use as a spray for gloss finish...the caption was too small i coudnt read
It is Clear Lacquer from Mr Diy. You can refer to this link: ruclips.net/video/29-ztNXrHfs/видео.html
Hello! Tell me, do you protect products only with these sprays?! Can you write what kind of sprays you have? In our country, only the first one is sold, and the second spray can look for an analog. And you don't process the soap dish with anything else? It will quickly deteriorate because of the water?! Sorry, I'm writing through a translator. And in our country, we process the soap dish in a completely different way.
Hi, I have previously make a video on the sealant I use. You can refer to the video here.
ruclips.net/video/KrGiUwKG-vM/видео.html
For the water resistant of each sealant you can refer there:
ruclips.net/video/29-ztNXrHfs/видео.html
Next time can you please use water so we can see it it makes the process easier.
Hi can I know which part of water are you referring so that I can improve in my future video? 😅
Hi
Your's video is a very important
Because I am started in small business but No buying in sri Lanka. And give mold please price I hope me your help.
Have you check my video description? I have list the mold link inside.
@@BearBearCammy I need buying a silicone mould. Please help me
Can we use ceramic powder as well? And this soap dish can be used with water afterwards, right?
White cement and ceramic is both totally different material. Cement harden when mix with water but ceramic harden when press and sintered.